M-system R3Y-SV8N Bedienungsanleitung

R3Y-SV8N

P. 1 / 3 EM-8954 Rev.1

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

the contents of the package you received as outlined below.

If you have any problems or questions as for the product,

please contact M-System’s Sales Office or representatives.

■ PACKAGE INCLUDES:

DC voltage input module ............................................ (1)

■ MODEL NO.

Check that model No. described on the specification label is

exactly what you ordered.

■ INSTRUCTION MANUAL

This manual describes necessary points of caution when you

use this product, including installation, connection and basic

maintenance procedures.

INSTRUCTION MANUAL

MODEL R3Y-SV8N

DCVOLTAGE INPUT MODULE

(8 points, non-isolated)

POINTS OF CAUTION

■ CONFORMITY WITH EC DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

figurations, connected devices and connected wires may

affect the protection level of this unit when it is integrated in

a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure CE conformity.

■ HOT INSERTION/REMOVAL OF MODULES

Removing or replacing modules does not affect other modules

on the same backplane. It is possible to replace them without

removing the power supply. However, replacing multiple

modules at once may greatly change line voltage levels. We

recommend that you replace them one by one.

■ ENVIRONMENT

• Indoor use

• When heavy dust or metal particles are present in the air,

install the unit inside proper housing with sufficient ventila-

tion.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH in

order to ensure adequate life span and operation.

■ WIRING

• Do not install cables (power supply, input and output) close

to noise sources (relay drive cable, high frequency line, etc.).

• Do not bind these cables together with those in which noises

are present. Do not install them in the same duct.

■ UNUSED INPUT CHANNELS

• Unused channels left open with certain range settings are

equal to the input lower than -15%, which sets a data

abnormality at the PLC or the host device.

In order to avoid this, use the PC Configurator Software

(model: R3CON) and specify unused channels. Refer to the

PC Configurator users manual.

■ AND ....

• The unit is designed to function as soon as power is

supplied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data sheet.

INSTALLATION

Use the Installation Base (model: R3-BSx).

R3Y-SV8N

P. 2 / 3 EM-8954 Rev.1

COMPONENT IDENTIFICATION

•Conversion Rate: SW3

SW CONVERSION RATE

100 ms (*)50 ms 20 ms 10 ms

SW3-1 OFF ON OFF ON

SW3-2 OFF OFF ON ON

(*) Factory setting

■SIDE DIP SW

•Input Range: SW1, SW2 (selectable per 4 channels)

INPUT 1 through INPUT 4 (SW1)

INPUT 5 through INPUT 8 (SW2) RANGE

1234

OFF OFF OFF OFF

-10 – +10V

(*)

ON OFF OFF OFF -5 – +5V

ON ON OFF OFF 0 – 10V

OFF OFF ON OFF 0 – 5V

ON OFF ON OFF 1 – 5V

RUN LED

ERR LED

■ FRONT VIEW ■ SIDE VIEW

• Pin Assignment

20 A

Input Connector

Range

Input 1-4 (SW1)

Input 5-8 (SW2)

SW1SW2

Conv.

Rate

SW3

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/green) LED;

Red with the input circuit abnormality (AD

converter response failure);

Green in normal operating conditions.

R3Y-SV8N

P. 3 / 3 EM-8954 Rev.1

M-SYSTEM WARRANTY

M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such

productwasoriginallypurchasedifsuchproducthasbeenusedundernormaloperatingconditionsandproperlymaintained,M-System'ssoleliability,andpurchaser'sexclusiveremedies,

under this warranty are, at M-System's option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this warranty. To

submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original sales invoice.

THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR

SPECIAL DAMAGES OF ANY KIND WHATSOEVER.

M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: [email protected]

TERMINAL CONNECTIONS

Connect the unit as in the diagrams below and the next page.

■ DIMENSIONS mm (inch)

130 (5.12)

27.5 (1.08) 110 (4.33) POSITIONING

GUIDE

INTERNAL POWER

BUS A

BUS B*

*For dual redundant communication.

BUS CONNECTOR

20A / 20B

18A / 18B

INPUT 1

16A / 16B

14A / 14B

INPUT 2

12A / 12B

10A / 10B

INPUT 3

8A / 8B

INPUT 4

INPUT 5

INPUT 6

INPUT 7

INPUT 8

COM

6A / 6B

2A / 2B

3A / 3B

4A / 4B

1A / 1B

■ CONNECTION DIAGRAM ■ INPUT CONNECTOR (40-pin)

PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT

1A COM 1B COM

2A COM 2B COM

3A COM 3B COM

4A COM 4B COM

5A NC 5B NC

6A IN8 6B IN8

7A NC 7B NC

8A IN7 8B IN7

9A NC 9B NC

10A IN6 10B IN6

11A NC 11B NC

12A IN5 12B IN5

13A NC 13B NC

14A IN4 14B IN4

15A NC 15B NC

16A IN3 16B IN3

17A NC 17B NC

18A IN2 18B IN2

19A NC 19B NC

20A IN1 20B NC1

Andere M-system E/A-System Handbücher

M-system

M-system R7L-RS4-R Bedienungsanleitung

M-system

M-system R7ML-RS4 Bedienungsanleitung

M-system

M-system R7K4DH-1-DAC32D Bedienungsanleitung

M-system

M-system R30SVF4 Bedienungsanleitung

M-system

M-system R7E-EC8A Bedienungsanleitung

M-system

M-system R7L-TS4-R Bedienungsanleitung

M-system

M-system R7F4HML3-D-DAC32B Bedienungsanleitung

M-system

M-system R3-RS4 Bedienungsanleitung

M-system

M-system R7HL-YV2 Bedienungsanleitung

M-system

M-system R30XN16A Bedienungsanleitung

M-system

M-system M5XPHS Bedienungsanleitung

M-system

M-system R7M-DAC16C-R Bedienungsanleitung

M-system

M-system R3-SV8 Bedienungsanleitung

M-system

M-system M5SN Bedienungsanleitung

M-system

M-system M8BS2-042 Bedienungsanleitung

M-system

M-system R7C-DS4N Bedienungsanleitung

M-system

M-system 60C Bedienungsanleitung

M-system

M-system R7ML-EA8 Bedienungsanleitung

M-system

M-system R3-TS4 Bedienungsanleitung

M-system

M-system R7C-YV2 Bedienungsanleitung

M-system

M-system R7F4DD-DC16B-C Bedienungsanleitung

M-system

M-system R3-PD16C Bedienungsanleitung

M-system

M-system R3-CT8A Bedienungsanleitung

M-system

M-system Mini-MW Series Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung