MELICONI GumBody DIGITAL 2 SMART Bedienungsanleitung
GB
16
USING THE KEYS AND FUNCTIONS
The functions described below are only available
if they are already foreseen by your TV.
Keep this booklet in case you ever need to consult us in the future.
Thanks to the enclosed CD and to the on-line guide on the site www.meliconi.com/guide it is
even easier and faster to programme the remote control and discover all the potential offered
by the DIGITAL 2 SMART.
SET-UP
Read these instructions carefully before programming your remote control!
Thanks to its large database and numerous functions the DIGITAL 2 SMART remote control is ideal for
replacing up to 2 remote controls of any brands for TV - STB (digital terrestrial or satellite decoder).
Its ergonomic form and casing in soft rubber make it easy to grip and protect it against falls and bumps.
Thank you for choosing a MELICONI remote control.
DIGITAL 2 SMART
Keys for selecting which appliance
you want to use
ON/OFF key for the appliance
Number keys To select an external input terminal
To select the next (P+) or previous
(P-) channel or program
Control the volume using +/ -
Specific area for digital terrestrial
or satellite decoder
To access the MENU
Teletext keys
Confirm key
To move around within the MENU
or to control the
BRIGHTNESS/COLOUR
Fastext functions or to select
submenus by means of the
colours
Impact-proof rubber casing
Light indicator
17
PROGRAMMING USING THE BRAND CODE
FITTING THE BATTERIES
Before programming and using the remote control,
fit the batteries.
To display and make a note of the code memorized by means of the search,
follow the instructions described in the paragraph CURRENT CODE DISPLAY.
ADDITIONAL CHECK
Check that some of the other functions used on your original remote control are working correctly. If the
commands function incorrectly or erratically, you have probably entered a code for a similar remote control
but not the right one. In this case, repeat the search procedure starting from point 3, entering the code
previously used (e.g. 0025).
The TV - STB keys can be programmed according to your requirements, following the procedure described
below.
The quickest and easiest way to programme the remote control is
by consulting the website www.meliconi.com/guide.
Warning: programme one appliance at a time!
• Change the batteries if the light indicator starts to flash
during use. The batteries are low.
• Make a note of the codes for your appliances on the
adhesive label inside the battery cover in case you have
to reprogramme your remote control.
• This remote control has a permanent memory and does
not lose the programmed codes or functions when the
batteries are removed.
The remote control requires 2 new AAA/LR03 batteries. Insert the batteries as shown:
1. Switch ON the appliance you wish to program and select
a program.
2. Search for the brand of your appliance in the list of brands
at the end of this booklet. Record the code indicated
alongside (
e.g. PHILIPS 0025
). Warning: if the brand is
not shown in the list then programming can be per-
formed using the code 0099.
3. Hold down the selection key for the appliance to be
programmed for 5 seconds.
4. When the key is released, it will start to flash. Enter the
brand code previously identified within 15 seconds (
e.g.
0025
).The selection key flashes more quickly to indicate
that the remote control is ready for the search.
5. Point the remote control towards the appliance. Press
and slowly release the ON/OFF key several times, stopping
when the appliance responds correctly to the command.
6. When the appliance responds correctly, press the OK key
to confirm.Three flashes indicate that the search operation
has been completed correctly.
PHILIPS 0025
5 SEC.
or
N.B. THE LIGHT INDICATOR STOPS FLASHING
The remote control exits programming mode and the light indicator stops flashing:
• if no keys are pressed for 14 seconds
• if an invalid brand code is entered
• if a key other than ON/OFF is accidentally pressed
• if the end of the code search list has been reached. In this case, consult the website
www.meliconi.com/guide
PROGRAMMING USING GLOBAL SEARCH
The quickest and easiest way to programme the remote control is
by consulting the website www.meliconi.com/guide.
Warning: programme one appliance at a time!
ADDITIONAL CHECK
Check that some of the other functions used on your original remote control are working correctly. If the
commands function incorrectly or erratically, you have probably entered a code for a similar remote control
but not the right one. In questo caso ripetete la procedura di ricerca partendo dal punto 2.In this case,
repeat the search procedure starting from point 2.
To display and make a note of the code memorized by means of the search,
follow the instructions described in the paragraph CURRENT CODE DISPLAY.
N.B. THE LIGHT INDICATOR STOPS FLASHING
The remote control exits programming mode and the light indicator stops flashing:
• if no keys are pressed for 14 seconds
• f a key other than ON/OFF is accidentally pressed
• if the end of the code search list has been reached. In this case, consult the website
www.meliconi.com/guide
18
This operation can take up to 20 minutes and should be carried out if you have not succeeded in programming
the remote control by means of the method described above.
1. Switch ON the appliance you wish to program and select
a program.
2. Hold down the selection key for the appliance to be
programmed for 5 seconds.
3. When the key is released, it will start to flash. Enter the
code 0000 within 15 seconds; the selection key flashes
more quickly to indicate that the remote control is ready
for the search.
4. Point the remote control towards the appliance. Press
and slowly release the ON/OFF key several times, stopping
when the appliance responds correctly to the command.
5. When the appliance responds correctly, press the OK key
to confirm. Three flashes indicate that the search operation
has been completed correctly.
5 SEC.
or
19
PROGRAMMING BY INSERTING THE APPLIANCE CODE
N.B. this operation cannot be interrupted and the remote control cannot therefore be used
until the end of the 4 series of flashes.
CURRENT CODE DISPLAY
To find out the code of your remote control, follow this procedure:
If, when consulting the on-line guide at www.meliconi.com/guide, you find the exact code for the appliance
to program the remote control, insert the code as follows:
HOW TO USE THE ADDITIONAL COMMANDS WHICH DO NOT APPEAR ON THE KEYPAD
Find them on your
DIGITAL 2 SMART
remote control by pressing the keys one by one and discovering the
commands that interest you.
In particular, the additional functions most frequently used, such as NORMALIZATION, COLOUR and BRIGHTNESS,
can be found on the following keys:
Although not indicated on the keypad,
some keys can be used for additional commands.
For the functions used less frequently, look for the additional commands on the site
www.meliconi.com/guide. As well as easily finding the code to programme your remote control,
consult the on-line guide to help you to find which keys on the
DIGITAL 2 SMART
.remote control
correspond to the additional commands.
Normalization:
Brightness (+): or green
Brightness (-): or red
Colour (+): or blue
Colour (-): or yellow
1. Hold down the selection key for the appliance to be
programmed for 5 seconds.
2. When the key is released, it will start to flash. Insert the
code within 15 seconds (
e.g.: TV 1100
). Three flashes
indicate that the operation has been completed correctly.
1.Press the select key for which you want to know the code
and hold down for 5 seconds.
2. When the key is released it will start to flash; press and
release the 1-/- key within 8 seconds.
3. After a pause of several seconds, the indicator light
produces four series of flashes with a space between
them, corresponding to the code you are looking for. Count
the number of flashes; each series of flashes corresponds
to one figure in the code. 10 flashes correspond to 0.
4. Make a note of the code on the adhesive label inside the
battery cover for quick and easy future reprogramming.
...................................................... = 1
.......................................... = 3
= 0
....................... = 6
Code obtained = 1306
5 SEC.
or
5 SEC.
or
PROBLEM SOLVING
If you have any queries about your DIGITAL 2 SMART remote control:
• read this Instruction Booklet carefully - you will find an answer to most of your questions
• consult the website www.meliconi.com/guide where you will find the answers you need easily and
quickly.
INFO-LINE
WARRANTY: 2 years
The warranty ceases to be valid if the product is
tampered with or used incorrectly.
Type of remote control GumBody
Remote control model DIGITAL 2 SMART
Purchase date
Dealer’s stamp
The symbol of the crossed trash can shown on the remote control indicates that once the product has reached
the end of its working life it should be disposed of separately from other waste. The user should, therefore, take
the remote control to a specialised collection centre for electronic and electrical waste, or hand it over to the dealer
when purchasing a new similar remote control, on a one to one basis. Correct separated collection for subsequent
recycling, processing and environmentally compatible disposal contributes in preventing possible negative effects
on the environment and on health and favours the recycling of the materials used in producing the remote control.
SOLUTION
Test some other widely used keys. If the problem
persists, check that the batteries are fitted correctly.
If necessary, replace them with 2 new 1.5 V
AAA/LR03 batteries.
Check that the batteries are new and that the remote
control is pointing at the TV without any obstacles
in the way. If required, reset the remote control
code, following the programming procedure.
The batteries are low. Change them.
You may have used the wrong code. Reset the
remote control code, following the programming
procedure.
Follow the programming procedure using the
substitute brand code 0099. Alternatively, to find
the code with which to programme your remote
control consult the on-line guide at
www.meliconi.com/guide
PROBLEM
The appliance does not respond and the light
indicator does not light up when a key is
pressed.
The appliance does not respond but the light
indicator lights up.
The light indicator flashes when a key is held
down but the appliance does not respond.
The remote control commands are not all
working correctly.
The make of your TV is not included in the list
of codes at the end of this booklet.
20
Inhaltsverzeichnis
Andere MELICONI Fernbedienung Handbücher
MELICONI
MELICONI Personal 3 plus Installations- und Betriebshandbuch
MELICONI
MELICONI CONTROL 4 Plus Bedienungsanleitung
MELICONI
MELICONI Control 5 500 PLUS Bedienungsanleitung
MELICONI
MELICONI personal 4 Bedienungsanleitung
MELICONI
MELICONI easytel 2+ Bedienungsanleitung
MELICONI
MELICONI GumBody Universal 5 web Bedienungsanleitung
MELICONI
MELICONI SPEEDY 110 Plus Bedienungsanleitung
MELICONI
MELICONI SPEEDY 2 Bedienungsanleitung
MELICONI
MELICONI Fully 8 RC Bedienungsanleitung
MELICONI
MELICONI easytel TV+ Bedienungsanleitung
MELICONI
MELICONI GumBody Personal 1 Bedienungsanleitung
MELICONI
MELICONI Speedy 100 plus Bedienungsanleitung
MELICONI
MELICONI SPEEDY 210 STB Bedienungsanleitung
MELICONI
MELICONI Universal 2 Bedienungsanleitung
MELICONI
MELICONI FACILE LIGHT Bedienungsanleitung
MELICONI
MELICONI Personal 5+ Bedienungsanleitung
MELICONI
MELICONI FACILE Bedienungsanleitung
MELICONI
MELICONI EASY 300 Bedienungsanleitung
MELICONI
MELICONI CONTROL 3-300 PLUS - WINDOWS Bedienungsanleitung
MELICONI
MELICONI GUMBODY UNIVERSAL 6 LIGHT Bedienungsanleitung
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
