Mercia Garden Products 0628CSNE0303HGDD2SW-V1 Gebrauchsanweisung

P 1

2mm Drill bit

Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied)

including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm

bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions.

For the duration of heavy or extended periods of rain, swelling of the wood panels may

occur. Warping of the wood may also occur during excessive dry spells due to an interior

moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is

suggested that the outdoor building is sprayed with water during extended periods of

warm sunshine and sheltered as much as possible during rain or snow.

BUILDING A BASE

When thinking about where the building and base are going to be constructed:

Ensure that there will be access (60cm) to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to

diagrams for the base dimensions. The base should be slightly smaller than the external

measurement of the building, i.e. The cladding should overlap the base, creating a run

o for water. It is also recommended that the oor be at least 25mm above the

surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in

the case of childrens products independently tested to EN71 level, we cannot accept

responsibility for your safety whilst erecting or using this product.

Refer to the instructions pages for your specic product code

For ease of assembly use a

rubber mallet to t the log

boards. Do NOT use a heavy

hammer.

Ensure to measure and check before cutting

boards.

0628CSNE0303HGDD2SW-V1

28MM LOG CABIN, CORNER STANDARD, NO EXTRAS, 3X3M, HALF GLAZED DOUBLE

DOORS, TWO SHORT WINDOWS.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

It is advisable to use a hand

saw when cutting roof and

oor boards.

To ensure log boards are even, use a spirit

level to check each layer has been installed

correctly.

Measure

under the

head

Measure

overall

length

Screws & Nails Bolts

To identify the xings

required for each step use a

measuring tape.

P 2

0628CSNE0303HGDD2SW-V1

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Overall Dimensions:

Width = 4431mm

Depth = 3309mm

Height = 2912mm

Base Dimensions:

Width = 3971mm

Depth = 2988mm

Please retain product label and instructions for future reference

Roof Assembly 1

Roof Assembly 2

Window Contents

Double Door Contents

Rain Guard QTY 2

RG2844-710 (28x44x710mm)

Mortice Lock

QTY 1

PI-07-0017

Key Plate

QTY 1

PI-07-0017

Handles (Pair)

QTY 1

PI-07-0188

Adjustable Hinge QTY 6 PI-07-0209

Tower Bolt

QTY 2

PI-07-0114

Master Door QTY 1

(Morticed for lock)

AI-06LOGDGMD750X1900-V3

17a 17c

18 19 20 21

Slave DoorQTY 1

AI-06LOGDGSD750X1900-V3

Door Frame Left Upright - 71x70x2065mm QTY 1

AI-0628LOGDUFL-V3

Door Frame Right Upright - 71x70x2065mm QTY 1

AI-0628LOGDUFR-V3

Door Frame Top - 84x125x1632mm QTY 1

AI-0628LOGDDTF-V3

Door Frame Bottom - 71x70x1508mm QTY 1

AI-0628LOGDDBF-V3

Door Strip - 16x60x1880mm QTY 1

S1660-1880mm

Window QTY 2

AI-06LOGDGW684X1244-V3

Window Frame Left Upright - 71x70x1412mm QTY 2

AI-0628LOGWUFL-V3

Window Frame Right Upright - 71x70x1412mm QTY 2

AI-0628LOGWUFR-V3

Window Frame Top - 84x125x805mm QTY 2

AI-0628LOGWTF-V3

Window Frame Bottom - 71x70x805mm QTY 2

AI-0628LOGWBF-V3

Casement Stay QTY 2

PI-07-0187

Rain Guard QTY 1

RG2844-1520 (28x44x1520mm)

17b

Flag Hinge QTY 4

PI-07-0211

P 3

Please retain product label and instructions for future reference

Starter Board - 28x66x2191mm QTY 1

LB28RT66-AGRL-2191 (1x45 deg cut top, 1x45 deg cut bottom)

Log Board - 28x120x311mm QTY 18

LB28-BGL-311 (1x45 deg cut left)

Log Board - 28x120x311mm QTY 17

LB28-BGR-311 (1x45 deg cut right)

Log Board - 28x60x311mm QTY 1

LB28-BH60GR-311 (1x45 deg cut right, 60mm height board)

Log Board - 28x70x311mm QTY 1

LB28-BH70GR-311 (1x45 deg cut right bottom notch, 70mm height board)

Log Board - 28x120x2191mm QTY 1

LB28-J-2191 (1x45 deg cut left, 1x45 deg cut right top notch)

Log Board - 28x120x2191mm QTY 1

LB28-JD-2191 (1x45 deg cut left, 1x45 deg cut right top notch, door notch)

Starter Board - 28x66x1625mm QTY 1

LB28RT66-AGL-1625 (1x45 deg cut left)

Log Board - 28x120x1625mm QTY 6

LB28-AGL-1625 (1x45 deg cut left)

Log Board - 28x120x1625mm QTY 1

LB28-J-1625 (1x45 deg cut left 50mm bottom notch)

Log Board - 28x120x1625mm QTY 1

LB28-JDL-1625 (1x45 deg cut left 50mm bottom notch, window notch)

Log Board - 28x120x1625mm QTY 1

LB28-JDR-1625 (1x45 deg cut right, window notch)

Log Board - 28x120x1625mm QTY 7

LB28-AGR-1625 (1x45 deg cut right)

Finisher Board - 28x64x1625mm QTY 1

LB28-AH64GR-1625 (64mm high board, 1x45 deg deep cut right)

Finisher Board - 28x64x3000mm QTY 1

LB28-AH64-3000 (64mm high board)

Starter Board - 28x66x3000mm QTY 1

LB28RT66-A-3000

Log Board - 28x120x3000mm QTY 40

LB28-A-3000

Finisher Board - 28x80x1945mm QTY 1

LB28RG80-J-1945 (2x61 deg cut, 1945mm nished)

Finisher Board - 28x80x677mm QTY 1

LB28RG80-CGR-677 (2x45 deg cut left, 677mm nished)

Finisher Board - 28x80x677mm QTY 1

LB28RG80-CGL-677 (2x45 deg cut right, 677mm nished)

Finisher Board - 28x80x638mm QTY 6

LB28RG80-C-638

Log Board - 28x120x439mm QTY 24

LB28-B-439

Log Board - 28x120x439mm QTY 12

LB28-BGL-439 (1x45 deg cut left)

Log Board - 28x120x439mm QTY 12

LB28-BGR-439 (1x45 deg cut right)

Roof Truss - 40x140x922mm QTY 1

AI-06LOGC3X3-LRT-V1

Roof Truss - 40x140x922mm QTY 1

AI-06LOGC3X3-RRT-V1

Roof Truss A- 40x140x1604mm QTY 5

AI-06LOGC3RTA-V1

Bearer - 44x44x2808mm QTY 1

F4444-2808-PT

Bearer - 44x44x2720mm QTY 6

F4444-2720-PT

Bearer - 44x44x2492mm QTY 1

F4444-G-2492-PT (1x45 deg cut, 2492mm nished)

Bearer - 44x44x2222mm QTY 1

F4444-G-2222-PT (1x45 deg cut, 2222mm nished)

Bearer - 44x44x1951mm QTY 1

F4444-G-1951-PT (1x45 deg cut, 1951mm nished)

Bearer - 44x44x2055mm QTY 1

F4444-G-2055-PT (2x45 deg cut, 2055mm nished)

Bearer - 44x44x1356mm QTY 1

F4444-G-1356-PT (1x45 deg cut, 1356mm nished)

Bearer - 44x44x1680mm QTY 1

F4444-G-1680-PT (1x45 deg cut, 1680mm nished)

Roof Truss B - 40x140x2225mm QTY 1

AI-06LOGC3RTB-V1

Roof Truss C- 40x140x1604mm QTY 1

AI-06LOGC3RTC-V1 (2X76 deg parallel cuts, 1x45 deg mid right)

Roof Purlin - 45x120x1523mm QTY 1

F45120-B-1523

Roof Truss D- 40x140x1604mm QTY 1

AI-06LOGC3RTD-V1 (2X76 deg parallel cuts, 1x45 deg mid left)

Bearer - 44x44x1399mm QTY 1

F4444-G-1399-PT (1x45 deg cut, 1399mm nished)

*If you are constructing a 5x3 cabin you will not need

this part - see 5x3 instructions for correct part*

P 4

Please retain product label and instructions for future reference

Storm Brace - 27x44x2000mm QTY 8

F2744-2000

67 Closure Trim - 16x28x2400mm (approx length) QTY 14

S1628-2400

Floor Board Pack

AI-0628CSNE0303HGDD2SW-FBP-V1

Roof Board Pack A QTY 1

AI-06LOGC3X3-RBP1-V2

Fascia - 16x120x3100mm QTY 1

SR16120-3100

Felt

Fascia - 16x120x2225mm QTY 1

S16120-2225

Roof Board Pack B QTY 2

AI-06LOGC3X3RBP2-V2

Roof Board Pack C QTY 2

AI-06LOGC3X3RBP3-V2

Fascia - 16x120x2000mm QTY 2

S16120-2000

Fascia - 16x120x1658mm QTY 2

S16120-G-1658 (2x14 deg cuts, length 1658)

Gable QTY 1

AI-0628LOGC3-G-V1

Roof Spacers QTY 5

PI-07-0208 (20x100x2mm)

*HINT: keep the roof board packs

seperate to prevent mixing them up.

*HINT: keep the roof board packs

seperate to prevent mixing them up.

*HINT: keep the roof board packs

seperate to prevent mixing them up.

P 5

Please retain product label and instructions for future reference

Felt Tacks x 850

90mm Screw x 10

Nail Bag

40mm Screw x 666

30mm Screw x 182

120mm Screw x 12

70mm Screw x 85

70mm Bolt Set x 16

There may be extra screws present in the nail bag

80mm Screw x 24

Pre-assembly

*Please note:

Each board interlocks at either end in a staggered pattern.

Before securing ensure that the boards are tted properly in their respective

tongues and grooves.

TO CONSTRUCT A 5M X 3M LOG CABIN

PLEASE REFER TO THE 5X3

INSTRUCTIONS.

P 6

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

Please retain product label and instructions for future reference

60 59

Pre drill

hole

70mm

screw

Step 1

The following steps show how to

construct a 3m x 3m corner cabin.

To construct a 5m x 3m cabin, please

refer to the 5m x 3m instructions.

Parts needed - No. 53 QTY 1

No. 54 QTY 1

No. 59 QTY 1

No. 60 QTY 1

No. 61 QTY 1

Lay the bearers (No. 53, 54, 59, 60 &

61) onto a rm and level surface

(free from areas where standing

water can collect) as shown in the

illustration.

Fix the bearers together at each

corner using 10x70mm screws,

ensuring the frame is ush.

Once fully assembled, ensure the

bearers are square by measuring from

corner to corner, as illustrate, making

sure they are an equal measurement.

If the bearers are not alligned equally,

unscrew and adjust and re-align

accordingly.

10x70mm Screws

IMPORTANT: Pre-drill before xing screws.

Example picture

2 screws per bearer per end.

Pre drill

hole

70mm

screw

Step 2

Parts needed - No. 54 QTY 5

No. 55 QTY 1

No. 56 QTY 1

No. 57 QTY 1

No. 58 QTY 1

Arrange the remaining framing

(No. 54, 55, 56, 57, 58) as shown in

the illustration.

*Ensure there is an equal amount

of space between each frame.

Secure each of the frames in place

using 2x70mm screws for each end

of each bearer, ensuring the bearers

remains level.

36x70mm Screws

IMPORTANT: Pre-drill before xing screws.

P 7

Please retain product label and instructions for future reference

Pre drill

hole

Step 3

Parts Needed - No. 22 QTY 1

No. 32 QTY 1

No. 36 QTY 1

No. 40 QTY 1

No. 41 QTY 1

Place the starter boards (No. 22, 32, & 40) on to the assembled base

frame and place the rst two log boards (No.36 & 41) sitting in the notch as

shown.

Ensure the boards sit square on the base using the same method used in Step

1. Measure from corner to corner and ensure they are equal in

measurement.

Once the boards are square, x the starter boards (No. 22, 32, & 40) in

place, lift up the log boards (No.36 & 41) and x each starter board in place.

Fix each of the starter boards to the frame by screwing through the notch into

the frame with 1x70mm screw as shown in the illustration.

5x70mm Screws

70mm

screw

IMPORTANT: Pre-drill before xing screws.

1st

2nd

3rd 5th

4th

Step 4

Parts needed - No. 25 QTY 1

Make the log cabin level by

adding another board (No. 25)

as shown in the diagram. Fix

using 1x70mm screw.

**Ensure to stagger the screws

so as not to collide with the

previous screw.

1x70mm Screws

Pre drill

hole

70mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 5

Parts needed - No. 23 QTY 6

No. 24 QTY 6

No. 33 QTY 6

No. 36 QTY 5

No. 41 QTY 11

Lay the rst 6 boards (No. 23,

24, 33, 36 & 41) onto the starter

boards to create your rst level,

following the method as shown

in the illustrated.

Please note the right hand side

of the door will be slightly

higher. This will even out when

the rest has been assembled.

*Ensure that the boards are

level and ush with each other

as you lay each one.

Rubber Mallet

may be required

to t parts.

Please retain product label and instructions for future reference

Step 6

Parts Needed - No. 11 QTY 1

No. 12 QTY 1

No. 13 QTY 1

No. 14 QTY 1

Arrange the left, right, top & bottom door

frames (No’s. 11, 12, 13 & 14) onto a level

surface. Secure the top and bottom frames to

the uprights using 2x80mm screw per corner,

ensuring the screws do NOT protrude through

the front of the door framing.

8x80mm Screws

Pre drill

hole

80mm

screw

IMPORTANT : Pre-drill before xing screws.

The internal lip of the door

frame should be postioned on

the inside of the building.

14 12

Step 7

Parts Needed - No. 9 QTY 1

No. 10 QTY 1

No. 17 QTY 6

The Adjustable Door Hinge (No.17)

comes in three parts.

Fasten No. 17a into 17b as shown in the

illustration.

Place the master and slave doors

(No’s 9 & 10) onto a at surface and x the

Adjustable door hinge (No.17c) to the doors

using 3x30mm screws per hinge.

Fix 3 x Adjustable Door Hinges (No. 17a &

b) into position onto the door frame using

4x30mm screws per hinge.

*Ensure the hinges are tted to the exter-

nal of the door frame so the doors open

outwards from the log cabin.

Locate the doors into the hinges ensuring

there is equal spacing on each side between

the doors and door frame, and that the

doors open & close freely without restric-

tion.

It is important to t the doors within the

frames at this stage so that you can establish

the position of the hinges. The hinges come

in three parts. Remove the doors from the

frame after tting.

**Ensure to screw into the framing and not

into the channel.

42x30mm Screws

17a

Pre drill

hole

30mm

screw

17b

IMPORTANT : Pre-drill before xing screws.

Slave Door Master Door

P 9

Please retain product label and instructions for future reference

17a

Step 8

To adjust and align your doors:

1. Lift up the doors to separate the two parts

of the hinge.

2. Turn the rotating barrel (No.17a) in / out

to move the postion of the doors either in or

away from each other.

3. You can then place the door(s) back on to

the hinge and check the whether they

require more / less adjustments, if further

adjustments are required repeat number 2.

Step 9

Once you have laid 6 log boards (o of the starter)

up the door section, slide the assembled door

frame over the boards resting the frame on top of

the starter board (if you have not yet assembled

the door frame refer to step 6)

*Please note: This image is for illustrative purposes

and may dier from your choice in product

(regarding door position). Nevertheless the

process of tting the door frame is the same.

Step 10

Parts needed - No. 23 QTY 6

No. 24 QTY 6

No. 29 QTY 12

No. 30 QTY 6

No. 31 QTY 6

No. 41 QTY 11

Lay the next 6 boards (No. 23,

24, 29, 30, 31 & 41 ) onto the log

cabin to create your second

level, following the method as

shown in the illustration.

*Ensure that the boards are

level and ush with each other

as you lay each one.

Rubber Mallet

may be required

to t parts.

P 10

Please retain product label and instructions for future reference

IMPORTANT : Pre-drill before xing screws.

Step 11

Parts Needed - No. 2 QTY 2

No. 3 QTY 2

No. 4 QTY 2

No. 5 QTY 2

Arrange the left, right, top & bottom window

frames (No’s. 2, 3, 4,& 5) onto a rm and level

surface. Secure the top and bottom frames to

the uprights using 1x80mm screw per corner,

ensuring the screws do NOT protrude through

the front of the window framing.

Use this method to construct 2 windows.

16x80mm Screws

Pre drill

hole

80mm

screw

The internal lip of the window

frame should be postioned on

the inside of the building.

Pre drill

hole

30mm

screw

Step 12

Parts Needed - No. 1 QTY 2

No. 7 QTY 4

Position the window (No. 1) so that it

sits centrally within the window

frame. Fix the female part of the ag

hinge (No. 7) to the window using

4x30mm screws, attach the male part

of the ag hinge (No. 7) to the

window frame using 4x30mm screws

ensuring that the window can open

and close freely.

*Ensure to attach the hinge to the

horizontal frame of the window*

Repeat this method for both windows

**It is important to t the windows

within the frame at this stage so

that you can establish the position

of the hinges. The hinges come in

two parts. Remove the window

from the frame after tting.

32x30mm Screws

IMPORTANT : Pre-drill before xing screws.

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 02HIDE0705-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634AXNE0503HGDD2MW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 10DTSHAX0806-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03HEL1008DDFW-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 05DTMBAX0103SD-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02DTSHOA0705LFD3WBF-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04DTSTRDAX0406HGS-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX1006SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634RANE0504FGDD2TW1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01SHPWOR1210DDOW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04GREEN0606SD-V5 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0305SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG125SG-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DDPENT1408-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0705SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0644CVNE0403HGDD3SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0628RASH0302FBSDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPA0806DDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products CARLTON ARBOUR ESDXL21PT050 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01GRO1008DD-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVAX0806DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0628RANE0504FGDD2TW1SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHCR0909FGD4TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03TGCOR0707-V5 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung