MELICONI CONTROL TV 100 Bedienungsanleitung

Thank you for choosing Meliconi.

The spare CONTROL TV remote control contains all the main functions

of most TV remote controls of the brands listed on the back of the pack.

Keep your Instructions and Code Booklet for future reference.

USING THE KEYS AND FUNCTIONS

The functions described above are only operative

if your appliance also has them.

GB Use

Used to access additional

commands and to program

the remote control.

TV ON/OFF key.

Number keys.

Confirm key.

Control the volume using

+/-. These

key

s can also be

used to move to the right

and left in the MENU.

To select the next (P+) or

previous (P-) channel or

program. These keys can

also be used to move up

and down in the MENU.

To select an external

terminal. Mute

key

User customisation

key

s for memorising

and accessing additional

commands.

Light indicator.

Additional functions.

Fastext functions

or access to the brightness

and colour controls directly

or using the SHIFT key.

Teletext keys:

to access Teletext

to close Teletext and

return to normal viewing

Teletext page hold function

additional Teletext function.

To access your MENU.

Move within the MENU

using the +/- and P +/-

keys or SHIFT

with +/- P +/- depending

on the model of your original

remote control.

SET-UP

Read these instructions

carefully before programming

your remote control!

BRAND SEARCH PROGRAMMING MODE

1.Make sure that the TV is ON.

2.In the code book enclosed, look for

the brand of your TV and make a note

of the code indicated at the side

(e.g. Philips 001) or the code for the

brand indicated by the arrow.

3.Hold down the SHIFT and ON/OFF

keys together until the light indicator at

the top starts to flash indicating that

the remote control is in programming

mode.

4.Release the keys,

within 15 seconds, enter the brand

code previously identified (e.g. 001).

The light indicator flashes

more quickly to indicate

that the remote control

is ready for the search.

5.Point the remote control at the TV.

Press and release slowly one of

the most frequently-used

keys several times STOPPING

when the appliance responds

correctly to the command.

6.When the TV responds correctly,

press SHIFT to confirm.

Three flashes indicate that the

operation has been completed

correctly.

Additional check

Check that some of the other functions

used on your original remote control are

working correctly. If the commands

function incorrectly or erratically, you

have probably entered a code for a

similar but different remote control.

In this case, repeat the search

procedure from point 3.

Identify and make a note of the TV

code which you have searched for,

following the code noting procedure

(see “NOTING THE PROGRAMMED

CODE” section).

NOTE: THE LIGHT INDICATOR

STOPS FLASHING.

The remote control leaves the

programming mode and the light

indicator stops flashing:

•if no keys are pressed for 15 seconds

•if an invalid brand code is entered

•if the code search list is completed.

In this case, go back to point 3 or

switch to programming mode C.

FITTING THE BATTERIES

Before programming and using the remote control, fit the batteries.

The remote control requires 2 new AAA/LR03 alkaline batteries.

Insert the batteries as shown.

•The batteries must be changed once a year.

•Change the batteries if the light indicator starts to

flash during use, this indicates that the batteries are

low and should be changed.

•When you remove the batteries, fit the new ones

within 5 minutes or you may have to reprogram your

remote control.

•Make a note of the code for your TV on the adhesive

label inside the battery cover. This note will be

handy if you have to reprogram your control.

To program the CONTROL TV remote

control, follow the indications

in section A , Bor C.

1.Make sure that the TV is ON.

2.In the code book enclosed,

look for the brand of your TV

and make a note of the first

code indicated BENEATH

the brand previously identified

(e.g. Philips TV 075).

3.Hold down the SHIFT

and ON/OFF keys together

until the light indicator at the top

starts to flash indicating that the

remote control is in programming

mode.

4.Release the keys and press the

numeric key 8 once. Within

the next 15 seconds, key in the three

figure code you noted previously

(e.g. 075).

Three flashes indicate that the code

has been saved correctly. If not, try

the code entry procedure again from

point 3.

Additional check

Point the remote control at the TV.

Check that the appliance responds

correctly to the commands sent.

If there is no response or the appliance

only responds partially or incorrectly,

it is probable that you have used

the wrong code. In this case, try the

procedure again from point 3.

This time, however, use the

NEXT CODE in the list (e.g. 099).

Note down the TV code used to program

the remote control on the adhesive label

inside the battery cover for rapid

consultation.

NOTE: THE LIGHT INDICATOR

STOPS FLASHING

The remote control leaves the

programming mode and the light indicator

stops flashing:

•if no keys are pressed for 15 seconds

•if an invalid brand code is entered.

DIRECT CODE ENTRY

FOR REMOTE CONTROLS VERSIONS

V5 - V6

DIRECT CODE ENTRY

FOR REMOTE CONTROLS VERSIONS FROM

V1 TO V4

PAY ATTENTION TO THE REMOTE CONTROL VERSION

1.Make sure that the TV is ON.

2.In the code book enclosed,

look for the brand of your TV

and make a note of the first

code indicated BENEATH

the brand previously identified

(e.g. Philips 103).

3.Hold down the SHIFT

and ON/OFF keys together

until the light indicator at the top

starts to flash indicating that the

remote control is in programming

mode.

4.Release the keys.

Within 15 seconds, enter the

code previously identified

(e.g. 103). Three flashes indicate

that the code has been saved

correctly. If not, try the code entry

procedure again from point 3.

Additional check

Point the remote control at the TV.

Check that the appliance responds

correctly to the commands sent.

If there is no response or the appliance

only responds partially or incorrectly,

it is probable that you have used

the wrong code. In this case, try the

procedure again from point 3.

This time, however, use the

NEXT CODE in the list (e.g. 111).

Note down the TV code used to program

the remote control on the adhesive label

inside the battery cover for rapid

consultation.

NOTE: THE LIGHT INDICATOR

STOPS FLASHING

The remote control leaves the

programming mode and the light indicator

stops flashing:

•if no keys are pressed for 15 seconds

•if an invalid brand code is entered.

Additional check

Check that some of the other

functions used on your original remote

control are working correctly.

If the commands function incorrectly

or erratically, you have probably

entered a code for a similar but

different remote control.

In this case, repeat the search

procedure from point 2.

1.Make sure that the TV is ON.

2.Hold down the SHIFT

and ON/OFF keys together

until the light indicator at the

top starts to flash indicating

that the remote control is in

programming mode.

3.Release the keys.

Within 15 seconds,

enter the code 000.

The light indicator flashes more

quickly to indicate that the remote

control is ready for the search.

4.Point the remote control at the TV.

Press and release slowly one of

the most frequently used keys

several times STOPPING when

the appliance responds correctly

to the command.

5.When the TV responds correctly,

press SHIFT to confirm.

Three flashes indicate that

the operation has been

completed correctly.

Identify and make a note of the TV

code which you have searched

for, following the code noting procedure

(see “NOTING THE PROGRAMMED

CODE” section).

NOTE: THE LIGHT INDICATOR

STOPS FLASHING.

The remote control leaves the

programming mode and the light

indicator stops flashing:

•if no keys are pressed for 15 seconds

•if the code search list is completed.

GLOBAL SEARCH REMOTE CONTROL PROGRAMMING

This operation may take up to about 20 minutes.

Count the number of flashes for

each code number.

For example, for the code 306, the key

flashes three, zero and six times to

give:

= 3

= 0

= 6

4.Note this code on the label

inside the battery cover

for rapid consultation.

NOTING THE PROGRAMMED CODE

To find the code for your remote control:

1.Hold down the SHIFT and ON/OFF

keys together until the light indicator at

the top starts to flash.

2.Release the SHIFT and ON/OFF keys

and then press and release the 1-/--

key.

3.After a few seconds, the light

indicator communicates the

code you are looking for by flashing

the three numbers separately.

1-/--

Always write down the 3-digit code for your remote control on the label inside the

battery cover after running the search and saving the code. This may be useful if you

need to reprogram your remote control in the event of accidental cancellation or when

you change used batteries. If you forget to write down the code or use the remote

control programming procedures Aor C... don’t worry!

USING THE ADDITIONAL COMMANDS WHICH DO NOT

APPEAR ON THE KEYPAD

Although not indicated on the keypad, some keys can be used for additional commands.

Use your CONTROL TV remote control to find them by pressing the following keys one by one:

2.The most frequently used additional commands like MENU SCROLL – COLOUR -

BRIGHTNESS and NORMALISATION are located as follows:

normalisation

menu (up) +

menu (down) +

menu (right) +

menu (left) +

menu (up)

menu (down)

menu (right)

menu (left)

brightness (-) red

brightness (+) green

color (-) yellow

color (+) blue

brightness (-) + red

brightness (+) + green

color (-) + yellow

color (+) + blue

1-/--

OK AV

REV RIV TUPO CANCEL –+–+–+

TP OFF TP ON FULL EXP EXP ALTO

TIME ORA MEM F MEM TOT TOP BOT I-II

XXX *MENU MENU ●015 014 014 ●015 AV 027 028 027

MIX 10 11

030 058 059

Original remote control / CONTROL

additional functions symbols or numbers

▼

■❙❙

▼

▼ ▼

3.FOR THE LESSER-USED FUNCTIONS, refer to the code book appendix.

Find the symbol table corresponding to the code you saved to program the remote control.

Locate the additional function you require and note down the symbol or number which

appears below it. EXAMPLE: XXX CODE TABLE

COLOURED

KEYS

NOTE :

You cannot use the additional commands unless these were already available on your

original remote control.

There are 4 ways to enable the additional commands:

A - TV function example:

(a – CANCEL ORA)

A symbol appears beneath the function.

a) The symbol is on your remote control.

(b - brightness +)

The symbol is not on your remote control.

b) Find it as indicated in the drawing. Every symbol is allocated a

colour key.

Press the key to transmit the function to the TV. The command stops when you

release the key.

B - TV function example:

(a – FULL TOT)

A symbol against a grey background appears beneath the

function.

a) The symbol is on your remote control.

(b - sleep)

The symbol is not on your remote control.

b) Find it as indicated in the drawing.

Press SHIFT and the key at the same time. The corresponding function is transmitted to the TV

and stops when you release the key.

C – TV function example:

EXP BOT

A number appears beneath the function (028).

Press and hold down SHIFT.

Type in the number, holding down the last digit (8).

The function is transmitted to the TV and stops when you release

the two keys (SHIFT+ 8).

D – TV function example:

contrast +

Both a symbol and a number are displayed beneath the function.

You can apply the command using either the symbol or the

number.

If the symbol is not on the remote control, use the number

following the example Cabove.

INFO-LINE

WARRANTY: 2 years

Tampering or improper product use will void this

guarantee.

Remote control model CONTROL TV

Purchase date

Agent’s stamp

TROUBLESHOOTING

PROBLEM

The TV does not respond and the light

indicator does not light up when you

press a key.

The TV does not respond but the

light indicator lights up.

The light indicator flashes.

The remote control commands are not all

working correctly.

The brand for your TV is not listed in the Code

Book.

SOLUTION

Try some of the other frequently used keys.

If the problem persists, check that the

batteries are fitted correctly.

If necessary replace them

with 2 new 1.5 V AAA/LR03

alkaline batteries.

Check that the batteries are new

and that the remote control is

pointing at the appliance without any

obstacles in the way. If required,

reset the remote control code,

following the programming

procedure Aor Bor C.

The batteries are low. Change them.

You may have used the wrong

code. Reset the remote control code,

following the programming

procedure Aor Bor C.

Set the remote control code,

following the global search

programming procedure C.

If you have any queries about CONTROL TV:

•read this booklet carefully; this will help you to solve almost all problems

•consult our Internet site www.meliconi.com to answer all your queries more easily and quickly.

You can

customise

your remote

control to use

any 4

additional

TV functions,

using the

function keys

F1- F2 - F3 - F4.

In the symbol table corresponding to your

remote control code, locate the additional

function you require and note down the

number which appears below it.

Note that only number functions can be saved

using F1- F2 - F3 - F4.

PROGRAMMABLE KEYS

The function programming procedure is as

follows:

TV function example: EXP BOT

Press and hold down SHIFT and type in the

number written beneath function (028).

Press one of the function keys (e.g. F1)

and hold it down together with SHIFT.

After a few seconds, the light indicator will

emit a series of 3 flashes to indicate that the

function has been saved correctly.

Release SHIFT and F1.

From now on, whenever you press F1,

the additional command just saved is

transmitted to the appliance and stops when

F1 is released.

NOTE: If the light indicator does not flash, repeat the saving procedure described above.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MELICONI Fernbedienung Handbücher

MELICONI

MELICONI FACILE LIGHT Bedienungsanleitung

MELICONI

MELICONI FULLY 8 Bedienungsanleitung

MELICONI

MELICONI CONTROL 5-500 PLUS Bedienungsanleitung

MELICONI

MELICONI Colibri 2 Bedienungsanleitung

MELICONI

MELICONI TLC01 Bedienungsanleitung

MELICONI

MELICONI GumBody Personal 1 Bedienungsanleitung

MELICONI

MELICONI TLC04 Bedienungsanleitung

MELICONI

MELICONI CONTROL 3-300 PLUS - WINDOWS Bedienungsanleitung

MELICONI

MELICONI CONTROL 4 Plus Bedienungsanleitung

MELICONI

MELICONI Personal 4+ Bedienungsanleitung

MELICONI

MELICONI GUMBODY UNIVERSAL 5 SMART Bedienungsanleitung

MELICONI

MELICONI pratico 6 Bedienungsanleitung

MELICONI

MELICONI Algo 2.1 Bedienungsanleitung

MELICONI

MELICONI easytel 2+ Bedienungsanleitung

MELICONI

MELICONI GUMBODY UNIVERSAL 3-300 Bedienungsanleitung

MELICONI

MELICONI Personal 3 plus Installations- und Betriebshandbuch

MELICONI

MELICONI CONTROL 2 Simple Bedienungsanleitung

MELICONI

MELICONI TLC05 Bedienungsanleitung

MELICONI

MELICONI Fully 8.1 Bedienungsanleitung

MELICONI

MELICONI SPEEDY 2 Bedienungsanleitung

MELICONI

MELICONI GumBody DIGITAL 2 SMART Bedienungsanleitung

MELICONI

MELICONI PRATICO 2 Light Bedienungsanleitung

MELICONI

MELICONI EASY 200 Bedienungsanleitung

MELICONI

MELICONI TLC03 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung