M-system R3S-DA16 Bedienungsanleitung

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8931 Rev.1 P. 1 / 3

INSTRUCTION MANUAL

DISCRETE INPUT MODULE

(Di 16 points; with excitation supply, tension clamp terminal block)

MODEL R3S-DA16

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Discrete input module.........................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■HOT SWAPPABLE MODULES

• Replacing the module does not affect other modules on

the same base. Thus, the module can be replaced while

the power is ON. However, replacing multiple modules

at once may greatly change live voltage levels. We highly

recommend to replace them one by one.

■GENERAL PRECAUTIONS

• DO NOT set the switches on the module while the power

is supplied. The switches are used only for maintenance

without the power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

INSTALLATION

Use the Installation Base (model: R3-BSx).

R3S-DA16

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8931 Rev.1 P. 2 / 3

COMPONENT IDENTIFICATION

RUN LED

ERR LED

Status Indicator LED

■FRONT VIEW ■ SIDE VIEW

SW3

Functions

Exc.

Monitor

Read

Rate

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/green) LED;

Red with excitation abnormality;

Green in normal operating conditions.

Input status indicator: Red LED; turns on with the input

ON.

■SIDE DIP SW

(*) Factory setting

• Excitation Monitor: SW3-1

SW EXCITATION MONITOR

WITH (*) WITHOUT

SW3-1 OFF ON

• Read Rate: SW3-2, 3-3, 3-4

SW READ RATE (≤ msec.)

10 (*)1 5 20 50 70 100 200

SW3-2 OFF ON OFF ON OFF ON OFF ON

SW3-3 OFF OFF ON ON OFF OFF ON ON

SW3-4 OFF OFF OFF OFF ON ON ON ON

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

130 (5.12)

27.5 (1.08) 109 (4.29)

120 (4.72)

POSITIONING

GUIDE

R3S-DA16

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8931 Rev.1 P. 3 / 3

■CONNECTION DIAGRAM

INTERNAL BUS A

INTERNAL BUS B*

INTERNAL POWER

*For dual redundant communication..

Di 1

Di 2

Di 3

Di 4

Di 5

Di 6

Di 7

Di 8

Di 9

Di 10

Di 11

Di 12

Di 13

Di 14

Di 15

Di 16

BUS CONNECTOR

WIRING INSTRUCTIONS

■APPLICABLE WIRE SIZE

• Solid: 0.2 to 1.0 mm2(0.55 to 1.12 dia.)

• Stranded: 0.2 to 1.5 mm2

(Tinning wire ends may cause contact failure and therefore

is not recommended.)

• Ferruled:

Unsheathed: 0.25 to 1.5 mm2

Sheathed: 0.25 to 0.75 mm2

• Expose wire conductors by 10 mm (0.39”).

Stripped length

10mm

■CONNECTION PROCEDURE

Insert the wire end until it comes to a full stop while push-

ing slot with the tip of a screw driver as shown below. Be

sure wire insulation is not inside the terminal.

Screw Driver

Power wire

INPUT PIN ASSIGNMENT

PIN No. FUNCTION PIN No. FUNCTION

21 0V 1 Di 1

22 0V 2 Di 2

23 0V 3 Di 3

24 0V 4 Di 4

25 0V 5 Di 5

26 0V 6 Di 6

27 0V 7 Di 7

28 0V 8 Di 8

29 0V 9 NC

30 0V 10 NC

31 0V 11 Di 9

32 0V 12 Di 10

33 0V 13 Di 11

34 0V 14 Di 12

35 0V 15 Di 13

36 0V 16 Di 14

37 0V 17 Di 15

38 0V 18 Di 16

39 0V 19 NC

40 0V 20 NC

FUNCTIONS

■EXCITATION MONITOR

Enabled/disabled with DIP switch setting.

• Excitation Monitor ON

The input is held at the last status when the loss of exci-

tation is detected.

• Excitation Monitor OFF

All input signals are turned off when the loss of excitation

is detected.

Andere M-system E/A-System Handbücher

M-system

M-system R80UST4 Bedienungsanleitung

M-system

M-system R7HL-YV2 Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R7I4DML3-DA32A Bedienungsanleitung

M-system

M-system R3Y-DA16B Bedienungsanleitung

M-system

M-system R7C-YV2 Bedienungsanleitung

M-system

M-system R7C-SV4 Bedienungsanleitung

M-system

M-system R3-US4 Bedienungsanleitung

M-system

M-system M5SN Bedienungsanleitung

M-system

M-system R3-SV16N Bedienungsanleitung

M-system

M-system JC-ECT Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system Devicenet R7F4DD-DAC16C-C Bedienungsanleitung

M-system

M-system R7ML-EA8 Bedienungsanleitung

M-system

M-system R7E-PA8-R Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R80DCT16A2 Bedienungsanleitung

M-system

M-system R7ML-RS4 Bedienungsanleitung

M-system

M-system M5SN-AA Bedienungsanleitung

M-system

M-system M8BS2-041 Bedienungsanleitung

M-system

M-system R3-PC16A Bedienungsanleitung

M-system

M-system R7F4HEIP-DC16A Bedienungsanleitung

M-system

M-system R6S-DA4 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung