M-system R7 Series Bedienungsanleitung

EM-7812-C Rev.4 P. 1 / 5

INSTRUCTION MANUAL

RTD INPUT MODULE, 4 points

(High-speed Link System) MODEL R7HL-RS4

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

RTD input module...............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVE

• Use dual-shield cables (Shinko Seisen Industry Model

ZHY262 PBA) for the network. If it is not sufﬁcient, use

a ferrite core (Kitagawa Industries Model GRFC-13) for

the network cable.

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V DC rating: 24V ±10%, approx. 90mA

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

• DO NOT set the switches on the module while the power

is supplied. The switches are used only for maintenance

without the power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7HL-RS4

EM-7812-C Rev.4 P. 2 / 5

COMPONENT IDENTIFICATION

X10 X1

STATION ADD.

CNFG.

12345678

10 11 12 13

2341

15 16 17 18

7896

4567

123

■FRONT VIEW■SIDE VIEW

TERM

ON OFF

RUNPWR

Status Indicator LED

Station Address Setting Rotary SW

Operating Mode Setting DIP SW (SW1)

PC Configurator Jack

Input Terminals

Network, Power Supply

Terminals

Terminating Resistor SW

■STATUS INDICATOR LED

ID COLOR FUNCTION

PWR Green Turns on when the internal 5V is sup-

plied normally.

RUN Green Turns on when the refresh data is re-

ceived normally.

■STATION ADDRESS

The left switch determines the sixteenths place digit, while

the right switch does the ones place digit of the address.

The data allocation is 4.

• Full-duplex communication

Setting “n” with the rotary switches, the addresses are n,

n+2, n+4 and n+6. (Range: 01H to 39H)

• Half-duplex communication

Four (4) addresses are assigned from the one set with the

rotary switch. (Range: 01H to 3CH)

Station Address Setting (x1)

Station Address Setting (x16)

■OPERATING MODE

(*) Factory setting

• Burnout (SW1-2)

SW1-2 BURNOUT

OFF Upscale (*)

ON Downscale

• RTD type (SW1-3, 1-4, 1-5, 1-6)

SW1-3 SW1-4 SW1-5 SW1-6 RTD TYPE

OFF OFF OFF OFF Pt 100 (JIS ’97, IEC) (*)

ON OFF OFF OFF Pt 100 (JIS ’89)

OFF ON OFF OFF JPt 100 (JIS ’89)

ON ON OFF OFF Pt 50 Ω (JIS ’81)

OFF OFF ON OFF Ni 100

ON OFF ON OFF Cu 10 @ 25°C

OFF OFF OFF ON Cu 50

ON ON ON ON PC Conﬁgurator setting

• Transfer rate (SW1-8)

SW1-8 TRANSFER RATE

OFF 12 Mbps (*)

ON 6 Mbps

Note: Be sure to set unused SW1-1 and 1-7 to OFF.

■TERMINATING RESISTOR

To use the terminating resistor, turn the switch ON, and

OFF to invalidate. (Factory setting OFF)

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7HL-RS4

EM-7812-C Rev.4 P. 3 / 5

■NETWORK, POWER SUPPLY TERMINAL ASSIGNMENT

• Full-duplex communication

RXD+

567

123

RXD–

24V

TXD+ TXD–

NO. ID FUNCTION, NOTES

1 TXD+ Network (slave, transmission +)

2 TXD– Network (slave, transmission –)

3 FG FG

4 RXD+ Network (master, transmission +)

5 RXD– Network (master, transmission –)

6 +24V Power input (24V DC)

7 0V Power input (0V)

• Half-duplex communication

567

123

–+

24V 0V

NC NC

NO. ID FUNCTION, NOTES

1 NC No connection

2 NC No connection

3 FG FG

4 TR+ Network

5 TR– Network

6 +24V Power input (24V DC)

7 0V Power input (0V)

■INPUT TERMINAL ASSIGNMENT

INA0

INb0

INA1

INB0

INb1

INB1

INA2

INb2

INB2

INA3

INB3

INb3

NO. ID FUNCTION NO. ID FUNCTION

1 NC

No connection

10 INA0 RTD 0-A

2 INB0 RTD 0-B 11 INb0 RTD 0-b

3 NC

No connection

12 INA1 RTD 1-A

4 INB1 RTD 1-B 13 INb1 RTD 1-b

5 NC

No connection

14 NC

No connection

6 NC

No connection

15 INA2 RTD 2-A

7 INB2 RTD 2-B 16 INb2 RTD 2-b

8 NC

No connection

17 INA3 RTD 3-A

9 INB3 RTD 3-B 18 INb3 RTD 3-b

PC CONFIGURATOR

With conﬁgurator software, settings shown below are available.

Refer to the software manual of R7CON for detailed operation.

■CHANNEL INDIVIDUAL SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

RTD Type Pt 100 (JIS ’97, IEC)

Pt 100 (JIS ’89)

JPt 100 (JIS ’89)

Pt 50 Ω (JIS ’81)

Ni 100

Cu 10 @ 25°C

Cu 50

Pt 100 (JIS ’97, IEC)

Temp Unit C, F, K C

Zero scale -32000 to +32000 0

Full scale -32000 to +32000 10000

Bias -320.00 to +320.00 0.00

Gain -3.2000 to +3.2000 1.0000

Zero temp Depends on sensor type 0.00 (degC)

Full temp Depends on sensor type 0.00 (degC)

■CHANNEL BATCH SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Conversion rate 0: 250 msec.

1: 500 msec.

0: 250 msec.

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7HL-RS4

EM-7812-C Rev.4 P. 4 / 5

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

4567

123

10 11 12 13

2341

15 16 17 18

789

DIN RAIL

35mm wide

54 (2.13)

17 (.66)

115 (4.53)

[5 (.20)]

30 (1.18)

3 (.12)5.5 (.22) 50 (1.97) 18.5 (.73)

7–M3 SCREW

TERMINALS

for Network, POWER

18–M3 SCREW

TERMINALS

for INPUT

6 (.24) 6 (.24)

■CONNECTION DIAGRAM

INAn

INBn

INbn

INA0

INB0

INb0

INA1

INB1

INb1

INA2

INB2

INb2

INA3

INB3

INb3

24V DC

TXD–(NC)

TXD+(NC)

RXD–(TR–)

RXD+ (TR+)

RTD

INPUT 0

INPUT 1

INPUT 2

INPUT 3

■ Input Connection Examples

Note 1: Te rminal numbers in parentheses are for half-duplex

communication model.

Note 2: In order to improve EMC performance, bond the FG

terminal to ground.

Caution: FG terminal is NOT a protective conductor terminal.

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.5 N·m

■SOLDERLESS TERMINAL

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable.

Recommended solderless terminal:

• Communication cables

Applicable wire size: 0.2 to 0.5 mm2(AWG 26 to 22)

Recommended manufacturer: Japan Solderless Terminal

MFG. Co., Ltd.

• Others

Applicable wire size: 0.25 to 1.65 mm2(AWG 22 to 16)

Recommended manufacturer: Japan Solderless Terminal

MFG. Co., Ltd. or Nichifu Co., Ltd.

4 (.16) min

3.2 (.13) dia.

mm (inch)

6 (.24) max

3.3 (.13) max

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7HL-RS4

EM-7812-C Rev.4 P. 5 / 5

COMMUNICATION CABLE CONNECTIONS

Master Module

RXD+

RXD–

TXD+

TXD–

(SHIELD)

Slave Module

RXD+

RXD–

TXD+

TXD–

(SHIELD)

Slave Module

TXD+

Terminating

Resistor

TXD–

RXD+

RXD–

SHIELD

Terminating

Resistor

Master Module

TR+

TR–

(SHIELD)

Slave Module

TR+

TR–

(SHIELD)

Slave Module

TR+

TR–

SHIELD

Note: Be sure to turn ON the switch of the terminating resistor located at both ends of the modules.

Terminating

Resistor

Terminating

Resistor

■

MASTER CONNECTION

• Full-duplex communication

• Half-duplex communication

I/O DATA DESCRIPTIONS

Scaling of analog input is conﬁgurable with the conﬁgurator software (model: R7CON). Refer to the software manual for

details.

■ANALOG INPUT

• Di

ADD.n CH0 Unused

Unused

CH1

CH2

CH3

(ADD.n)

ADD.n+2

(ADD.n+1)

ADD.n+4

(ADD.n+2)

ADD.n+6

(ADD.n+3)

• Do

The data is 16-bit binary.

Negative value is represented in 2’s complements.

Address in parentheses are for half-duplex mode.

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

Andere Handbücher für R7 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere M-system E/A-System Handbücher

M-system

M-system 6BSN Bedienungsanleitung

M-system

M-system R3-DA64A Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

M-system

M-system Devicenet R7F4DD-DA16A-H Bedienungsanleitung

M-system

M-system R3-RS8B Bedienungsanleitung

M-system

M-system M5SN Bedienungsanleitung

M-system

M-system R7M-DC4G-R Bedienungsanleitung

M-system

M-system R3-SV8N Bedienungsanleitung

M-system

M-system R3-SV8A Bedienungsanleitung

M-system

M-system R3-BSW Bedienungsanleitung

M-system

M-system R7L-TS4 Bedienungsanleitung

M-system

M-system R7F4HC-DAC32D-K Bedienungsanleitung

M-system

M-system R3S-DA16 Bedienungsanleitung

M-system

M-system R7L-DC16B-R Bedienungsanleitung

M-system

M-system R7D-YS2 Bedienungsanleitung

M-system

M-system R7E-YV2 Bedienungsanleitung

M-system

M-system R7L-EA8 Bedienungsanleitung

M-system

M-system R3-SV16N Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R7C-YS4 Bedienungsanleitung

M-system

M-system M8BS2-041 Bedienungsanleitung

M-system

M-system R30YN16A Bedienungsanleitung

M-system

M-system MDR-8 Bedienungsanleitung

M-system

M-system R3Y-SS16N Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung