M-system R3-TS8 Bedienungsanleitung

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8363 Rev.6 P. 1 / 4

INSTRUCTION MANUAL

THERMOCOUPLE INPUT MODULE

(8 points, isolated) MODEL R3-TS8

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Thermocouple input module (body + 8 CJC sensors)........(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■HOT SWAPPABLE MODULES

• Replacing the module does not affect other modules on

the same base. Thus, the module can be replaced while

the power is ON. However, replacing multiple modules

at once may greatly change live voltage levels. We highly

recommend to replace them one by one.

■GENERAL PRECAUTIONS

• DO NOT set the switches on the module while the power

is supplied. The switches are used only for maintenance

without the power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

INSTALLATION

Use the Installation Base (model: R3-BSx).

R3-TS8

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8363 Rev.6 P. 2 / 4

COMPONENT IDENTIFICATION

SW2SW1

SW3

■FRONT VIEW

ERR LED

RUN LED

■SIDE VIEW

Input 1-4 (SW1)

Input 5-8 (SW2)

T/C

Conv.

Rate

Temp.

Unit

Burnout

■SIDE DIP SW

(*) Factory setting

• Thermocouple Type: SW1, SW2 (selectable per 4 channels)

INPUT 1 through INPUT 4 (SW1)

T/CINPUT 5 through INPUT 8 (SW2)

1234

OFF OFF OFF OFF K (CA) (*)

ON OFF OFF OFF E (CRC)

OFF ON OFF OFF J (IC)

ON ON OFF OFF T (CC)

OFF OFF ON OFF B (RH)

ON OFF ON OFF R

OFF ON ON OFF S

ON ON ON OFF C (WRe 5-26)

OFF OFF OFF ON N

ON OFF OFF ON U

OFF ON OFF ON L

ON ON OFF ON P (Platinel II)

OFF OFF ON ON (PR)

• Burnout: SW3-1

SW3-1 BURNOUT

OFF Upscale (*)

ON Downscale

• Temperature Unit: SW3-2, 3-3

SW3-2 SW3-3 TEMP. UNIT

OFF OFF °C (*)

ON OFF °F

OFF ON K (Absolute Temp)

• Conversion Rate: SW3-4

SW3-4 CONV. RATE

OFF 250 msec. (*)

ON 1 sec.

Note: Be sure to set unused SW1-5 through 1-8, SW2-5

through 2-8 to OFF.

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/green) LED;

Red with burnout;

Green in normal operating conditions.

R3-TS8

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8363 Rev.6 P. 3 / 4

PC CONFIGURATOR

With conﬁgurator software, settings shown below are available.

Refer to the software manual of R3CON for detailed operation.

■CHANNEL INDIVIDUAL SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Zero Scale -32000 to +32000 0

Full Scale -32000 to +32000 10000

Zero Adjust -320.00 to +320.00 0.00

Full Adjust -32000 to +32000 1.0000

Zero Base Depends on sensor type 0.00

Full Base Depends on sensor type 0.00

Unused 0: Enable

1: Disable

0: Enable

■CHANNEL BATCH SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Limit (V0.10 or higher) No check mark: Limits to the scaling values equivalent

to -15 % to +115 %.

Check-marked: Limits within Zero Scale to Full Scale.

No check mark

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

TERMINAL

COVER

130 (5.12)

27.5 (1.08) 109 (4.29) POSITIONING

GUIDE

28–M3

SCREW

6.2

(.24)

R3-TS8

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8363 Rev.6 P. 4 / 4

■CONNECTION DIAGRAM

*For dual redundant communication.

–

T/C

comp. wire

–

INPUT 1

CJC

SENSOR

–

T/C

comp. wire

–

INPUT 2

CJC

SENSOR

–

T/C

comp. wire

–

INPUT 3

CJC

SENSOR

–

T/C

comp. wire

–

INPUT 4

CJC

SENSOR

–

T/C

comp. wire

–

INPUT 5

CJC

SENSOR

–

T/C

comp. wire

–

INPUT 6

CJC

SENSOR

–

T/C

comp. wire

–

INPUT 7

CJC

SENSOR

–

T/C

comp. wire

–

INPUT 8

CJC

SENSOR

BUS CONNECTOR

INTERNAL POWER

INTERNAL BUS A

INTERNAL BUS B*

• Unused Input Channels

INPUT 1

INPUT 2

INPUT 3

INPUT 4

3 6 9

INPUT 5

INPUT 6

INPUT 7

INPUT 8

CJC

SENSOR

Short

CJC

SENSOR

Short

Close across the unused input terminals as shown below.

Unused channels left open are equal to the burnout, which

turns the red ERR LED on and sets a burnout flag at the

PLC or the host device.

When you choose B (RH) thermocouple, shortcircuiting

across the terminal may not be effective to cancel the

burnout flag. Be sure to use the PC Configurator Software

(model: R3CON).

Unused channels can be specified and set so on the PC

Configurator Software without needing to short at the field

terminals.

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.5 N·m

■SOLDERLESS TERMINAL

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable. Solder-

less terminals with insulation sleeve do not ﬁt.

Applicable wire size: 0.3 – 0.5 mm2

Recommended manufacturer: Japan Solderless Terminal

MFG. Co., Ltd., Nichifu Co., Ltd.

12max

6max

3max 4min

3.2 dia.

(mm)

Andere M-system E/A-System Handbücher

M-system

M-system R3-SS8N Bedienungsanleitung

M-system

M-system R3-SV4A Bedienungsanleitung

M-system

M-system R3-BSW Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

M-system

M-system R7E-EC8B Bedienungsanleitung

M-system

M-system R30SVF4 Bedienungsanleitung

M-system

M-system R7K4DH-1-DAC32D Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R7F4HEIP-DAC16C Bedienungsanleitung

M-system

M-system R7G4HEIP-6-DC16A Bedienungsanleitung

M-system

M-system M8BS1-16U0 Bedienungsanleitung

M-system

M-system R80UST4 Bedienungsanleitung

M-system

M-system R80DCT16A2 Bedienungsanleitung

M-system

M-system R7F4DC-DAC16C-H Bedienungsanleitung

M-system

M-system JC-IO Bedienungsanleitung

M-system

M-system R5 Series Bedienungsanleitung

M-system

M-system M5SN Bedienungsanleitung

M-system

M-system R7F4DC-DA16A-J Bedienungsanleitung

M-system

M-system R5T-RS Bedienungsanleitung

M-system

M-system R7F4HC-DAC32D-K Bedienungsanleitung

M-system

M-system R7D-YV2A Bedienungsanleitung

M-system

M-system R3-SV4 Bedienungsanleitung

M-system

M-system R8 Series Bedienungsanleitung

M-system

M-system R3Y-DA16B Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung