Mercia Garden Products 03DTSHAX0608FGD4MW-V1 Gebrauchsanweisung

ANTI-ROT

GUARANTEE TODAY

PLEASE SCAN HERE:

**Protim Aquatan T5 (621)**

Your building has been dip treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building has been treated by the

correct application of Aquatan solution and then allowed to dry.

Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

Measure

under the

head

Measure

overall

length

Screws & Nails Bolts To identify the

xings required

for each step use a

measuring tape.

03DTSHAX0608FGD4MW-V1

DIP TREATED SHIPLAP APEX 6X8 FULLY GLAZED DOUBLE DOOR 4 MEDIUM WINDOW

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

For ease of assembly, you

will need a tape measure to

check dimensions of

components.

P 1

Please retain product label and instructions for future reference

General Instructions

P 2

03DTSHAX0608FGD4MW-V1

Please retain product label and instructions for future reference

Overall Dimensions:

Width = 2494mm

Depth = 2457mm

Height = 2344mm

Base Dimensions:

Width = 2350mm

Depth = 1753mm

Pack Required:

03DTSHAX0608FGD4MW-V1 QTY 1

6x8 Summer House

Pack Required:

03DTSHAX0608FGD4MW-V1 QTY 1

03DTSHAX0208NWPB-V1 QTY 1

Overall Dimensions:

Width = 2494mm

Depth = 3057mm

Height = 2344mm

Base Dimensions:

Width = 2350mm

Depth = 2353mm

8x8 Summer House

Overall Dimensions:

Width = 2494mm

Depth = 3657mm

Height = 2344mm

Base Dimensions:

Width = 2350mm

Depth = 2953mm

Pack Required:

03DTSHAX0608FGD4MW-V1 QTY 1

03DTSHAX0208NWPB-V1 QTY 2

10x8 Summer House

Overall Dimensions:

Width = 2494mm

Depth = 2457mm

Height = 2344mm

Base Dimensions:

Width = 2350mm

Depth = 2390mm

Pack Required:

03DTSHAX0608FGD4MW-V1 QTY 1

03DTSHAX0208WCVPB-V1 QTY 1

6x8 Summer House

with Veranda

Pack Required:

03DTSHAX0608FGD4MW-V1 QTY 1

03DTSHAX0208NWPB-V1 QTY 1

03DTSHAX0208WCVPB-V1 QTY 1

Overall Dimensions:

Width = 2494mm

Depth = 3057mm

Height = 2344mm

Base Dimensions:

Width = 2350mm

Depth = 2990mm

8x8 Summer House

with Veranda

Overall Dimensions:

Width = 2494mm

Depth = 3657mm

Height = 2344mm

Base Dimensions:

Width = 2350mm

Depth = 3590mm

Pack Required:

03DTSHAX0608FGD4MW-V1 QTY 1

03DTSHAX0208NWPB-V1 QTY 2

03DTSHAX0208WCVPB-V1 QTY 1

10x8 Summer House

with Veranda

Press Lock QTY 1

PI-07-0018

Ring Pull QT Y2

PI-07-0032

Hinge QTY 6

PI-07-0004

Turn Button

QTY 2

PI-07-0182

21 22

Window Blocks QTY 16

PI-07-0011

Shed Finial QTY 2

SHED DIAMOND FINIAL

Felt

PI-01-0003

Tower Bolt QTY 2

PI-07-0068

8910

Secondary Door QTY 1

AI-STDFGSD475X1715-V1

Master Door QTY 1

AI-STDFGMD475X1715-V1

Door Gable Top QTY 1

AI-S11SHADDGT2300X566-V1

Plain Gable Top QTY 1

AI-S11SHAGT2300X566-V1

12 Door Framing 28x28x940mm QTY 1

FS2828-940mm

13 Gable Cover Trims 12x30x610mm QTY 4

S1230-610mm

14 Cover Trims 12x40x1712mm QTY 7

S1240-1712mm

15 Door Frame Strip 12x40x996mm QTY 1

S1240-996mm

16 Door Frame Strip 12x40x1740mm QTY 2

S1240-1740mm

17 Door Cover Trim 12x43x940mm QTY 1

S1243-940mm

Fascia 12x95x1365mm QTY 4

S1295-1365mm

Ridge Bar 27x70x1703mm QTY 1

F2770-1703mm

Corner Brace

QTY 2

PI-07-0012

P 3

Please retain product label and instructions for future reference

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

Window QTY 4

AI-FW540X1132-V1

Side Window Panel QTY 2

AI-03S11SH1SFWC879X1717-V1

Side Panel QTY 2

AI-S11SHPP879X1717-V1

Back Panel QTY 2

AI-S11SHPPTF1150X1669-V1

Front Window Panel QTY 2

AI-03S11SH1SFWC680X1669-V1

Floor QTY 2

AI-R11MBF1175X1753-V1

Roof QTY 2

AI-S11MBAR2409X1345-V1

Building Content - Pack A

03DTSHAX0608FGD4MW-V1

50mm Screw x 71

40mm Screw x 19

Felt Tacks x 150

30mm Black Screw x 48

60mm Screw x 10

20mm Black Screw x 22

Nail Bag

There may be extra screws present in the nail bag

30mm Screw x 110

P 4

Please retain product label and instructions for future reference

Building Content - Pack B

03DTSHAX0208NWPB-V1

Building Content - Pack C

03DTSHAX0208WCVPB-V1

50mm Screw x 10

40mm Screw x 4

30mm Screw x 56

60mm Screw x 4

Nail Bag

There may be extra screws present in the nail bag

14 Cover Trims 12x40x1712mm QTY 2

S1240-1712mm

Floor Extension QTY 1

AI-R11MBF2350X600-V1

Roof Extension QTY 2

AI-S11MBAR600X1345-V1

Plain Panel Extension QTY 2

AI-S11SHPP600X1717-V1

Floor Blocks QTY 8

F2828-400mm

U Channel QTY 3

PI-07-0031

Ridge Bar 27x70x599mm QTY 1

F2770-599mm

If 2ft Extension Pack has been purchased,

Please follow Steps labelled 2ft EXTENSION

PACK where present

Felt Tacks x 25

50mm Screw x 10

40mm Screw x 8

Nail Bag

There may be extra screws present in the nail bag

20mm Screw x 24

10mm Screw x 8

Veranda Floor QTY 1

AI-R11STVF2380X622-V1

Roof Support - 27x44x1719mm QTY 2

F2744-G-1739mm

Window Cross A - 16x27x500mm QTY 8

WC1627-500mm

Window Cross B - 16x27x1094mm QTY 4

WC1627-1094mm

35 36

Rail QTY 2

AI-03FR600X595-V1

P 5

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

8x8 Summer House 10x8 Summer House

Pre Assembly

Before assembling remove the transportation

blocks from the bottom of each panel.

Take care removing the blocks as to not damage

the panels. Tap with a at headed screwdriver

and hammer.

Dispose of the blocks once removed

Pre drill

hole

IMPORTANT: Pre-drill before xing screws.

Step 1

Parts needed - No. 6 QTY 2

Place the oor panels (No.6) onto a rm

and level base. Ensure the base has suitable

drainage, free from areas where standing

water can collect.

Secure the oors together using 10x50mm

screws through the oor bearers in an

alternating pattern.

10x50mm Screws

50mm

screw

2ft EXTENSION PACK

Step 1a

Parts needed - No. 6 QTY 2

- No. 29 QTY 1

- No. 32 QTY 8

Place the oor panels (No.6) onto a rm

and level base. Ensure the base has

suitable drainage, free from areas where

standing water can collect.

Secure the oors together using 10x50mm

screws through the oor bearers in an

alternating pattern.

Fix the Floor Extension (No.27) to the

assembled oors, Secure using Floor blocks

with 4x30mm screws per Floor block

Ensure the oor blocks are equally

spaced between the framing and

equally spread across both oors

32x30mm Screws

10x50mm Screws Pre drill

hole

30mm

screw

50mm

screw

32 32 32 32 32 32 32 32

32x30mm Screws

10x50mm Screws

64x30mm Screws

10x50mm Screws

P 6

Please retain product label and instructions for future reference

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 2

Parts Needed- No.2 QTY 1

- No.3 QTY 1

Place the Side panel (No.2) and the Back

Panel (No.3) onto the oor. Fix at the corner

using 3x50mm screws.

Do not secure the building to the oor

until the roof has been tted.

Position the panels so there is equal spacing

between the oor and cladding on all sides.

The side panels should sit higher than

then Back panels

3x50mm Screws

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 3

Parts Needed- No.2 QTY 1

- No.3 QTY 1

Place the Side panel (No.2) and the Back

Panel (No.3) along side the standing panels.

Fix in an alternating pattern using 3x50mm

screws per panel.

Do not secure the building to the oor

until the roof has been tted.

Position the panels so there is equal

spacing between the oor and cladding on

all sides.

6x50mm Screws

2ft EXTENSION PACK

Step 2a

Parts Needed- No.2 QTY 1

- No.3 QTY 1

- No.31 QTY 1

Place the Plain panel Extension (No.31) and

the Back Panel (No.3) onto the oor. Fix at the

corner using 3x50mm screws.

Place the Side panel (No.2) onto the oor and

x along the side in alternating pattern using

3x50mm screws.

Do not secure the building to the oor

until the roof has been tted.

Position the panels so there is equal

spacing between the oor and cladding on

all sides.

The side panels should sit higher than the

Back panels

6x50mm Screws Pre drill

hole

50mm

screw

Pre drill

hole

50mm

screw

2ft EXTENSION PACK

Step 3a

Parts Needed- No.2 QTY 1

- No.3 QTY 1

- No.31 QTY 1

Place the Back Panel (No.3) and the Side panel

(No.2) onto the oor. Fix in an alternating

pattern using 3x50mm screws per panel

Place the Plain panel Extension (No.31) onto

the oor. Fix at the corner using 3x50mm

screws

Do not secure the building to the oor

until the roof has been tted.

Position the panels so there is equal spacing

between the oor and cladding on all sides.

The side panels should sit higher than the Back

panels

9x50mm Screws

10x8 Summer

House

8x8 Summer

House

8x8 Summer

House

231

10x8 Summer

House

231

Please note: The side panels are all

interchangeable and can be positioned in

a variety of congurations. Decide which

works best before assembly

Please note: The side panels are all

interchangeable and can be positioned in

a variety of congurations. Decide which

works best before assembly

IMPORTANT: Pre-drill before xing screws.

P 7

Please retain product label and instructions for future reference

8x8

Summer House

10x8

Summer House

2ft EXTENSION PACK

Pre drill

hole

50mm

screw

Step 4

Parts Needed- No.1 QTY 2

Place the Side Window panels (No.1) onto

the oor. Fix in an alternating pattern using

3x50mm screws per panel.

Do not secure the building to the oor

until the roof has been tted.

Position the panels so there is equal

spacing between the oor and cladding on

all sides.

6x50mm Screws

Pre drill

hole

50mm

screw

2ft EXTENSION PACK

10x8 SUMMER HOUSE ONLY

Step 4a

Parts Needed- No.31 QTY 2

Place the Plain panels Extensions (No.31) onto

the oor. Fix in an alternating pattern using

3x50mm screws per panel.

Do not secure the building to the oor until

the roof has been tted.

Position the panels so there is equal spacing

between the oor and cladding on all sides.

6x50mm Screws

Please note: The side panels are all

interchangeable and can be positioned in

a variety of congurations. Decide which

works best before assembly

Please note: The side panels are all

interchangeable and can be positioned in

a variety of congurations. Decide which

works best before assembly

Please retain product label and instructions for future reference

P 8

IMPORTANT: Pre-drill before xing screws.

8x8 Summer House

10x8 Summer House

2ft EXTENSION PACK

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 5

Parts Needed- No.7 QTY 2

Place the Front Window panel (No.7) onto the

oor, x the corners using 3x50mm screws

Do not secure the building to the oor

until the roof has been tted.

Position the panels so there is equal

spacing between the oor and cladding on

all sides.

The Front panels should sit lower than the Side

panels

6x50mm Screws

Pre drill

hole

40mm

screw 12

Step 6

Parts Needed- No.12 QTY 1

Place the Door Framing (No.12) onto the

oor, between the Front Window Panels.

Ensure the framing is ush to the Window

Panel framing.

Ensure that the panels are all equally

spaced to the oor before xing the door

framing.

Secure the Door framing to the oor using

3x40mm screws

3x40mm Screws

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 7

Parts Needed- No.10 QTY 1

- No.11 QTY 1

Place the Plain Gable Top (No.10) on top of

the Back panels. Fix using 6x50mm screws

in an alternating pattern, going through

the gable framing and into the panel

framing below.

Place the Door gable top (No.11) on top of

the Front Window Panel. Fix using 4x50mm

screws

Ensure Cladding is tted correctly and

ush to the panels before securing.

10x50mm Screws

P 7

P 9

Please retain product label and instructions for future reference

8x8

Summer

House

10x8

Summer

House

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

30mm

screw

Step 8

Parts Needed- No.19 QTY 1

- No.24 QTY 2

Fix the Corner Braces (No.24) to each end

of the Ridge Bar (No.19) using 2x30mm

screws per corner brace.

Fix the Ridge bar to the top of each Gable

using 2x30mm screws per corner brace.

Ensure it is ush to the gable framing as

shown.

8x30mm Screws

Pre drill

hole

30mm

screw

2ft EXTENSION PACK

Step 8a

8x8 Summer House Parts Needed

- No.33 QTY 1

- No.34 QTY 1

10x8 Summer House Parts Needed

- No.33 QTY 2

- No.34 QTY 2

Fix the Ridge bar Extension (No.33) to the

Ridge Bar (No.19) using U Channels

(No.34), secure the U Channels using

6x30mm screws per U channel

Fix the Corner Braces to each end of the

assembled Ridge Bar using 2x30mm screws

per corner brace.

Fix the Ridge bar to the top of each Gable

using 2x30mm screws per corner brace.

Ensure it is ush to the gable framing as

shown.

14x30mm Screws (8x8 Summer House)

20x30mm Screws (10x8 Summer House)

40mm

screw

Pre drill

hole

Step 9

Parts needed - No. 5 QTY 2

For 2ft Extension Pack, go to Step 9a

on the next page

Place the Roof Panels (No. 5) on top of the

building making sure the framing in the roof

panels sits rmly within the Gable Tops (No.10

and No.11) and on top of the Ridge Bar

(No.19).

**Make sure that you have got the roof

panels the correct way round with the recess

at the top of the apex as shown in the

diagram.**

**The edges of the roof panels must be ush

with the outer cladding of the Plain Gable

Top (No.10).**

From the top, x directly through the roof

panels (No.5) and into the ridge bar (No.19)

the below using 5x60mm screws per roof

panel.

It is essential that the ridge bar (No.19) and

roof panel (No.5) framing pull together when

xed with 60mm screws. You may require

another person pushing the ridge bar (No.19)

up from below to achieve this.

HINT - Follow the nailing line of the framing on

the roof panel so that you are more likely to x

into the ridge bar below.

Fix the remaining sides of the roof panels using

40mm screws, ensuring to go through to the

framing below.

16x40mm Screws

10x60mm Screws

60mm

screw

P 8

P10

8x8 Summer

House

10x8 Summer

House

2ft EXTENSION PACK

Step 9a

8x8 Summer House Parts Needed

- No.5 QTY 2

- No.30 QTY 2

10x8 Summer House Parts Needed

- No.5 QTY 2

- No.30 QTY 4

Place a Roof Panel (No.5) and Roof extension

panel (No.30) on to one side of the building

making sure the framing in the roof panel sit

rmly within the Gable Top (No.11) and on top of

the Ridge Bar (No.19).

From the top, x directly through the roof panels (No.5 and

No.30) and into the ridge bar (No.19) below using 5x60mm

screws per roof panel.

**Place Roof Extension panels (No.30) to the back of the

building and keep the Roof Panel (No.5) to the front of the

building**

**Make sure that you have got the roof panels the correct

way round with the recess at the top of the apex as shown

in the diagram.**

**The edges of the roof panels must be ush with the outer

cladding of the Plain Gable Top (No.10).**

Once one side of the roof has been xed to the ridge

bar, lay the next Roof Panel (No.5) on top fo the

builing, using the xed roofs as a guide and secure to

the ridge bar using 5x60mm screws

Following the lay out of the Roof extensions already

laid on the bulindg, x the remaining roof extensions

onto the builing and secure to the ridge bar using

2x60mm screws per Roof Extension

It is essential that the ridge bar (No.19) and roof panels framing

pull together when xed with 60mm screws. You may require

another person pushing the ridge bar (No.19) up from below

to achieve this.

HINT - Follow the nailing line of the framing on the roof panel

so that you are more likely to x into the ridge bar below.

Fix the remaining sides of the roof panels using 40mm

screws, ensuring to go through to the framing below.

(8x8 Summer House) (10x8 Summer House)

20x40mm Screws 24x40mm Screws

14x60mm Screws 18x60mm Screws

40mm

screw

Pre drill

hole

60mm

screw

34 34

530 5

2ft EXTENSION PACK

Step 9a Continued

8x8 Summer House Parts Needed

- No.34 QTY 2

10x8 Summer House Parts Needed

- No.34 QTY 4

Once the Roofs have been layed out, x the

U channel (No.34) to the Roof Panel (No.5)

and the Roof Panel Extension (No.30).

Ensure the U channel is equally spaced over

both roofs framing, secure the U channel

using 6x30mm screws per channel

Repeat for both roof panels

8x8 Summer House-

12x30mm Screws

10x8 Summer House-

24x30mm Screws

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 03VER0808-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0806SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619PNSH1227FBSD-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03PTODB0406-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHCR0808FGD2TW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0806SDSEC-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0619RANE0325FGSD3TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0608SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619PNNE0403HGDD3SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03OVLPBRN0705-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04VCGRO-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA10DDGP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA1008DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01COMGRN0406-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628LOG127-V5 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHRA1008FGC42TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 2DTSHDB0606SFD5W-V1-PEFC Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 010VLPA0305SDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0644LOG186-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02RSE0505-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG173SG-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0619VR3301-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPA1208DDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628CSNE0404HGDD2SW-V1 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung