M-system M5XPHS Bedienungsanleitung

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-2776 P. 1 / 4

INSTRUCTION MANUAL

PEAK HOLD

(PC programmable) MODEL M5XPHS

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner ...............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

The M5XPHS is programmable using the PC Conﬁgurator

Software. For detailed information on the PC conﬁguration,

refer to the M5CFG users manual. The M5CFG PC Con-

ﬁgurator Software is downloadable at M-System’s web site:

https://www.m-system.co.jp

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside a panel.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V DC rating: 24V ±10%, ≤ 1W

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -20 to +65°C

(-4 to +149°F) with relative humidity within 30 to 90%

RH in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

• Install lightning surge protectors for those wires connect-

ed to remote locations.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

TerminalCover

PowerIndicatorLED

ConﬁguratorJack

Body

Speciﬁcation

OutputSettingDIPSW

InputSettingDIPSW

(side)

M5XPHS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-2776 P. 2 / 4

INSTALLATION

Set the unit so that its DIN rail adapter is at the bottom.

■MOUNTING THE UNIT ON A DIN RAIL

A)Hang the upper hook at the rear side of unit on the DIN

rail.

B)Push in the lower in keeping pressing the unit to the DIN

rail.

DIN rail

■REMOVING THE UNIT

A)Pull down the DIN rail adaptor using a minus screwdriv-

er.

B)Pull out the lower part of the unit.

C)Remove the upper part from the DIN rail.

Slider

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram on the side of the unit.

■EXTERNAL DIMENSIONS unit: mm [inch]

94 [3.70]3 [.12]

25 [.98] 41 [1.61] (3.3 [.13])

• When mounting, no extra space is needed between units.

DIN RAIL

35mm wide

8–M3.5 SCREW

7.3 [.29]

■CONNECTION DIAGRAM

–

JACK

Configurator Jack

DC Current

Input (Z1)

–

OUTPUT

–

POWER

HOLD CONTROL

SWa

SWb

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.8 N·m

M5XPHS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-2776 P. 3 / 4

EXTERNAL VIEWS

■LEFT VIEW ■FRONT VIEW

Output Setting

DIP SW Input Setting

DIP SW

SW1

Power Indicator LED

Configurator Jack

4SW2

■RIGHT VIEW

HOLD MODES

■PEAK HOLD MODE

The transmitter output responds only to an increasing signal, holding the maximum value until a higher signal or a command

to reset is received.

■VALLEY HOLD MODE

The transmitter output responds only to a decreasing signal, holding the minimum value until a lower signal or a command

to reset is received.

■PEAK-TO-PEAK HOLD MODE

The transmitter output responds only when the input signal goes over the previously monitored maximum value or goes

below the previously monitored minimum value.

The output is proportional to the peak-to-peak value, absolute difference between the maximum and the minimum values.

HOLD

10%

20%

30%

40%

50%

60%

70%

80%

90%

100%

10%

20%

30%

40%

50%

60%

70%

80%

90%

100%

INPUT

OUTPUT

RESET

• Peak-to-Peak Hold Mode

M5XPHS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-2776 P. 4 / 4

OUTPUT RANGING

The internal DIP switch setting is required to select I/O types before setting a precise I/O range using PC Conﬁgurator Soft-

ware (model: M5CFG).

For detailed information on the PC conﬁguration, refer to the M5CFG users manual.

Table 1. DIP switch settin: Input type

Input Type SW2

1234

0 – 50 mA DC ON OFF OFF OFF

-1000 – +1000 mV DC OFF ON OFF OFF

-10 – +10 V DC OFF OFF OFF OFF

Table 2. DIP switch setting: Output type

Output Type SW1

123456

0 – 20 mA DC ON OFF OFF OFF ON OFF

-5 – +5 V DC OFF ON ON OFF OFF ON

-10 – +10 V DC OFF ON OFF ON OFF ON

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Check DIP switch setting.

3) Power input voltage: Check voltage across the terminal

7 – 8 with a multimeter.

4) Input: Check that the input signal is within 0 – 100% of

the full-scale. When the output does not track the input

signal, check that the terminals 3 – 4 (shortcircuited or

open) is match to the setting.

5) Output: Check that the load resistance meets the de-

scribed speciﬁcations.

POWER INDICATOR LED

The transmitter is provided with a power indicator LED

which blinks in different patterns indicating various oper-

ating status.

The following ﬁgure indicates typical patterns.

LEDONOFFPATTERNSTRANSMITTERSTATUS

Downloadingthesetting

Rangesetting

Fineadjusting

Supplyingaﬁxedoutput

Normal

AbnormalOperation

(corruptionofconﬁgurationdata)

80ms

MAINTENANCE

Regular calibration procedure is explained below:

■CALIBRATION

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accu-

racy described in the data sheet. When the output is out of

tolerance, recalibrate the unit using the PC Conﬁgurator

Software (model: M5CFG).

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

Andere M-system E/A-System Handbücher

M-system

M-system R3-CT8B Bedienungsanleitung

M-system

M-system R80DCT16A2 Bedienungsanleitung

M-system

M-system R3-US4 Bedienungsanleitung

M-system

M-system R7I4DML3-DC32A Bedienungsanleitung

M-system

M-system R7I4DML3-DAC32C Bedienungsanleitung

M-system

M-system R3-TS8 Bedienungsanleitung

M-system

M-system R7F4HC-DC32B-K Bedienungsanleitung

M-system

M-system R3-CT8A Bedienungsanleitung

M-system

M-system R7D-YV2 Bedienungsanleitung

M-system

M-system R7E-EC8B Bedienungsanleitung

M-system

M-system R7F4DC-DAC16D-H Bedienungsanleitung

M-system

M-system R7L-TS4-R Bedienungsanleitung

M-system

M-system R3-SV8A Bedienungsanleitung

M-system

M-system R7F4HML3-D-DAC32B Bedienungsanleitung

M-system

M-system R5T-RS Bedienungsanleitung

M-system

M-system Devicenet R7F4HD-DA32B Bedienungsanleitung

M-system

M-system R3-CZ4 Bedienungsanleitung

M-system

M-system JC-ECT Bedienungsanleitung

M-system

M-system R7F4DD-DC16B-C Bedienungsanleitung

M-system

M-system R1M-GH2T Series Bedienungsanleitung

M-system

M-system Devicenet R7F4DD-DAC16C-H Bedienungsanleitung

M-system

M-system R7M-MS4-R Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R3-SV4A Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung