Mercia Garden Products 01DDPENT1408-V3 Gebrauchsanweisung

P 1

14x7 & 14x8 Pressure treated pent shed

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All building’s should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, wood saw, step ladder and drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

Refer to the instructions pages for your specic product code

Pressure Treated Timber

Pressure treating is a chemical process which helps to protect wood against adverse weather which could

lead to rot or insect damage.

The most common chemicals used to pressure treat wood are Alkaline Copper Quaternary (ACQ),

Copper Azole (CA), and Micronized Copper Quaternary (MCQ).

Safety: Always wear gloves, eye protection and a dust mask when handling wood. Due to chemicals in

pressure treated wood, never burn its sawdust or scraps; instead dispose in a landll.

Door Panel QTY 1

AI-01DDPDP2076X2072-V3

Window Panel QTY 1

AI-01DDPWP2076X2072-V3

Plain Panel QTY 2

AI-01DDPPP2076X1774-V3

Gable Right & Left QTY 1 of Each

14x8 - AI-01DDPRG2310X2080-V3

14x8 - AI-01DDPLG2310X2080-V3

14x7 - AI-01DDPLG2016X2080-V3

14x7- AI-01DDPRG2016X2080-V3

Floor QTY 2

14x8 - AI-01DDPF2305X2118-V2

14x7 - AI-01DDPF2118X2012-V2

Door QTY 2

AI-01MBMD551X1742-V2

Roof Sheet QTY 4

14x8 - PI-03-0326

14x7 - PI-03-0327

Strip - 12 x 56 x 2500mm QTY 7

S1256-2500-PT3

Strip - 12 x 30 x 1684mm QTY 6

S1230-1684-PT3

Block - 27 x 44 x 160mm QTY 7

F2744-160-PT3

Roof Support - 14x8: 27 x 44 x 2238mm QTY 7

14x7: 27 x 44 x 1947mm QTY 7

14x8 - F2744-2238-PT3

14x7 - F2744-1947-PT3

Eaves Frame - 28 x 28 x 2132mm QTY 4

FS2828-2132-PT3

T-Hinge QTY 6

PI-07-0021

Turn Button QTY 1

PI-07-0034

Pad Bolt QTY 1

PI-07-0035

Plastic Window Cill QTY 1

PI-08-0013

Styrene - 550x550mm QTY 2

PI-05-0114

Nail Bag

50mm Screw x 80

Felt Tacks x 220

20mm Screw x 23

30mm Black Screw x 1

70mm Screw x54

40mm Screw x 16

30mm Screw x 102

P 2

01DDPENT1408-V3 & 01DDPENT1407-V3

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

14x7 Overall Dimensions:

Length = 4288mm

Width = 2124mm

Height = 2115mm

Base Dimensions:

Length = 4236mm

Width = 2012mm

14x8 Overall Dimensions:

Length = 4288mm

Width = 2415mm

Height = 2115mm

Base Dimensions:

Length = 4236mm

Width = 2305mm

*OSB option only

Fascia - 12x95x2500mm QTY 4

SR1295-2500-PT3

Pre drill

hole

30mm

screw

Pre Assembly

Before assembling remove the transportation

blocks from the bottom of each panel.

Step 1

Place the oor onto a rm and level

base upside down, ensuring the base

has suitable drainage & is free from

areas where standing water can collect.

Secure the oors together using 6x50mm

screws, xing in an alternating pattern

as shown in the illustration.

Once tted, turn the oor assembly the

right way up.

6x50mm Screws

Pre drill

hole

50mm

screw

Cut down to t

Step 2: Door side assembly

Locate the doors(No. 6) into the door panel

(No. 1) and x in place using 3x T-Hinges (No. 13),

securing with 7x30mm screws.

Attach the pad bolt (No. 15) to the centre door

support and the catch to the opposite

door with 10x30mm screws.

Measure between the top and bottom

of the door to the pad bolt and cut 2x (No. 8)

strips to t, secure in place with 2x20mm

screws per strip.

52x30mm Screws

4x20mm Screws

Pre drill

hole

30mm

screw 20mm

screw

17 17

999

Step 3: Window side assembly

Cut 7x(No. 9) strips to 515mm and secure 4x (No. 9)

strips to the inside of the window gap

using 2x20mm screws per strip.

*Ensure the strips are ush with the framing.

Place the plastic cill on top of the board

and rest the styrene in the window gap.

Measure the window gap and cut 1x

strip to t, securing in place with 3x20mm

screws. Attach the remaining 3 (No. 9) strips from

part a using 2x20mm screws per strip.

17x20mm Screws

Cut down to t

Pre drill

hole

30mm

screw

Step 4

Place the right gable (No.4) and the rst

plain side (No. 3)onto the oor and x

together using 3x50mm screws

Do not secure the building to the

oor until the roof is tted.

3x50mm Screws

Pre drill

hole

50mm

screw

*For added weather protection t your

windows using silicone sealant around

the outside edges.

SILICONE

SEALANT

P 3

Please retain product label and instructions for future reference

Step 7

Place the rst three roof support

bars inbetween the front and back

panels, aligning with the central

uprights, x into place by screwing

through the panels into the

roof support bars (xing through

the front and rear panels).

Repeat this process with the

remaining support bars.

*Hint: Use a roof sheet to mark

out the positions for the

remaining roof support bars,

measuring out from the centre.

14x70mm Screws

Pre drill

hole

70mm

screw

Step 8

Attach the 2x eaves frames (No. 12) to

2x roof sheets (No. 7) using 4x30mm

screws pereaves frame.

*Ensure the eaves are ush to the

edges of the roof sheet.

*For T&G roof options use the same

method as stated above ensuring the

eaves framing is ush with the edge

of the roof framing and screwed directly

through the eaves framing into the

roof framing and not into the T&G

boards.

16x40mm Screws

Pre drill

hole

30mm

screw

12 7

P 4

Please retain product label and instructions for future reference

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

*OSB OPTION

*T&G OPTION

Step 5

Following the same method outlined

in step 4, place the next 2 panels onto

the oor and secure in place using

6x50mm screws.

6x50mm Screws

Pre drill

hole

50mm

screw

Step 6

Continue to follow the method

outlined in step 4. Place the

remaining gable and window

panel onto the oor and x using

9x50mm screws.

9x50mm Screws

Pre drill

hole

50mm

screw

*If you have purchased the T&G oor and

roof option please continue to step 8

Step 9

Place the assembled roof panels

on to the building and secure as

shown in the illustration with

16x30mm screws

* Ensure the joints in the roof

sheets sit over the roof bars

and are supported.

16x30mm Screws

Pre drill

hole

30mm

screw

Step 10

Secure the building to the

oor using 28x50mm screws.

*Ensure to screw through the framing

into the oor bearers.

28x50mm Screws

Pre drill

hole

50mm

screw

Step 11

Cut the felt into 3 sheets and lay

onto the roof.

* Ensure there is approximately

50mm of overhang around the

building.

Fix into place using 219x felt tacks

at 100mm intervals.

219xFelt Tacks

Felt

tacks

Felt size: 4390mm

Step 12

Measure the side of the roof,

cut 2x (No.18) facias to size and x in

place using 3x30mm screws.

Measure the distance between

the 2 facias at the front of the

building & cut 2x (No. 18) facias to match

the gap. Secure to the building

using 6x30mm screws.

12x30mm Screws

Cut down to t

Pre drill

hole

30mm

screw

*If you have purchased the T&G roof and oor option ensure to x the roof to

the building using 35x70mm screws following the same method outlined

above.

Internally: Secure the roof panels together where they join using 5x50mm screws.

35x70mm Screws

5x50mm Screws

Pre drill

hole

70mm

screw 50mm

screw

P 5

Please retain product label and instructions for future reference

HANDLE

WITH CARE

Step 13

Measure the gaps at the

corners of the building &

cut 6x (No. 8) strips to match.

Once cut secure to the

building using 3x30mm

screws per strip.

18x30mm Screws

Cut down to t

Pre drill

hole

30mm

screw

Step 14

Fix the last roof block to the inside

of the left door at the top. Screw

through the front of the door into

the block using 2x30mm screws.

*Ensure the block sits below the

door head.

Secure the turn button to the block

with 1x30mm black screw. Making

sure the turn button catches on the

door head.

2x30mm Screws

1x30mm Black Screws

Pre drill

hole

30mm

screw

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

AFTER TREATMENT:

score around protective

cover on glazing and

carefuly peel

covering back

P 6

Please retain product label and instructions for future reference

P 7

Please retain product label and instructions for future reference

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01OVLPA0510PB-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0634RANE0504FGDD2TW1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01RAW2010DDOW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG173SG-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTOVRA0604SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHPN0806PA-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02RSE0505-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0644LOG208-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628LOG114-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0644CSNE0303HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OSBA0705SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0705SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA1008DDFW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products OIDTOVRA1006SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products SI-002-001-0022 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products OSB APEX Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03WES1008-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products BOURNEMOUTH 03BRN0807-V4 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01GRO1008DD-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01GRO1006DD-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTSHPMOW4803-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634AXNE0503HGDD2MW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTOVAX10DDNWGP-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03WES1008-V1 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung