Mercia Garden Products 06LOG125SG-V1 Gebrauchsanweisung

P 1

06LOG125SG-V1 & 06LOG125DG-V1 (4x4m)

06LOG125SG-V1: 4x4m 28mm apex cabin with single (glass) glazing.

06LOG125DG-V1: 4x4m 28mm apex cabin with double (glass) glazing.

2mm Drill bit

Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All building’s should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 880514

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied)

including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm

bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions.

For the duration of heavy or extended periods of rain, swelling of the wood panels may

occur. Warping of the wood may also occur during excessive dry spells due to an interior

moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is

suggested that the outdoor building is sprayed with water during extended periods of

warm sunshine and sheltered as much as possible during rain or snow.

Our buildings are pre treated with a water based treatment**; this only helps to protect

the product during transit and for upto 3 months against mould. To validate your

guarantee and ensure longevity of the product, it is ESSENTIAL the building is treated

with a wood preserver within the rst three months of assembly and thereafter in

accordance with the manufactures recommendations. Care must be taken to ensure

the product is placed on a suitable base.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to

diagrams for the base dimensions, The base should be slightly smaller than the external

measurement of the building, i.e. The cladding should overlap the base, creating a run

o for water. It is also recommended that the oor be at least 25mm above the

surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in

the case of childrens products independently tested to EN71 level, we cannot accept

responsibility for your safety whilst erecting or using this product.

Refer to the instructions pages for you specic product code

For ease of assembly use a

rubber mallet to t the log

boards. Do NOT use a heavy

hammer.

Ensure to measure and check before cutting

boards.

It is advisable to use a

circular saw when cutting

roof and oor boards.

21 34

P 2

06LOG125SG-V1 & 06LOG125DG-V1

Overall Dimensions:

Width = 4110mm

Depth = 5232mm

Height = 2741mm

Base Dimensions:

Width = 3808mm

Depth = 3808mm

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Window

QTY 2

Slave Door Master Door Log 125 Gable - 4000mm

QTY 2

Starter Board (S1) - 66x28x4000mm QTY 2

LB28RT66-4000mm

Log Board (A) - 120x28x4000mm QTY 54

LB28-4000mm

Log Board (B) - 120x28x1215mm QTY 12

LB28-1215mm

Log Board (B) - 120x28x233mm QTY 24

LB28-233mm

Log Board (E) - 120x28x233mm QTY 24

LB28-233mm (No Notch)

Log Board (WA) - 120x28x4400mm QTY 2

LB28-4400mm

Log Board (WA) - 120x28x4800mm QTY 2

LB28-4400mm

Log Board (WA) - 120x28x5200mm QTY 2

LB28-5200mm

Roof Board - 121x16x2114mm QTY 94

MB16-2114mm

Floor Board - 121x16x3750mm QTY 34

MB16-3750mm

Bearer - 44x44x3720mm QTY 13

F4444-3720mm (Pressure Treated)

Bearer - 44x44x3808mm QTY 2

F4444-3808mm (Pressure Treated)

Purlin - 120x45x5200mm QTY 3

F45120-5200mm

Fascia - 120x16x2118mm QTY 4

S16120-2118mm (Angled)

Eaves Frame - 44x27x2600mm QTY 4

F2744-2600mm

Storm Brace - 27x44x2100mm QTY 8

F2744-2100mm

Skirting - 28x28x2400mm QTY 6

FS2828-2400mm

Interior Roof Trim - 27x44x2400mm QTY 5

F2744-2400mm (Bevelled)

20 Door Strip - 16x1660x1880mm

F1660-1880mm

Door Frame Top & Bottom - 69x55x1505mm QTY 2

WF5569-1505mm (28mm)

Felt Tacks x600

70mm Screw x200

30mm Black Screw x21

Step 3

Attatch the door strip (No. 20) to the

back of slave door using 4x40mm

screws as shown in the illustration.

Once xed secure the tower bolts

(No. 28) to the top and bottom of

the strip using the screws provided.

*These tower bolts help to keep

your doors straight during high

and low levels of moisture content

in the air.

4x40mm Screws

Pre drill

hole

40mm

screw

Mortice Lock Key Plate Handles (Pair)Felt

Tower Bolt

QTY 2

Pre-assembly

*Please note:

Each board interlocks at

either end in a staggered pattern.

Before securing ensure that the boards

are tted properly in their respective

tongue’s and groove’s.

Pre drill

hole

IMPORTANT: It is imperative that you pre-drill before xing screws.

Casement Stay QTY 2

Nail Bag

40mm Screw x600

30mm Screw x24

P 3

Please retain product label and instructions for future reference

Step 1: Door Frame Fit

Arrange the door framing onto a rm and

level surface. Secure the top and bottom

frames (No. 21) to the uprights (attached

to each door). Fix into place using 1x70mm

screw per corner, ensuring the screws

do NOT protrude into the channel

either side of the doors.

*Please note: This image is for

illustrative purposes and may

dier from your choice in product

(regarding hinges). Nevertheless

the process of xing the frames is

the same.

4x70mm Screws

Pre drill

hole

70mm

screw

The Mortice Lock is Reversible

Step 2

Fit the mortice lock (No. 25) into the recess

in the master door (No. 3) and secure

using the screws provided. Attach the key

plate (No. 26) to the slave door (No. 1)

with the screws provided.

Fit the door handles (No. 25) and connect

with the metalbar to the mortice lock

using 8x30mm screws. Ensure the lock

mechanism closes correctly. If not, remove

the lock and turn the catch around using

the small grub screw.

*Please note: This image is for illustrative purposes

and may dier from your choice in product

(regarding ironmongery). Nevertheless the process

of xing the frames is the same.

12x30mm Screws

25 26 27 28 29

*Ensure the top & bottom rails sit inbetween

the upright framing attached to the doors.

30mm

screw

80mm Bolt Set x24

Pre drill

hole

70mm

screw

Pre drill

hole

70mm

screw

Pre drill

hole

IMPORTANT: It is imperative that

you pre-drill before xing screws.

Pre drill

hole

30mm

screw

P 4

For assistance please contact customer care on: 01636 880514

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

Please retain product label and instructions for future reference

Step 5

Lay the starters (No’s. 15 & 16)

onto a rm and level surface

(free from areas where standing

water can collect) as shown in the

illustration.

Fix the framing together at each

corner using 8x70mm screws,

ensuring the frame is ush.

8x70mm Screws

Step 6

Following the same method

outlined in Step 5, arrange the

remaining framing (No. 15) as

shown in the illustration.

*Ensure there is an equal

amount of space between each

frame.

Secure each of the frames in place

using 4x70mm screws per frame,

ensuring the framing remains level.

44x70mm Screws

70mm

screw

Step 7 (See Pre-Assembly)

Place the starter boards (No’s. 5

& 6) on to assembled base frame

along the longest sides.

*Ensure the notches at either

end of each board are ush

and level with the ends of the

frame.

Fix each of the starter boards to

the frame by screwing through

the notch into the frame as shown

in the illustration.

4x70mm Screws

Step 4

Fix the casement stay (No. 30) onto

the window (No. 1) and the casement

stay pins to the window cill using

6x30mm (black) screws per casement

stay.

*Ensure the casement stay is centralised

on the window.

12x30mm Screws

15 15 15 15 15 15 15 15 15 15 15

IMPORTANT: It is imperative that you pre-drill before xing screws.

P 5

Please retain product label and instructions for future reference

Step 8 (See Pre-Assembly)

Following the same method

outlined in Pre-Assembly, lay

the rst 6 boards (No’s. 6 & 7)

onto the starter boards to

create your rst level.

*Ensure that the boards are

level and ush with each

other as you lay each one.

Fix every third board to the

one below by screwing

through the notch as shown

in the illustration using

1x70mm screw per side.

**Ensure to stagger the screws

so as not to collide with the

previous screw.

16x70mm Screws

Pre drill

hole

70mm

screw

Step 9

Once you have laid 6 log boards (o of the

starter) up the door section, slide the

assembled door frame assembly over the

boards resting the frame on top of the

starter board.

*Please note: This image is for illustrative

purposes and may dier from your choice in

product (regarding door position).

Nevertheless the process of tting the door

frame is the same.

**Please Note: The short boards at the

front of the building (either side of

the door and window opening’s)

can be placed either side depending

on your needs.

Step 10 (See Pre-Assembly)

Following the same method

outlined in Pre-Assembly, lay

the next 6 boards (No’s. 6, 8

& 9) onto the assembly to

create your second level.

*Ensure that the boards are

level and ush with each

other as you lay each one.

Fix every third board to the

one below by screwing

through the notch as shown

in the illustration using

1x70mm screw per side

(as outlined in Step 7).

**Ensure to stagger the screws

so as not to collide with the

previous screw.

20x70mm Screws

Step 11: Window Frame Fit

Once you have laid the second

level of boards onto the assembly

slide the window(s) between the

smaller boards and rest on to the

longer board.

*Ensure the boards are level with

each end.

*Please note: This image is for

illustrative purposes and may

dier from your choice in product

(regarding window position).

Nevertheless the process of tting

the window is the same.

Pre drill

hole

70mm

screw

IMPORTANT: It is imperative that you pre-drill before xing screws.

IMPORTANT: It isimperative that

you pre-drill before xing screws.

P 6

Please retain product label and instructions for future reference

Step 12 (See Pre-Assembly)

Following the same method

outlined in Pre-Assembly, lay

the remaining boards (No’s. 6, 7,

9, 10 & 11) onto the assembly

to bring the board level to the

top of the window and door

frames.

*Ensure that the boards are

level and ush with each

other as you lay each one.

Fix every third board to the

one below by screwing

through the notch as shown

in the illustration using

1x70mm screw per side

(as outlined in Step 7).

**Ensure to stagger the screws

so as not to collide with the

previous screw.

20x70mm Screws

Pre drill

hole

70mm

screw

Step 13 (See Pre-Assembly)

Following the same method

outlined in Pre-Assembly, lay

the last two boards (No. 6)

onto the front of the assembly.

Once in position place log

board WA (No. 12) onto the

window and plain side,

xing into position by screwing

through the notches as shown

in the illustration.

*Ensure that the boards are

level and ush with each

other as you lay each one.

4x70mm Screws

Pre drill

hole

70mm

screw

Step 14 (See Pre-Assembly)

Place the gable tops onto the

assembly. Fix into position by

screwing through the notches

as shown in the illustration.

*Ensure that the boards are

level and ush with each

other as you lay each one.

4x70mm Screws

Pre drill

hole

70mm

screw

IMPORTANT: It is imperative that you pre-drill before xing screws.

12 6

Please retain product label and instructions for future reference

Pre drill

hole

Step 15: Ridge Bar Fit

Align the ridge bar(s) (No. 17) into the

cut out slots on each gable top ensuring

each ridge bar interlocks the boards.

Secure the ridge bars at each end by

screwing through the bars into the

boards (ensure to pre-drill to avoid

the boards splitting) using 4x70mm

screws per ridge bar.

*Please note: The gable shown is for

illustrative purposes and may dier

in width from your choice in product.

Nevertheless, despite any dierences

the process of xing the ridge bars

is the same.

12x70mm Screws

70mm

screw

Step 16

Place the rst two roof board’s

(No. 13) onto the assembly on

each side, making sure the boards

are ush to the end of the roof

purlin. Once in position x to each

purlin using 3x40mm screws.

*Ensure the roof boards meet

at the top of the apex and leave

an overhang at the bottom.

Continue adding the roof boards

along the roof, xing each one into

position using 3x40mm screws,

making sure that each board is

interlocked, ush at the bottom &

meet at the top of the apex.

The last board on each side will

overhang: Using a staight edge

and a pencil mark out a line as

a guide.

Cut along the pencil mark and

remove the excess. Place the

cut down board’s back onto the

roof and secure into place

using 3x40mm screws per

board.

*Please Note: This image is for

illustrative purposes and may

dier from your choice in product.

Nevertheless the process of

cutting and tting the last roof

board(s) is the same.

282x40mm Screws

40mm

screw

Pre drill

hole

*Cut to t

IMPORTANT: It is imperative

that you pre-drill before

xing screws.

23b 13

Please retain product label and instructions for future reference

Step 17

Ensuring the roof boards are ush

at the overhanging side and meet

at the apex, x the eaves frames

(No. 19) to the underside of the roof

boards using 18x40mm screws as

shown in the illustration

*Please Note: This image is for

illustrative purposes and may

dier from your choice in

product. Nevertheless the process

of xing the eaves frames is the

same.

36x40mm Screws

40mm

screw

Pre drill

hole

Step 18

Place the rst oor board (No. 14)

inside the building ush to the log

board on one side. Continue adding

the oor boards (internally) making

sure to interlock each individual

board.

*Do NOT secure the boards until

the last board has been measured

and cut.

Following the same method outlined

in Step 16 measure the gap between

the bottom of the tongue (on the last

board placed) and the log board.

Using a straight edge mark out the

measurement onto the last oor

board (No. 14) and cut along the

length removing the excess.

**Please note: Mark the nal board

2mm under the measurement; This

will allow the timber to expand and

contract correctly.

Once all the oor boards are in

position secure each board into

position using 13x40mm screws.

***Please Note: Ensure to screw

through eachof the oor boards

into the oor bearers.

442x40mm Screws

40mm

screw

Pre drill

hole

*Cut to t

Please retain product label and instructions for future reference

30mm

screw

HANDLE

WITH CARE

Felt

tacks

Step 21

Cut the felt into ve & strips lay onto

the roof in the order shown in the

illustration.

*Ensure there is approximately 50mm

of overhanging felt each side.

Once the felt is laid out x to the

roof using felt tacks at 100mm

intervals.

*Felt size: 5332mm

432x Felt Tacks

1. 2.

3. 4.

Roof

Internal Roof Trim

Internal

Step 19

Inside the building place an internal

roof trim (No. 24) against the boarding

and align with the roof as shown in the

illustration, ensuring the angled face

follows the roof line.

Once in position x each roof trim

into place using 40mm screws per

roof trim, equally spaced along the

face of the board.

28x40mm Screws

Pre drill

hole

40mm

screw

*trim to t

*Measure and cut the

interior roof trims to

t the internal space.

Step 20

Once the oor has been laid arrange the

skirting (No. 23) around the outside edge

of oor (internally), measure and cut down

accordingly to best match the internal

space.

Secure each skirting section into place

using 30mm spaced equally along the

board as shown in the illustration.

*Do NOT x the skirting to the oor

sheets/boards.

56x30mm Screws

30mm

screw 23

30mm

screw

Pre drill

hole

*Cut to t

*Internal view

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

Please retain product label and instructions for future reference

Step 22

Align the fascia’s (No. 18)

with the roof and x into

place using 3x40mm

screws per fascia, making

to screw through the

fascia into the roof purlins

and eaves frame.

*Ensure the angled cuts meet

at the top of the apex.

12x40mm Screws

Pre drill

hole

40mm

screw

Step 23

Arrange the storm braces (No. 22)

around the building (internally).

Place 2x storm braces per side

xing into place using 2x80mm

bolts per brace making sure the

washer & nut are tightened from

the outside of the building.

*Ensure the storm braces are

secured at the highest point

possible on each side.

**Storm braces will help your

building expand and contract

properly.

***It is imperative that each

bolt is tightened using a

washer so as not to damage

the log boards.

24x80mm Bolt Sets

Pre drill

hole

80mm

bolt

Dieses Handbuch passt für folgende Modelle

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01DDPENT1008-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHCR0707FGD2TW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01TDM0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02DTSHOA0705LFD3WBF-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG015-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03HEL1008DDFW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02DTTWRS0605-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02GARA0806-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTGRA0301-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03COR0707-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHPN0407DSHSA-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products GROUNDSMAN 10 X 8 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0628PNNE0325HGDD1SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTOSBA0306DDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 10DTSHPN0804-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTOVAX0806DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products Rose Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Groundsman Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHDB1008DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628WKNE0304LBDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 05DTOVPN0305DD-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03TGCORSE0408-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03WES0808-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1408DDOP-V1 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung