Mercia Garden Products 0634LOG249-V4 Gebrauchsanweisung

P 1

0634LOG249-V4 (5x4m)

0634LOG249-V4: 5x4m Reverse apex cabin (34mm)

2mm Drill bit

Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied)

including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm

bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions.

For the duration of heavy or extended periods of rain, swelling of the wood panels may

occur. Warping of the wood may also occur during excessive dry spells due to an interior

moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is

suggested that the outdoor building is sprayed with water during extended periods of

warm sunshine and sheltered as much as possible during rain or snow.

BUILDING A BASE

When thinking about where the building and base are going to be constructed:

Ensure that there will be access (60cm) to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to

diagrams for the base dimensions. The base should be slightly smaller than the external

measurement of the building, i.e. The cladding should overlap the base, creating a run

o for water. It is also recommended that the oor be at least 25mm above the

surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in

the case of childrens products independently tested to EN71 level, we cannot accept

responsibility for your safety whilst erecting or using this product.

Refer to the instructions pages for your specic product code

For ease of assembly use a

rubber mallet to t the log

boards. Do NOT use a heavy

hammer.

Ensure to measure and check before cutting

boards.

It is advisable to use a hand

saw when cutting roof and

oor boards.

To ensure log boards are even, use a spirit

level to check each layer has been installed

correctly.

Felt

Double Door Pack*

P 2

Please retain product label and instructions for future reference

0634LOG249-V4

Overall Dimensions:

Width = 5040mm

Depth = 4140mm

Height = 2724mm

Base Dimensions:

Width = 4808mm

Depth = 3808mm

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Short Window Pack*

QTY 2

Log 249 Gable - 4000mm

QTY 2

Starter Board - 34x66x5000mm QTY 2

LB34RT66-A-5000

Log Board - 34x120x4000mm QTY 25

LB34-A-4000

Log Board - 34x120x893mm QTY 30

LB34-B-893

Log Board - 34x120x2535mm QTY 6

LB34-B-2535

Log Board - 34x120x893mm QTY 12

LB34-C-893

Log Board - 34x120x1625mm QTY 24

LB34-B-1625

Log Board - 34x120x5000mm QTY 19

LB34-A-5000

Log Board - 34x45x5000mm QTY 2

LB34RG45-A-5000

Roof Board - 16x121x2114mm QTY 90

MB16-C-2114

Floor Board - 16x121x3739mm QTY 43

MB16-C-3739

Bearer - 44x58x3808mm QTY 2

F4458-3808-PT

Bearer - 44x58x4692mm QTY 14

F4458-4692-PT

Purlin - 45x120x5004mm QTY 3

F45120-A-5004

Eaves Frame - 27x44x2502mm QTY 4

F2744-2502

Fascia - 16x120x2118mm QTY 4

S16120-2118 (Angled)

Fascia - 16x120x2520mm QTY 4

S16120-2520

Storm Brace - 27x44x2000mm QTY 8

F2744-2000

Log Board - 34x120x5000mm

LB34-AD-5000

Log Board - 34x120x4000mm

LB34-AD-4000

*All components for the Windows and Doors are

shown in the Windows and Doors instruction

packs.

Closure Trim - 16x28x2400mm (approx length) QTY 16

S1628-2400

Roof Spacers QTY 5

PI-07-0208 (20x100x2mm)

Pre-assembly

*Please note:

Each board interlocks at

either end in a staggered pattern.

Before securing ensure that the boards

are tted properly in their respective

tongues and grooves.

P 3

Please retain product label and instructions for future reference

Felt Tacks x600

70mm Screw x80

40mm Screw x674

30mm Screw x 96

80mm Bolt Set x16

Nail Bag

Pre drill

hole

70mm

screw

Step 1

Parts needed - No. 16 QTY 2

No. 17 QTY 14

Lay the Bearers (No. 16

& No. 17 ) onto a rm and level

surface (free from areas

where standing water can

collect) as shown in the

illustration.

Fix the framing together at

each corner using 8x70mm

screws, ensuring the frame is

ush.

8x70mm Screws

Example picture

2 screws per bearer per end

P 4

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

Please retain product label and instructions for future reference

17 17 17 17 17 17 17 17 17 17 17

Pre drill

hole

70mm

screw

Following the same

method arrange the remaining

framing (No. 17) inside the

assembled frame.

*Ensure there is an equal

amount of space between each

frame.

Secure each of the frames in

place using 2x70mm screws for

each side of the bearer, ensuring

the framing remains level.

48x70mm Screws

Pre drill

hole

70mm

screw

Step 2 (See Pre-Assembly)

Parts needed - No. 4 QTY 2

No. 5 QTY 2

Place the boards (No. 4 & 5) on

to the assembled base frame

along the longest sides.

*Ensure the notches at either

end of each board are ush

and level with the ends of the

frame.

Fix each of the starter boards to

the frame by screwing through

the notch into the frame as

shown in the illustration.

4x70mm Screws

IMPORTANT: Pre-drill before xing screws.

Please Note: The short boards at the

front of the building (either side of

the door and window opening’s)

can be placed either side depending

on your needs.

P 5

Please retain product label and instructions for future reference

Step 3 (See Pre-Assembly)

Parts needed - No. 5 QTY 10

No. 6 QTY 6

No. 7 QTY 6

No. 10 QTY 6

Following the same method

outlined in Pre-Assembly, lay

the rst 6 boards (No’s. 5, 6,

7 & 10) onto the starter boards

to create your rst level.

*Ensure that the boards are

level and ush with each

other as you lay each one.

IMPORTANT: Pre-drill before xing screws. Step 4

Once you have laid 6 log boards (o

of the starter) up the door section,

slide the assembled door frame (No.

2) assembly over the boards resting

the frame on top of the starter board.

*Please note: This image is for

illustrative purposes and may dier

from your choice in product (regard-

ing door position). Nevertheless the

process of tting the door frame is

the same.

**Please Note: The short boards at

the

front of the building (either side of

the door and window opening’s) can

be placed either side depending on

your needs.

P 6

Please retain product label and instructions for future reference

Step 5 (See Pre-Assembly)

Parts needed - No. 5 QTY 7

No. 6 QTY 12

No. 8 QTY 6

No. 9 QTY 12

No. 10 QTY 6

Following the same method

outlined in Pre-Assembly, lay

the next 6 boards (No’s. 5, 6, 8,

9 & 10) onto the assembly to

create your second level.

*Ensure that the boards are

level and ush with each

other as you lay each one.

*Doors can be hung once the

boarding has enclosed the

door frame by 12-13 boards,

refer to door installation

instructions, if not, you can

install the door at step 7. ***Please Note: The short boards placed

to create the opening’s for the doors &

windows can be placed either side

depending on your needs.

IMPORTANT: Pre-drill before xing screws. Step 6

Once you have laid the second

level of boards onto the assembly

slide the window(s) (No. 1) between the

smaller boards and rest on to the

longer board.

*Ensure the boards are level with

each end.

*Please note: This image is for

illustrative purposes and may

dier from your choice in product

(regarding window position ).

Nevertheless the process of tting

the window is the same.

P 7

Please retain product label and instructions for future reference

10 5

Step 7 (See Pre-Assembly)

Parts needed - No. 5 QTY 6

No. 6 QTY 12

No. 8 QTY 6

No. 9 QTY 12

No. 10 QTY 6

Following the same method

outlined in Pre-Assembly, lay

the remaining boards (No’s.

5, 6, 8, 9 & 10) onto the

assembly to bring the board

level to the top of the

window and door frames.

*Ensure that the boards are

level and ush with each

other as you lay each one.

*Doors can be hung once the

boarding has enclosed the

door frame.

IMPORTANT: Pre-drill before xing screws.

Step 8 (See Pre-Assembly)

Parts needed - No. 5 QTY 1

No. 10 QTY 1

No. 12 QTY 1

No. 13 QTY 1

Following the same method

outlined in Pre-Assembly, lay

the last boards (No’s. 5, 10, 12

& 13).

*Ensure that the boards are

level and ush with each

other as you lay each one.

Step 9 (See Pre-Assembly)

Parts needed - No. 3 QTY 2

Place the gable tops (No. 3)

onto the assembly. Fix into

position by screwing

through the notches as

shown in the illustration.

*Ensure that the boards are

level and ush with each

other as you lay each one.

4x70mm Screws

Pre drill

hole

70mm

screw

IMPORTANT: Pre-drill before xing screws.

P 8

Please retain product label and instructions for future reference

Step 10 (See Pre-Assembly)

Parts needed - No. 11 QTY 2

Place the last two boards

(No. 11) onto the building.

Secure into position at

either end by screwing

through the notch into the

board below.

*Ensure that the boards are

level and ush with each

other as you lay each one.

**Ensure to stagger the

screws so as not to collide

with the previous screw.

4x70mm Screws

Pre drill

hole

70mm

screw

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

Step 11

Parts needed - No. 18 QTY 3

Align the Roof Purlin(s) (No.

18) into the cut out slots on each

gable top ensuring each roof purlin

interlocks the boards.

Secure the roof purlins at

each end by screwing through the

purlins into the boards (ensure to

pre-drill to avoid the boards

splitting) using 4x70mm screws per

roof purlin.

*Please note: The gable shown is for

illustrative purposes and may dier

in width from your choice in

product.

Nevertheless, despite any

dierences

the process of xing the roof purlins

is the same.

70mm

screw

P 9

Please retain product label and instructions for future reference

Step 12

Parts needed - No. 14 QTY 90

Place the rst two roof

boards (No. 14) onto the assembly

on each side, making sure the

boards are ush to the end of the

roof purlin. Once in position x to

each purlin using 3x40mm screws.

Due to natural occurences of wood

shrinkage / expansion. You maybe

required to use the provided spac-

ers and place a space of 2mm to

ensure every roof board lines up

with the truss’.

*Ensure the roof boards meet

at the top of the apex and leave

an overhang at the bottom.

Continue adding the roof boards

along the roof, xing each one into

position using 3x40mm screws,

making sure that each board is

interlocked, ush at the bottom &

meet at the top of the apex.

The last board on each side

will overhang: Using a staight edge

and a pencil mark out a line as

a guide.

Cut along the pencil mark and

remove the excess. Place the

cut down boards back onto the

roof and secure into place

using 3x40mm screws per

board.

*Please Note: This image is for

illustrative purposes and may dier

from your choice in product.

Nevertheless the process of cutting

and tting the last roof boards is the

same.

270x40mm Screws

40mm

screw

Pre drill

hole

*Cut to t

23b 14

Step 13

Parts needed - No. 19 QTY 4

Ensuring the roof boards are

ush at the overhanging side and

meet at the apex, x the Eaves

Frames (No. 19 ) to the underside

of the roof boards using 9x40mm

screws as shown in the

illustration.

*Please Note: This image is for

illustrative purposes and may

dier from your choice in product.

Nevertheless the process of xing

the eaves frames is the same.

36x40mm Screws

40mm

screw

Pre drill

hole

P 10

Please retain product label and instructions for future reference

Front

Side

Step 14

Parts neeeded - No. 15 QTY 43

Place the rst oor board (No. 15)

inside the building ush to the log

board on one side. Continue adding

the oor boards (internally) making

sure to interlock each individual board.

*Do NOT secure the boards until

the last board has been measured

and cut.

Following the same method as before

measure the gap between the bottom

of the tongue (on the last board placed)

and the log board.

Using a straight edge mark out the

measurement onto the last oor board

(No. 15) and cut along the length

removing the excess.

**Please note: Mark the nal board

2mm under the measurement; This will

allow the timber to expand and

contract correctly.

Once all the oor boards are in position

secure each board into position using

8x40mm screws.

***Please Note: Ensure to screw through

each of the oor boards into the oor

bearers.

344x40mm Screws

40mm

screw

Pre drill

hole

*Cut to t

Roof

Closure Trim

Internal

*Measure and cut the

closure trims to

t the internal space.

Roof

Closure Trim

Internal

*Measure and cut the

closure trims to

t the internal space.

Pre drill

hole

30mm

screw

*trim to t

Step 15

Parts needed - No. 23 QTY 8

Inside the building place the closure

trim (No. 23) against the boarding

and align with the roof as shown in

the illustration.

Once in position x each trim

into place by pre drilling a pilot hole

and using 6x30mm screws per trim,

equally spacing them along the face

of the board.

48x30mm Screws

30mm

screw

Pre drill

hole

*Cut to t

Step 16

Parts needed - No. 23 QTY 8

Once the oor has been laid arrange the

closure trim (No. 23) around the outside

edge of oor (internally), measure and cut

down accordingly to best match the

internal space.

Secure each trim section into place using

6x30mm spaced equally along the board

as shown in the illustration.

*Do NOT x the closure trim to the oor

boards.

48x30mm Screws

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 02DTTWRS0605-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Wessex 03WES0808-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHDB0808DDOP-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 04GREEN0806SD-V6 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Wessex 03WES1208-V3 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTOSBA1008DDFW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04DTSTRDPN0804HGS-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OSBP1006SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03WES0808-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0305SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0510PB-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHAX0705HGD2MW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0619RANE3503FGSD3TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0608SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634CSNE0303HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02HIDE0705-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA0806SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1008DDOP-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01MODP0804-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01GRODB1008-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619VR3301-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products SELF BUILD PACK Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02DTTWR0605-V1-PEFC Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung