Mercia Garden Products 01DTSHAX0608SDFW-V1 Gebrauchsanweisung

ANTI-ROT

GUARANTEE TODAY

PLEASE SCAN HERE:

**Protim Aquatan T5 (621)**

Your building has been dip treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building has been treated by the

correct application of Aquatan solution and then allowed to dry.

Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

Measure

under the

head

Measure

overall

length

Screws & Nails Bolts To identify the

xings required

for each step use a

measuring tape.

01DTSHAX0608SDFW-V1

DIP TREATED SHIPLAP APEX 6FT X 8FT SINGLE DOOR FIXED WINDOW

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

For ease of assembly, you

will need a tape measure to

check dimensions of

components.

P 1

Please retain product label and instructions for future reference

General Instructions

P 2

01DTSHAX0608SDFW-V1

Overall Dimensions:

Width = 2494mm

Depth = 2132mm

Height = 2278mm

Base Dimensions:

Width = 2350mm

Depth = 1753mm

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Side Panel QTY 2

AI-S11SHPP1758X1717-V1

Back Panel QTY 2

AI-S11SHPPTF1150X1669-V1

Window Panel QTY 2

AI-01S11SH1SFW809X1669-V1

Floor QTY 2

AI-R11MBF1175X1753-V1

Roof QTY 2

AI-S11MBOHAR2084X1345-V1

8910

Door QTY 1

AI-S21FBMBZBD676X1770-V1

Door Gable Top Right QTY 1

AI-S11SHHASDGTR1500X567-V1

Door Gable Top Left QTY 1

AI-S11SHHASDGTL1150X567-V1

Plain Gable Top Right QTY 1

AI-S11SHAGTR1550X567-V1

Plain Gable Top Left QTY 1

AI-S11SHAGTL1550X567-V1

Ridge Bar 27x70x1702mm QTY 1

F2770-1702mm

Fascia 12x95x1365mm QTY 4

S1295-G-1365mm

Gable Cover Trims 12x28x610mm QTY 4

S1228-610mm

Ridge Bar Support 27x44x676mm QTY 2

F2744-G-716mm

Door Beading Strip 12x28x1716mm QTY 2

S1228-1716mm

Door Framing 28x28x682mm QTY 1

FS2828-682mm

Cover Trims 12x40x1712mm QTY 5

S1240-1712mm

Cover Trim 12x40x430mm QTY 2

S1240-430mm

Front Weatherboard 1614mm QTY 1

WB-1614mm

Back Weatherboard 2090mm QTY 1

WB-2090mm

P 3

Please retain product label and instructions for future reference

Window QTY 2

AI-FW496X574-V1

21 22 23 24

25 26 27 28

Window Blocks QTY 8

PI-07-0011

Shed Finial QTY 2

SHED DIAMOND FINIAL

Felt QTY 1

PI-01-0016

Corner Brace

QTY 2

PI-07-0012

T Hinge QTY 3

PI-02-1042

Turn Button QTY 2

PI-07-0034

Pad Bolt QTY 1

PI-07-0035

Nail Bag

There may be extra screws present in the nail bag

50mm Screw x 76

40mm Screw x 16

30mm Screw x 130

60mm Screw x 10

Felt Tacks x 90

Pre Assembly

Before assembling remove the transportation

blocks from the bottom of each panel.

Take care removing the blocks as to not damage

the panels. Tap with a at headed screwdriver

and hammer.

Dispose of the blocks once removed.

Pre drill

hole

IMPORTANT: Pre-drill before xing screws.

Step 1

Parts needed - No. 10 QTY 2

Place the oor panels (No.10) onto a rm

and level base. Ensure the base has suitable

drainage, free from areas where standing

water can collect.

Secure the oors together using 10x50mm

screws through the oor bearers in an

alternating pattern.

10x50mm Screws

50mm

screw

P 4

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

Please retain product label and instructions for future reference

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 2

Parts Needed- No. 1 QTY 1

- No. 9 QTY 1

Place the Side panel (No.1) and the Back

Panel (No.9) onto the oor. Fix at the corner

using 3x50mm screws.

Do not secure the building to the oor

until the roof has been tted.

Position the panels so there is equal spacing

between the oor and cladding on all sides.

The side panels should sit higher than the

Back panels

3x50mm Screws

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 3

Parts Needed- No. 1 QTY 1

- No. 9 QTY 1

Fix the end of the Back Panel (No.9) to the

already standing back panel with 3x50mm

screws in an alternating pattern as shown in

the illustration.

Fix the corners of the Side Panel (No.1) to the

newly standing Back Panel with 3x50mm

screws per panel.

Do not secure the building to the oor

until the roof has been tted.

Position the panels so there is equal

spacing between the oor and cladding on

all sides.

6x50mm Screws

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 4

Parts Needed- No. 2 QTY 2

Place the Window panels (No.2) onto the

oor, x the corners using 3x50mm screws.

Do not secure the building to the oor

until the roof has been tted.

Position the panels so there is equal

spacing between the oor and cladding on

all sides.

The Front panels should sit lower than the Side

panels

6x50mm Screws

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

50mm

screw

Step 5

Parts Needed- No. 15 QTY 1

Place the Door Framing (No.15) onto the

oor, between the Front Window Panels.

Ensure the framing is ush to the Window

Panel framing.

Ensure that the panels are all equally

spaced to the oor before xing the door

framing.

Secure the Door framing to the oor using

3x50mm screws

3x50mm Screws

P 5

Please retain product label and instructions for future reference

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 8

Place the assembled Plain Gable Tops

(No.5 & 6) on top of the Back panels. Fix

using 6x50mm screws in an alternating

pattern, going through the gable framing

and into the panel framing below.

Place the assembled Door gable tops (No.3

& 4) on top of the Front Window Panels. Fix

using 4x50mm screws per side.

Ensure Cladding is tted correctly and

ush to the panels before securing.

14x50mm Screws

Pre drill

hole

30mm

screw

Step 9

Parts Needed- No. 11 QTY 1

- No. 24 QTY 2

Place the Ridge Bar (No.11) on top of the

Roof Bar Supports (No.12) inbetween and

in line with the central framing of the

gable tops.

Fix the Ridge Bar (No.11) to the Roof Bar

Supports (No.12) using one Corner Brace

(No.24) for each end as shown in the

diagram. Fix with 4x30mm screws each.

8x30mm Screws

IMPORTANT: Pre-drill before xing screws.

11 24

50mm

screw

Step 6

Parts Needed - No. 3 QTY 1

No. 4 QTY 1

No. 5 QTY 1

No. 6 QTY 1

Place the Door Gable Top Right and

the Door Gable Top Left (No.3 & 4)

together. Then place the Plain Gable

Top Right and the Plain Gable Top Left

(No.5 & 6) together.

Making sure that both sets of gable

tops meet level, x together in the

middle using 3x50mm screws. Stag-

ger the screws so they do not collide

as shown in the illustration.

6x50mm Screws

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

50mm

screw

Step 7

Parts Needed- No. 12 QTY 2

Attach the Roof Bar Supports (No.12)

to the assembled gables using

6x50mm screws to complete the

gable assemblies. Make sure that the

angled edges of the Ridge Bar Sup-

port are ush with the edges of the

outer framing as shown in the

diagram.

The roof bar support should be

parallel with the door opening or

bottom edge of the assembled

gables.

6x50mm Screws

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

P 6

Please retain product label and instructions for future reference

IMPORTANT: Pre-drill before xing screws.

40mm

screw

Pre drill

hole

Step 11

Parts needed - No. 7 QTY 2

Place the Roof Panels (No. 7) on top of the

building making sure the framing in the roof

panels sits rmly within the Gable Tops (No.3,

4, 5 & 6) and on top of the Ridge Bar (No.11).

**Make sure that you have got the roof

panels the correct way round with the recess

at the top of the apex as shown in the

diagram.**

**The edges of the roof panels must be ush

with the outer cladding of the Rear Plain

Gable Top (No.5 & 6).**

From the top, x directly through the roof

panels (No.7) and into the ridge bar (No.11)

the below using 5x60mm screws per roof

panel.

It is essential that the ridge bar (No.11) and

roof panel (No.7) framing pull together when

xed with 60mm screws. You may require

another person pushing the ridge bar (No.11)

up from below to achieve this.

HINT - Follow the nailing line of the framing on

the roof panel so that you are more likely to x

into the ridge bar below.

Fix the remaining sides of the roof panels using

40mm screws, ensuring to go through to the

framing below.

16x40mm Screws

10x60mm Screws

60mm

screw

30mm

screw

Step 10

Parts Needed - No. 19 QTY 1

No. 20 QTY 1

Place the Front Weatherboard (No.19)

with the bottom edge ush with the

top of the door opening. Fix to the

framing using 9x30mm screws.

Place the Back Weatherboard (No.20)

with the bottom edge ush with the

underside of framing of the Back

Panel. Fix to the framing using

9x30mm screws.

18x30mm Screws

Pre drill

hole

IMPORTANT: Pre-drill before xing screws.

P 7

Please retain product label and instructions for future reference

50mm

screw

Pre drill

hole

Step 12

Once the roof is xed, attach the build-

ing to the Floor with 50mm screws.

Ensure the screws go through the panel

into the Floor framing

22x50mm Screws

IMPORTANT: Pre-drill before xing screws.

Felt

tacks

27 27

Step 13

Parts needed - No. 27 QTY 1

Cut the felt (No. 27) into three sheets at

2200mm. Lay the sheets onto the roof

as shown in diagram ensuring there is a

50mm overhang around the sides.

Apply the felt tacks with a 100mm space

per tack..

90x Felt Tacks

HANDLE

WITH CARE

Please retain product label and instructions for future reference

P 8

IMPORTANT: Pre-drill before xing screws.

Step 14

Parts Needed- No. 25 QTY 8

- No. 28 QTY 2

Fix two Window Blocks (No. 25) to the sides

(internally) of the Window (No.28) as shown

with 1x30mm screw per block in the illustra-

tion.

4 Window blocks should be used per window

with 2 per side.

Place the Windows into the window opening

within the Window Panels and x by screwing

though the Window Block (No.25) into the

framing using 2x30mm screws per block, as

shown in the illustration.

24x30mm screws.

Pre drill

hole

30mm

screw

Step 15

Parts needed - No. 8 QTY 1

No. 21 QTY 3

Place the door (No. 8) within the

door aperture opening. Fix the T Hinges

(No.21) onto the door and Window

Panel as shown (taking into account

on which side of the Window Panel

opening you want the Door to open).

Ensure that the screws go through the

cladding and into the framing behind.

21x30mm Screws

Pre drill

hole

30mm

screw

**PLEASE NOTE** Before tting the

hinges, ensure the door is in the correct

position depending on which side you

want the door to open. See external

illustrations below which show the doors

internal framing.

Opens from the Left Opens from the Right

IMPORTANT: Pre-drill before xing screws.

P 9

Please retain product label and instructions for future reference

Step 17

Parts needed - No. 17 QTY 5

No. 18 QTY 2

Fit the Cover Trims (No. 17 & 18) over

each panel join and corner of the building

as shown in the illustration using 30mm

screws. Pre drill to avoid splitting.

15x30mm Screws

30mm

screw

Pre drill

hole

18 1717

Use 4x30mm Screws to x each Door

Beading Strip (No. 16) onto the

insides of the door aperture opening.

Ensure that the screw is parallel with

the framing when xing the strips to

the Panels as shown in the close up

view.

8x30mm Screws

Step 16

Parts needed - No. 16 QTY 2

30mm

screw

Pre drill

hole

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

30mm

screw *Cut down

trims to t

14 14

Step 18

Parts Needed- No.14 QTY 4

Fix the Gable Cover Trims (No.14) to

the building with 2x30mm screws

per Trim.

The Gable Cover Trims will need to

be cut to t the angle.

8x30mm screws.

IMPORTANT: Pre-drill before xing screws.

P 10

Please retain product label and instructions for future reference

Pre drill

hole

30mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 19

Parts Needed- No. 13 QTY 4

- No. 26 QTY 2

Fix the Fascia (No.13) to each end of

the roof, securing with 3x30mm

screws per Fascia. Ensure the screws

go through the roof framing

Fix the Diamond Finials (No.26) to

the Fascias using 2x30mm screws per

nial.

16x30mm Screws.

12x30mm screws

Fix the Pad Bolt (No.22) with 6x30mm

Screws to the horizontal brace to the

door.

Then x the pad bolt retainer to the

Window Panel framing using 4x30mm

Screws

Fix the two turn buttons (No.23) to the

Window Panel at the top and bottom of

the door using the 30mm screws.

Step 20

Parts Needed- No. 22 QTY 1

- No. 23 QTY 2

Pre drill

hole

30mm

screw

IMPORTANT: Pre-drill before xing screws.

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 0628RASH0302FBSDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0806SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1206DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 010VLPA0305SDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03TGCORSE0409-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OAOSB0702PB-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHPN0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTGRODB1008-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03HEL1010DDFW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03OVLPBRN0705-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0705SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVRA1006SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHOSBRAX0705SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products Wessex 03WES1208-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0705SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products BOURNEMOUTH 03BRN0707-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619PNSH1227FBSD-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products GROUNDSMAN 10 X 8 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTOVPN0806SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OSBA0707DDSW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619LOG018-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628AXNE0403HGDD1SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTOVRA0604SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 06LOG004-V1 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung