Mercia Garden Products 03DTSHPN1006FGD2TW-V1 Gebrauchsanweisung

ANTI-ROT

GUARANTEE TODAY

PLEASE SCAN HERE:

**Protim Aquatan T5 (621)**

Your building has been dip treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building has been treated by the

correct application of Aquatan solution and then allowed to dry.

Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

Measure

under the

head

Measure

overall

length

Screws & Nails Bolts To identify the

xings required

for each step use a

measuring tape.

03DTSHPN1006FGD2TW-V1

DIP TREATED SHIPLAP PENT 10FT X 6FT FULLY GLAZED DOUBLE 2 TALL WINDOW

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

For ease of assembly, you

will need a tape measure to

check dimensions of

components.

P 1

Please retain product label and instructions for future reference

General Instructions

1 2 3 4

567

Door Panel

AI-03S11SHDD1180X2075-V1

Twin Window Panel

AI-03S11SH2TFWC1738X2075-V1

Back Panel QTY 2

AI-S11SHPP1459X2015-V1

Floor QTY 2

AI-R11MBF1456X1753-V1

Roof QTY 3

AI-S21MBPR1001X2305-V1

Contents

Right Panel

AI-03S11SHPGR1707X2119-V1

Left Panel

AI-03S11SHPGL1707X2119-V1

P 2

03DTSHPN1006FGD2TW-V1

Overall Dimensions:

Width = 3028mm

Depth = 2343mm

Height = 2170mm

Base Dimensions:

Width = 2912mm

Depth = 1753mm

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

9 10 11

Butt Hinge QTY 6

PI-07-0066

Door Handle QTY 2

PI-07-0081

Turn Button QTY 2

PI-07-0034

Press Lock

PI-07-0162

Barrel Bolt QTY 2

PI-07-0114

Window Beading Block

QTY 16

PI-07-0011

Fitted Window QTY 2

AI-FW653X1582-V1

Felt

Cover Trim - 12 x 40 x 2070mm QTY 3

S1240-2070mm

Cover Trim - 12 x 40 x 2035mm QTY 3

S1240-2035mm

Fascia - 12 x 95 x 2306mm QTY 2

S1295-2306mm

Fascia - 12 x 95 x 1514mm QTY 4

S1295-1514mm

Under Roof Panel QTY 2

AI-S11MBURF1499X484-V1

Master Door

AI-STDFGMD475X1715-V1

Secondary Door

AI-STDFGSD475X1715-V1

Door Frame Strip - 12 x 40 x 1740mm QTY 2

S1240-1740MM

Door Frame Strip - 12 x 40 x 996mm QTY 1

S1240-996MM

Eaves Frame - 28 x 28 x 1001mm QTY 3

FS2828-1001mm

Rain Guard - 990mm QTY 1

RG2844-990mm

Rain Guard - 1354mm QTY 1

RG2844-1354mm

Finial QTY 1

SHED DIAMOND FINIAL

P 3

Please retain product label and instructions for future reference

Nail Bag

There may be extra screws present in the nail bag

40mm Screw QTY 18

Felt Tacks QTY 125

25mm Screw QTY 22

30mm Screw QTY 130

50mm Screw QTY 108

35mm Bolt QTY 4

10mm Screw QTY 12

Pre Assembly

Before assembling remove the transportation

blocks from the bottom of each panel.

Take care removing the blocks as to not damage

the panels. Tap with a at headed screwdriver

and hammer.

Dispose of the blocks once removed.

Step 1

Parts needed - No. 1 QTY 1

- No. 9 QTY 1

- No. 10 QTY 1

- No. 22 QTY 6

- No. 27 QTY 2

Fix the hinges to the master (No. 9) and

secondary (No. 10) doors and to the door

panel (No. 1) using 3x butt hinges (No. 22)

per door. Ensure to predrill holes.

* Fix to the door using 3x25mm screws &

3x30mm screws to the Door Panel per

hinge, ensure the doors open freely.

Fix the door handles (No. 27) to the outside

of the master and secondary door using

the 35mm bolts provided.

4x35mm Bolts

18x25mm Screws

18x30mm Screws

Pre drill

hole

25mm

screw

30mm

screw

35mm

bolt

Step 2

Parts needed - No. 21 QTY 1

- No. 26 QTY 2

Secure the barrel bolts (No. 26) to the

top & bottom of the secondary door using

6x10mm screws. Pre-drill the holes

beforehand. Drill a hole in the framing

above and below the door for the barrel

bolt to x into.

Attach the press lock (No. 21) to the

master door with 4x25mm screws, aligning

the barrel with the key hole.

*Ensure the key turns and locks properly

before xing to the door.

12x10mm Screws

4x25mm Screws

Pre drill

hole

10mm

screw

25mm

screw

P 4

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

Please retain product label and instructions for future reference

Pre drill

hole

50mm

screw

Place the assembled oor panels

(No. 6) upside down onto a rm and

level base. Ensure the base has

suitable drainage, free from areas

where standing water can collect.

Secure the oors together using

10x50mm screws through the oor

bearers in an alternating pattern.

Once xed together turn the oor

back the right way up.

10x50mm Screws

Step 3

Parts needed - No. 6 QTY 2

Fix the corners with 50mm

screws as shown in the

illustration.

Do not secure the building

to the oor until the roof

is tted.

4x50mm Screws

Pre drill

hole

50mm

screw

Step 4

Parts needed - No. 4 QTY 1

- No. 5 QTY 1

Join the Left Panel (No. 4) together with

Back Panel (No. 5) as shown in the illustration.

*Please note that the back panel is

is shorter than the side panels

Step 5

Parts needed - No. 3 QTY 1

- No. 5 QTY 1

Connect the Back Panel (No 5.) to the

already standing Back Panel. Followed by

adding the Right Panel (No.3).

*Please note that the back panel is

is shorter than the side panels

Fix the corners with 50mm

screws as shown in the

illustration.

Do not secure the building

to the oor until the roof

is tted.

8x50mm Screws

Pre drill

hole

50mm

screw

Step 6

Parts needed - No. 2 QTY 1

Connect the Twin Window Panel (No. 2)

with Right Panel (No. 3).

*Please note that the twin window panel

is shorter than the side panels

Fix the corners with 50mm

screws as shown in the

illustration.

Do not secure the building

to the oor until the roof

is tted.

4x50mm Screws

Pre drill

hole

50mm

screw

P 5

Please retain product label and instructions for future reference

Step 7

Parts needed - No. 1 QTY 1

Fix the Door Panel (No. 1) between the

Twin Window Panel (No. 2) and the Left

Panel (No. 4) using 50mm screws in

alternating directions.

*Please note that the Door panel is

shorter than the side panels.*

Fix the panels together with

50mm screws as shown in the

illustration.

Do not secure the building

to the oor until the roof

is tted.

8x50mm Screws

Pre drill

hole

50mm

screw

Step 8

Parts needed - No. 7 QTY 3

- No. 20 QTY 3

50mm

screw

Pre drill

hole

Fix the Eaves framing (No.20) to the

roof (No.7) using 4x50mm screws per

eaves framing, screwing through the

eaves framing and into the roof

framing.

Ensure the eaves framing is ush

to the edges of the roof framing

before securing

12x50mm Screws

Step 9

Parts needed - No. 7 QTY 3

Place the Roof Panels (No. 7) onto the top

of the building. Align the three Roof Panels

so they sit square before xing into postion.

The roof eaves frames (No. 20) should sit at

the back of the building.

*The roof panels should sit on top of the

left and right panels, the roof panels

framing should sit on top of the back,

door and twin window panels.*

Do not secure the building to the Floor

until the roof is tted.

777

Step 10

Fix the three Roof Panels (No. 7)

together using 50mm screws. Oset

the screws from each other as shown

in the diagram.

*Roof boards not shown for

illustration purposes.

Do not secure the building to

the Floor until the roof is

tted.

16x50mm Screws

Pre drill

hole

50mm

screw

777

P 6

Please retain product label and instructions for future reference

Step 12

Once the Roof is aligned and secure the

Floor can be xed into postion.

Fix the building into place by screwing

through the panel into the oor making

sure to screw into the oor bearers.

20x50mm Screws

Pre drill

hole

50mm

screw

Step 13

Parts needed - No. 8 QTY 2

One at a time place the Under Roof Panels

(No. 8) into position, making sure they are

ush to the front of the building. Using a

pencil mark on the under roof panel where

the roof panel framing is to use as a guide

for xing into place.

Fix in place making sure to screw through

in to the Roof framing. Pre-drill holes rst.

30x30mm Screws

Pre drill

hole

30mm

screw

Step 11

Screw internally with 10x50mm screws

securing the roof panels (No. 7) at

the front and back of the building.

*Roof boards not shown for

illustration purposes.

Do not secure the building to the

Floor until the roof is tted.

20x50mm Screws

Pre drill

hole

50mm

screw

P 7

Please retain product label and instructions for future reference

HANDLE

WITH CARE

Step 14

Parts needed - No. 24 QTY 1

Cut the Felt (No. 24) into 3 sheets at 3110mm

each and lay onto the roof. Starting at the

back and working towards the front.

*Ensure there is approximately 50mm of

overhang around the building.

Fix into place using 125x felt tacks at

100mm intervals.

125x Felt tacks Felt Length 3110mm

Felt

tacks

Step 15

Parts needed - No. 16 QTY 2

- No. 17 QTY 4

Fix the fascias (No. 16 & 17) to the

front, back and sides of the building

using 18x40mm screws.

Ensure the fascia xed to the back of

the roof nishes ush with the top to

enable water to run o.

18x40mm Screws

Pre drill

hole

40mm

screw

Please retain product label and instructions for future reference

P 8

Pre drill

hole

30mm

screw

Step 16

Parts needed - No. 11 QTY 4

- No. 23 QTY 16

Position the windows (No. 11) central into

the window opening.

Fix eight Window Blocks (No. 23) to the

Window, four down each side and x

with 1x30mm screw.

Place the Window into the window panel

and x by screwing though the Window

Block (No. 23) with 2x30mm screws as

shown.

Fix the window beading blocks (No. 23) to

the window before tting the window into

the panel.

48x30mm screws.

11 11

Step 17

Parts needed - No. 12 QTY 1

- No. 13 QTY 1

Fix a rain guard above the double

doors (No. 12) and one rain guard

above the two front windows (No. 13).

Secure in place using 3x50mm screws

per guard, ensuring to screw through

the framing at an angle.

6x50mm Screws

Pre drill

hole

50mm

screw

Step 18

Parts needed - No. 14 QTY 3

- No. 15 QTY 3

Attach the cover trims (No. 14 at

the front) and (No. 15 at the rear)

to each corner of the building and

over panel joins. Use 3x30mm

screws per cover trim.

18x30mm Screws

Pre drill

hole

30mm

screw

P 9

Please retain product label and instructions for future reference

Step 19

Parts needed - No. 25 QTY 2

- No. 28 QTY 1

Attach the two turn buttons (No. 25)

to the secondary door at the top and

bottom using 2x30mm screws.

Attach the Finial (No. 28) centrally

over the two front fascias using

2x30mm screws.

4x30mm Screws

*These turn buttons help to keep

your doors straight during high &

low levels of moisture content in

the air.

Pre drill

hole

25 28

30mm

screw

Step 20

Parts needed - No. 18 QTY 2

- No. 19 QTY 1

On the inside of the building x

the Door Frame Strips (No. 18

& 19), to the top and sides of

the doors frames. Make sure

that the edges are ush with

the edge of the framing. Fix

with 4x30mm screws per strip.

12x30mm Screws

Pre drill

hole

30mm

screw

18 18

Please retain product label and instructions for future reference

P 10

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

AFTER TREATMENT:

score around protective

cover on glazing and

carefully peel

covering back

SILICONE

SEALANT

Step 21

It is recommended that after the

construction, treatment and the

removal of the protective window

cover that sealant is used to

keep the building weather tight.

1. Treat the building

2. Remove lm from the windows

3. Add sealant around the windows.

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01OVLPA0808DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0634RANE0504HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG015-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVRA1006SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products Tulip Playhouse 02TUL411411-V4-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01SHPWOR2010DDOW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619WKNE2633LBDD1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03TGCORSE0408-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01GRODB1008-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619LOG015-V4 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHHP0806HGD4MW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0628RANE0403HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0806SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0644CSNE0303HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0644CSNE0404HGDD2SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHOSBRAX0806SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHCV0808HGD4MW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0634LOG249-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 010VLPA0305SDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03HEL1010DDFW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHPN0409DSHPB-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0628AXNE0503HGDD2MW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0628LOG181-V4 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03OVLPBRN0705-V3 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung