M-system R8-CT4E Bedienungsanleitung

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9794 Rev.1 P. 1 / 5

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

AC current input module .................................................. (1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside a panel.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■GENERAL PRECAUTIONS

• Before you remove or mount the unit, turn off the power

supply and input signal for safety.

• Switches on the side of the module can be set for mainte-

nance only while the power supply is off. Do not access

them while the power is supplied.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

INSTALLATION

■HOW TO MOUNT THE MODULE ON DIN RAIL

• I/O Module

Confirm that the locking clamps of the I/O module are set.

Insert the module in parallel to the next one while aligning the grooves of

both modules (A & B in the above figure).

Maintain it perpendicularly to the rail.

More I/O modules can be added in the same manner.

AC CURRENT INPUT MODULE

(4 points, RMS sensing, clamp-on current sensor, non-isolated)

MODEL R8-CT4E

R8-CT4E

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9794 Rev.1 P. 2 / 5

• Protective Cover

The protective power is to be attached over the connected I/O module

at the right end.

Align the hooks on the cover with the grooves of the module and slide it

straight until the hooks are latched.

When removing the cover, pull it out while squeezing the hooks inward.

Groove

Hook

■HOW TO UNMOUNT THE MODULE ON DIN RAIL

Release the locking clamps and pull out straight the module.

Caution !

1) Be careful not to hurt your hand by pointed edges of the internal bus

connector.

2) I/O modules cannot hold tightly on the DIN rail by themselves without

power/network module.

Secure them to the position if necessary by using DIN rail end plates.

• Removing an intermediate module

R8-CT4E

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9794 Rev.1 P. 3 / 5

COMPONENT IDENTIFICATION

FRONT VIEW SIDE VIEW

CT1

RUN

CT2

CT3

CT4

Status Indicator LED

Input Status Indicator LED

Internal Bus Connector

Input Connectors

Module Address Setting

Rotary SW

SW1

x10 x1

SW2

CARD ADD.

Terminator DIP SW

SW3Term

Function Setting

DIP SW

12345678

SW4

■INDICATOR LED

LED OPERATION FUNCTION

Status OFF Stopping

Green ON Valid host communication

Green Blinking

Reading/writing conﬁguration

Red ON Setting error

Red Blinking Parameter error

Input

Status

OFF Input data in the range

Red Blinking Input data out of range

■INPUT CONNECTOR ASSIGNMENT

PIN ID FUNCTION

No.

1 kInput

2 NC No connection

3 NC No connection

4 lInput

■MODULE ADDRESS

The left switch determines the tenth place digit, while the

right switch does the ones place digit of the address.

Address is selected between 0 to 30.

(Factory setting: 0)

Module Address Setting (x10)

Module Address Setting (x1)

■OPERATING MODE

(*) Factory setting

• Clamp-on Current Sensor Setting

Same range for all channels. Use PC Conﬁgurator to set

independent ranges per channel.

CLUMP-ON CURRENT SENSOR SW4

123

CLSE-R5 : 0 − 5A AC (*) OFF OFF OFF

CLSE-05 : 0 − 50A AC ON OFF OFF

CLSE-10 : 0 − 100A AC OFF ON OFF

CLSE-20 : 0 − 200A AC ON ON OFF

CLSE-40 : 0 − 400A AC OFF OFF ON

CLSE-60 : 0 − 600A AC ON OFF ON

• Conguration Mode

CONFIGURATION MODE SW4-8

DIP switch setting (*) OFF

PC Conﬁgurator and communication ON

Note: Be sure to set unused SW4-4 through 4-7 to OFF.

■TERMINATOR DIP SW

TERMINATOR SW SW3

Without (*) OFF

With ON

R8-CT4E

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9794 Rev.1 P. 4 / 5

PC CONFIGURATOR

With conﬁgurator software, settings shown below are available.

Refer to the software manual of R8CFG for detailed operation.

■CHANNEL INDIVIDUAL SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Sensor type CLSE-R5

CLSE-05

CLSE-10

CLSE-20

CLSE-40

CLSE-60

CLSE-R5

Lower range value Depends on sensor type 0.000

Upper range value Depends on sensor type 0.000

Fine zero adjustment -320.00 to +320.00 (%) 0.00 (%)

Fine gain adjustment -3.2000 to +3.2000 1.0000

Scaled range Zero -32000 to +32000 0

Scaled range Span -32000 to +32000 10000

Low-end cutout 0.0 to 5.0 (%) 1.0 (%)

■CHANNEL BATCH SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Loss of internal bus communication detection time 0.0 to 99.9 (sec.) 1.0 (sec.)

Conﬁguration mode DIP switch (OFF)

PC (ON)

DIP switch (OFF)

Note: Turn SW4-8 ON to allow programming by the PC Conﬁgurator via the Power/Network Module.

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

115 (4.53)6 (.24)

7 (.28)

6 (.24) 7 (.28)

DIN RAIL

(35 mm wide)

[3 (.12)] [4 (.16)]

12 (.47) 59 (2.32)

55 (2.17)

R8-CT4E

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9794 Rev.1 P. 5 / 5

■CONNECTION DIAGRAM

INPUT 1

INPUT 4

LOAD

SOURCE

LOAD

SOURCE

*Not used

INTERNAL POWER

INTERNAL BUS

EXC. SUPPLY *

BUS CONNECTOR

INPUT

CONNECTOR 1

INPUT

CONNECTOR 4

WIRING INSTRUCTIONS

■e-CON connector

Unit side connector: XN2D-1474-S002 (Omron)

Recommended cable side connector: XN2A-1470 (Omron)*1

Applicable wire size: 0.08 to 0.5 mm2(AWG28 to 20)

Outer sheath diameter: max. 1.5 dia

*1. The cable side connector is not included in the package.

Refer to the speciﬁcations of the product.

Inhaltsverzeichnis

Andere M-system E/A-System Handbücher

M-system

M-system R3-SS16N Bedienungsanleitung

M-system

M-system R7C-DS4N Bedienungsanleitung

M-system

M-system R3-SV8 Bedienungsanleitung

M-system

M-system R7L-RS4-R Bedienungsanleitung

M-system

M-system R7M-DA16-R Bedienungsanleitung

M-system

M-system R7ML-LC2-R Bedienungsanleitung

M-system

M-system R3-WT1 Bedienungsanleitung

M-system

M-system R7L-DC16B Bedienungsanleitung

M-system

M-system R7HL-YV2 Bedienungsanleitung

M-system

M-system R30US4 Bedienungsanleitung

M-system

M-system R3-TS4 Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system M5XPHS Bedienungsanleitung

M-system

M-system R30YN16A Bedienungsanleitung

M-system

M-system R7ML-DC16B-R Bedienungsanleitung

M-system

M-system R7F4HC-DA32-K Bedienungsanleitung

M-system

M-system R7E-EC8A Bedienungsanleitung

M-system

M-system R7ML-LC2 Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R30PA2 Bedienungsanleitung

M-system

M-system R5 Series Bedienungsanleitung

M-system

M-system R3Y-SV8N Bedienungsanleitung

M-system

M-system R7M-TS4-R Bedienungsanleitung

M-system

M-system R7D-YV2/UL Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung