Mercia Garden Products 01PTOSBA1008DDFW-V2 Gebrauchsanweisung

10X8 PRESSURE TREATED OSB APEX

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All building’s should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips

screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can

be helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm

sunshine and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to

prevent the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof

treatment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm

above the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

Refer to the instructions pages for your specic product code

01PTOSBA1008DDFW-V2

Pressure Treated Timber

Pressure treating is a chemical process which helps to protect wood against adverse weather which could

lead to rot or insect damage.

The most common chemicals used to pressure treat wood are Alkaline Copper Quaternary (ACQ),

Copper Azole (CA), and Micronized Copper Quaternary (MCQ).

Safety: Always wear gloves, eye protection and a dust mask when handling wood. Due to chemicals in

pressure treated wood, never burn its sawdust or scraps; instead dispose in a landll.

P 10

01PTOSBA1008DDFW-V2

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Overall Dimensions:

Length = 3028mm

Width = 2484mm

Height = 2121mm

Base Dimensions:

Length = 3016mm

Width = 2414mm

Building content

Door Gable

AI-01PTSHPDG2310X2094-V2 Back Gable

AI-01PTSHPPG2310X2094-V2

Plain Side

Qty 2

AI-01PTSHPPS1490X1567-V2

Window Panel Qty 2

AI-01PTSHPWS1490X1567-V2

Floor

Qty 2

AI-01PTOSBF2360X1487-V2

Roof Qty 8

PI-03-0224

Door

Qty 2

AI-01PTMBDS1660X439-V2

1234567

T Hinge Qty 4

PI-02-1043

Felt

PI-01-0003

21 23

L-Bracket

Qty 2

PI-07-0012

Ridge Bar - 27x70x1462mm Qty 2 - F2770-1462-PT3

Truss Frame - 27x44x1262mm Qty 6 - F2744-G-1302-PT3

Eaves Frame - 28x28x1001mm Qty 6 - FS2828-1001-PT3

Truss Block - 27x44x140mm Qty 6 - F2744-G-160-PT3

Door Block - 28x28x140mm Qty 2 - FS2828-140-PT3

Fascia - 12x60x1333mm Qty 4 - S1260-1333-PT3

Door Strip - 12x60x1016mm Qty 1 - S1260-1016-PT3

Door Strip - 12x60x530mm Qty 1 - S1260-530-PT3

Cover Trim - 12x45x1575mm Qty 6 - S1245-1575-PT3

Window Strip - 12x30x546mm Qty 10 - S1230-546-PT3

Door Beading Strip - 12x28x1590mm Qty 2 - S1228-1590-PT3

Finial

Qty 2

DIAMOND SHED FINIAL

Truss Support - 27x44x450mm Qty 3 - F2744-G-490-PT3

Plastic Window Cill

PI-08-0013

Turn Button

Qty 3

PI-07-0034

Styrene

Qty 4

PI-05-0114

U Channel

PI-07-0013

Nail Bag

30mm Screw x 130

30mm Black Screw x 3

50mm Screw x 80

40mm Screw x 136

Felt Tacks x 120

Remove transportation

blocks from the bottom

of each panel before

beginning assembly. Each

Panel should have two

blocks.

Pre Assembly

Fix the T Hinges onto the

doors and door frame as

shown. Ensure that the

screws go through the

cladding and into the

framing behind.

28x30mm screws

30mm

screw Pre drill

hole

P 11

Step 1

12x40mm screws

Place oor on rm and level base, ensure

base has suitable drainage free from areas

where water can collect. (See front page on

base requirements).

Attach the oors using 12 x 40mm screws

40mm

screw Pre drill

hole

Fix the corners with 50mm

screws as shown in diagram.

Position the panels so there is equal spacing

between the oor and cladding on all 4 sides

Step 2

3x50mm Screws

50mm

screw Pre drill

hole

Step 3

Fix the remaining plain side and

a window side at the corners

with 50mm screws as shown in

diagram.

6x50mm Screws

50mm

screw Pre drill

hole

Step 4

Fix the remaining window side

and the door gable at the

corners with 50mm screws as

shown in diagram.

9x50mm Screws

50mm

screw Pre drill

hole

P 12

Step 5

Ridge Bar Assembly

Position the two parts of the ridge

bar within the ‘U’channel and

secure from either side with 3 x

30mm screws and 4 x 30mm screws

from underneath. Secure an‘L’

bracket to either end of the ridge

bar using 2 x 30mm screws per

bracket.

18x30mm Screws

26 8

23 23

Place the roof support bar in

between the front and back panels.

Ensure the top corners of the

support bar are ush with each top

point. Secure in place using the L

Bracket on each end with 4x30mm

screws.

30mm

screw Pre drill

hole

Step 6

i)Position a truss frame to the ridge

bar sloping down towards the

building side, ensure it is central to

the middle upright of the panel. Fix

with a 50mm screw through the

ridge bar into the truss frame.

ii) Align the second truss frame with

the rst on the opposite side of the

ridge bar and x with a 50mm

screw at an angle as illustrated.

ENSURE SUPPORT BARS

ARE MANUALLY SUP-

PORTED UNTIL FIXED AT

BOTH ENDS

iii

2x50mm Screws

50mm

screw Pre drill

hole

Step 7

i) Fix the truss block to the side

panel framing with 2 x 50mm

screws. Position the block at the

top of the framing with the

angle pointing upwards into the

building, aligning the block

centrally along the join between

the side panels with one screw

in each panel.

ii) Fix the support bar to the

block using 1 x 50mm screw.

6x50mm Screws

50mm

screw Pre drill

hole

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

Step 8

Fix a Truss support between the

two truss frames and x in place

using 40mm screws, ensure you

pre-drill holes before xing

together.

4x40mm Screws

40mm

screw Pre drill

hole

P 13

Step 9

Place two roof sheets ontop of the

plain gable and truss making sure

the roof sheet sits ush to the

outside edge of the plain gable

and x using 40mm screws. Before

xing the roof sheet to the truss

frame make sure the edge of the

roof sheet sits in the middle of the

truss frame then x using 40mm

screws.

20x40mm Screws

6x30mm Screws

Fix the eaves frame to the

roof sheet using 3x30mm

screws for each sheet.

Step 10

Attach another truss in the

centre of the building the

same way as shown in step

6 through to 8.

8x50mm Screws 9

4x40mm Screws

Step 11

Attach another two roof sheets ontop of

the two truss’s in the same way as stated

in step 9a ensuring that the roof sheets

sits half way onto each truss frame.

20x40mm Screws

Attach another truss in the

centre of the building the

same way as shown in step

6 through to 8.

Attach another two roof

sheets ontop of the two

truss’s in the same way

as stated in step 9a

ensuring that the roof

sheets sits half way onto

each truss frame.

20x40mm Screws

8x50mm Screws

4x40mm Screws

40mm

screw Pre drill

hole

40mm

screw Pre drill

hole

50mm

screw Pre drill

hole

40mm

screw Pre drill

hole

P 14

Step 11 con...

Attach another roof sheet ontop of the

truss in the same way as stated in step

9a usig 20x40mm screws.

Then x the eaves frame to the roof

using 3x30mm screws on each eave.

20x40mm Screws

6x30mm Screws

Fix the nal eaves frame to the roof

sheet using 3x30mm screws for each

sheet.

12x30mm Screws

40mm

screw Pre drill

hole

30mm

screw Pre drill

hole

30mm

screw Pre drill

hole

Step 12

Once the roof is xed

attatch the building

to the oor with 50

mm screws.

24 x 50mm Screws

50mm

screw Pre drill

hole

P 15

Step 13

132 x Tacks

Cut out three strips of

3204mm felt and place

onto the roof.

Place the felt at onto the

roof in the order that is

stated on the diagram

below.

Once the sheets are laid out

x them onto the roof with

tacks 100mm apart.

HANDLE

WITH CARE

Step 14

Fit the cover trims to the

building and secure in place

with 40mm screws as

shown.

Pre drill to avoid splitting.

18x40mm Screws 16

40mm

screw Pre drill

hole

Step 15

16x40mm Screws

Attatch faisca’s to the roof

leaving a slight overhang at

the top..

Fit the fascias to the roof

over the felt and secure in

place with 40mm screws as

shown.

Pre drill to avoid splitting.

20 13

40mm

screw Pre drill

hole

P 16

Step 15

Use 4x30mm Screws to x

each beading strip onto the

door gable. Ensure that the

screw is parallel with the

door frame when xing the

strip to the door gable as

shown in the close up view.

Attatch the turn button to

the top and bottom door

blocks with 1x30mm screw

for each one.

First line up the door blocks

on top of the framing of the

doors. Then x with

2x30mm screws by screwing

through the matchboard

door into the block.

8x30mm Screws

2x30mm Black Screws

6x30mm Screws

30mm

screw

Pre drill

hole

30mm

screw

Step 16

Fix the door strips to the

master door using 5x30mm

screws.

If the strips are attatched to

the slave door the doors will

not open properly.

5x30mm Screws

Use 1x30mm screw to

secure the turn button to

the master door.

These turn buttons help to

keep your doors straight

during high and low

moisture levels in the

atmosphere.

1x30mm Black Screws

30mm

screw

Pre drill

hole

30mm

screw

P 17

Step 17

Fix 2x window strips to the framing along

the outside edge of the window gap using

3x30mm screws per strip.

Place the plastic cill into the window

panel as shown in the illustration.

Fit the styrene sheets on top of the

window cill.

*For added weather protection t your

windows using silicone sealant around

the outside edges.

**When positioning the styrene sheets ensure

there is an equal distance on all sides.

Attach the remaining 3x window strips

to either side of the windows and the

centre. Secure into place using 3x30mm

screws per strip.

15x30mm Screws

Pre drill

hole

30mm

screw

Side View

SILICONE

SEALANT

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

AFTER TREATMENT:

score around protective

cover on glazing and

carefuly peel

covering back

Styrene

Window Cill

P 18

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1208DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG016-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0406DDNW-V Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02PLAY511511-V2-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products SI-002-001-0022 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 04GREENLEAN0804-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04GREEN0606SD-V5 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPA0806SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products ESDXL21PT001 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01SHPWOR1610DDOW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03PTMBPN0406STP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1208DDOP-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02SNO0705-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01SHPSTR0402-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG015-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OSBP1006SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0634CSNE0404HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02HIDE0705-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 10DTSHPN0804-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products ESDXL21PT002 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products POPPY PLAYHOUSE Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634RARE0302ND1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01RAW2010DDOW-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03VER0808-V2 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung