Mercia Garden Products 03DTSHAX0705HGD2MW-V1 Bedienungsanleitung

ANTI-ROT

GUARANTEE TODAY

PLEASE SCAN HERE:

**Protim Aquatan T5 (621)**

Your building has been dip treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct

application of Aquatan solution and then allowed to dry.

Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

Measure

under the

head

Measure

overall

length

Screws & Nails Bolts To identify the

xings required

for each step use a

measuring tape.

03DTSHAX0705HGD2MW-V1

DIP TREATED SHIPLAP APEX 7X5 HALF GLAZED DOUBLE DOOR 2 MID WINDOW

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

For ease of assembly, you

will need a tape measure to

check dimensions of

components.

P 1

Please retain product label and instructions for future reference

General Instructions

P 2

03DTSHAX0705HGD2MW-V1

Please retain product label and instructions for future reference

Overall Dimensions:

Width = 2295mm

Depth = 1768mm

Height = 2279mm

Base Dimensions:

Width = 2066mm

Depth = 1456mm

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Overall Dimensions:

Width = 2295mm

Depth = 2233mm

Height = 2279mm

Base Dimensions:

Width = 2066mm

Depth = 1913mm

7X5- Pack A 7X7- Pack B

567

Plain Panel QTY 2

AI-S11SHPP1465X1710-V1

Secondary Door QTY 1

AI-STDHGSD574X1715-V1

Master Door QTY 1

AI-STDHGMD574X1715-V1

Roof QTY 2

AI-S11MBOHAR1720X1250-V1

234

Floor QTY 1

AI-R11MBF2066X1456-V1

Door Gable QTY 1

AI-03S11SHAGDD2018X2166-V1

Plain Gable QTY 1

AI-03S11SHAGP2018X2166-V1

8Ridge Bar 27x44x1409mm QTY 1

F2744-1409mm

13 Gable Cover trims 12x28x560mm QTY 2

S1228-560mm

Door Support Bar 12x40x1192mm QTY 1

S1240-1192mm

9Cover trims 12x40x1710mm QTY 4

S1240-1710mm

Fascias 12x60x1227mm QTY 4

S1260-1227mm

11 Door Cover trims 12x40x1740mm QTY 2

S1240-1740mm

Veranda Floor QTY 1

AI-R11STVF2066X457-V1

Roof QTY 2

AI-S11MBOHAR465X1250-V1

Railing QTY 2

AI-03FR430X702-V1

Roof Support 27x44x1722mm QTY 2

F2744-G-1742mm

Pack B-

Purchased Pack Component list

14 Gable Cover trims 12x28x533mm QTY 2

S1228-533mm

15 Window Strip 12x30x441mm QTY 2

S1230-441mm

16 Window Strip 12x30x855mm QTY 4

S1230-855mm

17 Shed Diamond QTY 2

Shed diamond nial

18 7.9m Felt QTY 1

PI-01-0016

19 Door Handles QTY 2

PI-07-0081

20 Butt Hinges QTY 6

PI-07-0066

21 Window Cill QTY 2

PI-08-0024

22 Corner Brace QTY 2

PI-07-0012

23 Press Lock QTY 1

PI-07-0162

24 Turn Button QTY 2

PI-07-0034

25 Styrene QTY 2

PI-05-0232

26 Barrel Bolt QTY 2

PI-07-0114

‘U’ Channel QTY 2

PI-07-0013

Pack A-

Purchased Pack Component list

60mm Screw x 12

50mm Screw x 34

Felt Tacks x 75

25mm Screw x 44

40mm Screw x 36

35mm Bolt x 4

10mm Screw x 8

50mm Screw x 12

40mm Screw x 6

30mm Screw x 12

Felt Tacks x 45

Pack A Pack B

Nail Bag

There may be extra screws present in the nail bag

30mm Screw x 48

P 3

Please retain product label and instructions for future reference

Pre Assembly

Before assembling remove the transportation

blocks from the bottom of each panel.

Take care removing the blocks as to not damage

the panels. Tap with a at headed screwdriver

and hammer.

Dispose of the blocks once removed.

Step 1

Parts needed - No 4 QTY 1

Place the oor (No.4) onto a rm

and level base. Ensure the base has

suitable drainage and is free from

areas where standing water can

collect.

Pre drill

hole

25mm

screw

Step 2

Parts needed - No 1 QTY 1

- No 21 QTY 2

- No 25 QTY 2

Lay the Door Gable onto a at surface with the

framing facing down.

Place the plastic window cill (No.21) onto the

external lip of the Door Gable (No.1). Fix the

Cill to the door gable framing using 2x25mm

screws per cill.

Lay the Styrene (No.25) into the window

openings so that it overlaps the surrounding

framing equally on both sides as per the

diagram

4x25mm Screws

25 25

Side View

Styrene

Window Cill

Cladding

Pre drill

hole

30mm

screw

IMPORTANT: Pre-drill before xing screws.

16 16

Step 3

Parts needed - No 15 QTY 2

- No 16 QTY 4

Attach the Window Strips (No.15 and

No.16) using 30mm screws as per the

diagram. Ensure the strip does not

protrude the width of the window

frame.

Ensure you screw into the window

strips though to the framing, avoiding

the Styrene where possible

18x30mm Screws

15 15

P 4

Pre drill

hole

25mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 4

Parts needed - No 6 QTY 1

- No 7 QTY 1

- No 20 QTY 6

Attach the doors (No. 6 and No.7) to

the door gable with 3x butt hinges

(No.20) per door, using 6x25mm

screws per hinge.

Ensure to screw the hinges into the

door gable framing.

*DO NOT SCREW INTO THE

WINDOW STRIPS*

36x25mm Screws 20

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 5

Parts needed - No 2 QTY 1

- No 5 QTY 1

Place the Plain Gable (No.2) and the

Plain panel (No.5) onto the oor.

Fix the corners with 50mm

screws as shown in the

illustration, making sure the

gable sits inside the plain

panel.

3x50mm Screws

6 7

Please retain product label and instructions for future reference

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 6

Parts needed - No 1 QTY 1

- No 5 QTY 1

Place the Door Gable (No.1) and the

Plain panel (No.5) onto the oor.

Fix the corners with 50mm

screws as shown in the

illustration, making sure the

gable sits inside the plain

panel.

3x50mm Screws

Pre drill

hole

30mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 7

Parts needed - No 8 QTY 1

- No 22 QTY 2

Place the Ridge Bar (No.8) inbetween

the gables, resting ush with the top

of the gable framing.

Secure to the gables using a corner

brace (No.22) at each end, using

4x30mm screws per brace.

8x30mm Screws

P 5

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

**If you have purchased a 7x7 Summer House with Pack B

extension then skip to step 8a**

Step 8

Parts needed - No 3 QTY 2

60mm

screw

Pre drill

hole

Place the Roof Panel (No. 3) on top of the

building making sure the framing in the

roof panels sits rmly within the Gables

(No. 1 & 2) and on top of the Ridge Bar

(No. 8).

**Make sure that you have got the roof

panels the correct way round with the

recess at the top of the apex as shown in

the diagram.**

From the top, x directly through the roof

panels (No. 3) into the ridge bar (No. 8)

below using 5x60mm screws per roof

panel.

It is essential that the ridge bar (No. 8) and

roof panels (No. 3) framing pull together

when xed with 60mm screws. You may

require another person pushing the ridge

bar (No. 8) up from below to achieve this.

HINT - Follow the nailing line of the framing

on the roof panel so that you are more

likely to x into the ridge bar below.

10x60mm Screws

IMPORTANT: Pre-drill before xing screws.

Please retain product label and instructions for future reference

P 6

Please retain product label and instructions for future reference

Use 40mm screws to x the roof (No. 3)

down the sides, front and back of the

building.

Be sure that the screws attach into the

framing below.

20x40mm Screws

Pre drill

hole

40mm

screw

Step 9 IMPORTANT: Pre-drill before xing screws.

Step 10 IMPORTANT: Pre-drill before xing screws.

bbbb

bbbbbbb

Pre drill

hole

50mm

screw

Secure the building to the

oor internally using

28x50mm screws.

*Ensure to screw through the

framing into the oor bearers.

28x50mm Screws

*Cut down

trims to t

Pre drill

hole

30mm

screw

Step 11

Parts needed - No 9 QTY 4

- No 13 QTY 2

- No 14 QTY 2

Attach the cover trims (No.9) to

each corner of the building using

3x30mm screws per cover trim.

Attach the gable cover trims

(No.13 and No.14) onto the door

gable.

Cut the gable cover trims (No.13)

and the cover trims (No.9) to t as

shown in the illustration

8x30mm Screws

IMPORTANT: Pre-drill before xing screws.

P 7

Please retain product label and instructions for future reference

Felt

tacks

Cut the felt (No.18) into 3 strips

and place onto the roof, as shown

in the illustration. ensuring there

is approximatly 50mm of

overhanging around the building

Fix the sheets into place using 75x

felt tacks approximately 100mm

apart.

75x Felt Tacks

Step 12

Parts needed - No 18 QTY 1

HANDLE

WITH CARE

18 Fix the fascias (No.10) to the

building using 3x40mm screws

per fascia, ensuring the screws go

through to the roof framing

Fix the Shed Diamonds (No.17)

onto the fascias using 2x40mm

screws per nial

16x40mm Screws

Pre drill

hole

40mm

screw

Step 13

Parts needed - No 10 QTY 4

- No 17 QTY 2

IMPORTANT: Pre-drill before xing screws.

Attach the door handles (No.19) to the

doors using 25mm bolts included with

the door handle.

Pre drill a hole approximately 3mm and

x the handle from the inside with the

provided bolts

Attach the two turn buttons (No.24)

above the master door at the top and

bottom using 2x30mm screws.

*These turn buttons help to keep your

doors straight during high & low levels

of moisture content in the air.

2x30mm Screws

4x35mm Bolt

Pre drill

hole

35mm

bolt

Step 14

Parts needed - No 19 QTY 2

- No 24 QTY 2

30mm

screws

IMPORTANT: Pre-drill before xing screws.

P 8

Please retain product label and instructions for future reference

IMPORTANT: Pre-drill before xing screws.

Step 15

Parts needed - No 11 QTY 2

- No 12 QTY 1

11 11

On the inside of the building x

the Door Frame Strips (No.11 &

12), to the top and sides of the

doors frames. Make sure that the

edges are ush with the edge of

the framing. Fix with 4x30mm

screws per strip.

12x30mm Screws

Pre drill

hole

30mm

screw

Pre drill

hole

25mm

screw

10mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 16

Parts needed - No 23 QTY 1

- No 26 QTY 2

Secure the barrel bolts (No.26) to the top

& bottom of the secondary door using

4x10mm screws.

Attach the press lock (No.23) to the

master door with 4x25mm screws, aligning

the barrel with the key hole.

*Ensure the key turns and locks properly

before xing to the door.

8x10mm Screws

4x25mm Screws

It is ESSENTIAL that you apply wood treat-

ment immediately after the building has

been assembled.

AFTER TREATMENT:

score around protective

cover on glazing and

carefuly peel

covering back

Please retain product label and instructions for future reference

P 9

Fix the roofs (No.3 and No.28)

framing together using the ‘U’

Channel (No.31), laying evenly

over the roof framing pieces,

secure using 6x30mm screws.

Repeat for both roof panels.

12x30mm Screws

Pre drill

hole

30mm

screw

Step 8a

Parts needed - No 3 QTY 2

- No 28 QTY 2

- No 31 QTY 2

IMPORTANT: Pre-drill before xing screws.

31`

Step 9a

Parts needed - No 3 QTY 2

- No 28 QTY 2

- No 31 Qty 2

60mm

screw

Pre drill

hole

Place the assembled Roof Panels (No. 3, 28

& 31) on top of the building making sure

the framing in the roof panels sits rmly

within the Gables (No. 1 & 2) and on top of

the Ridge Bar (No. 8).

**Make sure that you have got the roof

panels the correct way round with the

recess at the top of the apex as shown in

the diagram.**

From the top, x directly through the roof

panels (No. 3 & 28) into the ridge bar (No.

8) below using 5x60mm screws per assem-

bled roof panel.

It is essential that the ridge bar (No. 8) and

roof panels (No. 3 & 28) framing pull

together when xed with 60mm screws.

You may require another person pushing

the ridge bar (No. 8) up from below to

achieve this.

HINT - Follow the nailing line of the framing

on the roof panel so that you are more

likely to x into the ridge bar below.

10x60mm Screws

IMPORTANT: Pre-drill before xing screws.

Please retain product label and instructions for future reference

P 10

Use 40mm screws to x the roof (No. 3

& No. 28) down the sides, front and

back of the building.

Be sure that the screws attach into the

framing below.

20x40mm Screws

Pre drill

hole

40mm

screw

Step 10a IMPORTANT: Pre-drill before xing screws.

bbbb

bbbbbbb

Step 11a IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

50mm

screw

Secure the building to the

oor internally using

28x50mm screws.

*Ensure to screw through the

framing into the oor bearers.

28x50mm Screws

IMPORTANT: Pre-drill before xing screws.

*Cut down

trims to t

Pre drill

hole

30mm

screw

Step 12a

Parts needed - No 9 QTY 4

- No 13 QTY 2

- No 14 QTY 2

Attach the cover trims (No.9) to

each corner of the building using

3x30mm screws per cover trim.

Attach the gable cover trims

(No.13 and No.14) onto the door

gable.

Cut the gable cover trims (No.13)

and the cover trims (No.9) to t as

shown in the illustration

8x30mm Screws

IMPORTANT: Pre-drill before xing screws.

Step 13a

Parts needed - No 27 QTY 1

Place the Veranda Floor (No.27) on the

ground, ush to the door gable as

shown in the illustration.

Ensure the veranda oor sits

centrally to the building.

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01OVLPA0806DDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01SHPSTR0402-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0305SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHCR0808FGD2TW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0644LOG133-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03HEL1008DDFW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0634RANE0504HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX1006SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628RASH0302FBSDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHPN1006FGD2TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03TGCOR0707-V5 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628RANE0403HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTGRODB1008-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVAX08DDNWGP-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01BEACH-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG125SG-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02SNO0705-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03WES1008-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01TDM0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0406DDNW-V Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01JER0806-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1008DDOP-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0705SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1206DDOP-V1 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung