M-system R7 Series Bedienungsanleitung

EM-7812-D Rev.4 P. 1 / 5

INSTRUCTION MANUAL

DC VOLTAGE OUTPUT MODULE, 2 points

(High-speed Link System) MODEL R7HL-YV2

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

DC voltage output module..................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVE

• Use dual-shield cables (Shinko Seisen Industry Model

ZHY262 PBA) for the network. If it is not sufﬁcient, use

a ferrite core (Kitagawa Industries Model GRFC-13) for

the network cable.

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V DC rating: 24V ±10%, approx. 100mA

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and output signal for safety.

• DO NOT set the switches on the module while the power

is supplied. The switches are used only for maintenance

without the power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7HL-YV2

EM-7812-D Rev.4 P. 2 / 5

COMPONENT IDENTIFICATION

X10 X1

STATION ADD.

CNFG.

12345678

78910

3452

4567

123

TERM

ON OFF

RUNPWR

■FRONT VIEW■SIDE VIEW

Terminating Resistor SW

Status Indicator LED

Station Address Setting Rotary SW

Output Terminals

Network, Power Supply

Terminals

PC Configurator Jack

Operating Mode Setting DIP SW (SW1)

■STATUS INDICATOR LED

ID COLOR FUNCTION

PWR Green Turns on when the internal 5V is sup-

plied normally.

RUN Green Turns on when the refresh data is re-

ceived normally.

■STATION ADDRESS

The left switch determines the sixteenths place digit, while

the right switch does the ones place digit of the address.

The data allocation is 2.

• Full-duplex communication

Setting “n” with the rotary switches, the addresses are n

and n+2. (Range: 01H to 3DH)

• Half-duplex communication

Two (2) addresses are assigned from the one set with the

rotary switch. (Range: 01H to 3EH)

Station Address Setting (x1)

Station Address Setting (x16)

■OPERATING MODE

(*) Factory setting

• Output range (SW1-3, 1-4, 1-5, 1-6)

SW1-3 SW1-4 SW1-5 SW1-6 OUTPUT RANGE

OFF OFF OFF OFF -10 – +10V DC (*)

ON OFF OFF OFF -5 – +5V DC

OFF ON OFF OFF -1 – +1V DC

ON ON OFF OFF 0 – 10V DC

OFF OFF ON OFF 0 – 5V DC

ON OFF ON OFF 1 – 5V DC

OFF ON ON OFF 0 – 1V DC

ON ON ON OFF -0.5 – +0.5V DC

ON ON ON ON

PC Conﬁgurator setting

• Output at the loss of communication (SW1-7)

SW1-7 OUTPUT AT THE LOSS OF COMMUNICATION

OFF Hold the output (*)

(maintains the last data received normally)

ON Reset the output (to -15% or approx. -11.5V DC)

• Transfer rate (SW1-8)

SW1-8 TRANSFER RATE

OFF 12 Mbps (*)

ON 6 Mbps

Note: Be sure to set unused SW1-1 and 1-2 to OFF.

■TERMINATING RESISTOR

To use the terminating resistor, turn the switch ON, and

OFF to invalidate. (Factory setting OFF)

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7HL-YV2

EM-7812-D Rev.4 P. 3 / 5

■NETWORK, POWER SUPPLY TERMINAL ASSIGNMENT

• Full-duplex communication

RXD+

567

123

RXD–

24V

TXD+ TXD–

NO. ID FUNCTION, NOTES

1 TXD+ Network (slave, transmission +)

2 TXD– Network (slave, transmission –)

3 FG FG

4 RXD+ Network (master, transmission +)

5 RXD– Network (master, transmission –)

6 +24V Power input (24V DC)

7 0V Power input (0V)

• Half-duplex communication

567

123

–+

24V 0V

NC NC

NO. ID FUNCTION, NOTES

1 NC No connection

2 NC No connection

3 FG FG

4 TR+ Network

5 TR– Network

6 +24V Power input (24V DC)

7 0V Power input (0V)

■OUTPUT TERMINAL ASSIGNMENT

VH0

VL0

COM0

VH1

COM1

VL1

COM1

NO. ID FUNCTION NO. ID FUNCTION

1 NC

No connection

6 NC

No connection

2 COM0 Common 0 7 VH0

Wide span volt. 0

3 COM0 Common 0 8 VL0

Narrow span volt. 0

4 COM1 Common 1 9 VH1

Wide span volt. 1

5 COM1 Common 1 10 VL1

Narrow span volt. 1

■OUTPUT RANGE

• Wide span : -10 to +10V DC, -5 to +5V DC, 0 to 10V DC,

0 to 5V DC, 1 to 5V DC

• Narrow span: -1 to +1V DC, 0 to 1V, -0.5 to +0.5V DC

PC CONFIGURATOR

With conﬁgurator software, settings shown below are available.

Refer to the software manual of R7CON for detailed operation.

■CHANNEL INDIVIDUAL SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Output Range -10 to +10 V DC

-5 to +5 V DC

-1 to +1 V DC

0 to 10 V DC

0 to 5 V DC

1 to 5 V DC

0 to 1 V DC

-0.5 to +0.5 V DC

-10 to +10 V DC

Zero scale -32000 to +32000 0

Full scale -32000 to +32000 10000

Bias -320.00 to +320.00 0.00

Gain -3.2000 to +3.2000 1.0000

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7HL-YV2

EM-7812-D Rev.4 P. 4 / 5

TERMINAL CONNECTIONS

Connect the unit as in the diagram.

■EXTERMNAL DIMENSIONS unit: mm (inch)

23415

789

4567

123

DIN RAIL

35mm wide

[5 (.20)]

30 (1.18)

54 (2.13)

17 (.66)

7–M3 SCREW

TERMINALS

for Network, POWER

10–M3 SCREW

TERMINALS

for OUTPUT

115 (4.53)

3 (.12)5.5 (.22) 50 (1.97) 18.5 (.73)

6 (.24) 6 (.24)

■CONNECTION DIAGRAM

7VH0

8VL0

2COM0

3COM0

OUTPUT 0

9VH1

VL1

4COM1

5COM1

OUTPUT 1

VHn

VLn

–

COMn

WIDE SPAN

VOLTAGE

VHn

VLn +

–

COMn

NARROW SPAN

VOLTAGE

24V DC

TXD– (NC)

TXD+ (NC)

RXD– (TR–)

RXD+ (TR+)

■Output Connection Examples

Note 1: Te rminal numbers in parentheses are for half-duplex

communication model.

Note 2: In order to improve EMC performance, bond the FG

terminal to ground.

Caution: FG terminal is NOT a protective conductor terminal.

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.5 N·m

■SOLDERLESS TERMINAL

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable.

Recommended solderless terminal:

• Communication cables

Applicable wire size: 0.2 to 0.5 mm2(AWG 26 to 22)

Recommended manufacturer: Japan Solderless Terminal

MFG. Co., Ltd.

• Others

Applicable wire size: 0.25 to 1.65 mm2(AWG 22 to 16)

Recommended manufacturer: Japan Solderless Terminal

MFG. Co., Ltd. or Nichifu Co., Ltd.

4 (.16) min

3.2 (.13) dia.

mm (inch)

6 (.24) max

3.3 (.13) max

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7HL-YV2

EM-7812-D Rev.4 P. 5 / 5

COMMUNICATION CABLE CONNECTIONS

Master Module

RXD+

RXD–

TXD+

TXD–

(SHIELD)

Slave Module

RXD+

RXD–

TXD+

TXD–

(SHIELD)

Slave Module

TXD+

Terminating

Resistor

TXD–

RXD+

RXD–

SHIELD

Terminating

Resistor

Master Module

TR+

TR–

(SHIELD)

Slave Module

TR+

TR–

(SHIELD)

Slave Module

TR+

TR–

SHIELD

Note: Be sure to turn ON the switch of the terminating resistor located at both ends of the modules.

Terminating

Resistor

Terminating

Resistor

■

MASTER CONNECTION

• Full-duplex communication

• Half-duplex communication

I/O DATA DESCRIPTIONS

Scaling of analog output is conﬁgurable with the conﬁgurator software (model: R7CON). Refer to the software manual for

details.

■ANALOG OUTPUT

CH0Unused

Unused CH1

• Di • Do

ADD.n

(ADD.n)

CH0

CH1

ADD.n+2

(ADD.n+1)

The data is 16-bit binary.

Negative value is represented in 2’s complements.

Address in parentheses are for half-duplex mode.

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

Andere Handbücher für R7 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere M-system E/A-System Handbücher

M-system

M-system R7D-SV4 Bedienungsanleitung

M-system

M-system 6BSN Bedienungsanleitung

M-system

M-system R3-SV16N Bedienungsanleitung

M-system

M-system R3-SV8A Bedienungsanleitung

M-system

M-system R7D-YV2A Bedienungsanleitung

M-system

M-system R3Y-SS16N Bedienungsanleitung

M-system

M-system EtherCAT R7I4DECT-1-YVF4 Bedienungsanleitung

M-system

M-system R7I4DML3-DC32A Bedienungsanleitung

M-system

M-system R3-DA64A Bedienungsanleitung

M-system

M-system M8BS2-042 Bedienungsanleitung

M-system

M-system R3-RS8B Bedienungsanleitung

M-system

M-system R7C-EC16B Bedienungsanleitung

M-system

M-system R7L-EA8 Bedienungsanleitung

M-system

M-system R7D-YS2A Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R3-TS8 Bedienungsanleitung

M-system

M-system R7M-EA8/UL Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R6S-DA4 Bedienungsanleitung

M-system

M-system R7C-YV2 Bedienungsanleitung

M-system

M-system Remote I/O R8 Series Bedienungsanleitung

M-system

M-system R7L-SV4 Bedienungsanleitung

M-system

M-system R7F4HC-DC32B-K Bedienungsanleitung

M-system

M-system R7F4HEIP-DAC16C Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung