Mercia Garden Products 0628LOG181-V4 Bedienungsanleitung

P 1

0628LOG181-V4 (4x2.5m)

0628LOG181-V4: 4x2.5m (28mm) Pent log cabin with store

2mm Drill bit

Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied)

including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm

bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions.

For the duration of heavy or extended periods of rain, swelling of the wood panels may

occur. Warping of the wood may also occur during excessive dry spells due to an interior

moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is

suggested that the outdoor building is sprayed with water during extended periods of

warm sunshine and sheltered as much as possible during rain or snow.

BUILDING A BASE

When thinking about where the building and base are going to be constructed:

Ensure that there will be access (60cm) to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to

diagrams for the base dimensions. The base should be slightly smaller than the external

measurement of the building, i.e. The cladding should overlap the base, creating a run

o for water. It is also recommended that the oor be at least 25mm above the

surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the

case of childrens products independently tested to EN71 level, we cannot accept

responsibility for your safety whilst erecting or using this product.

Refer to the instructions pages for your specic product code

For ease of assembly use a

rubber mallet to t the log

boards. Do NOT use a heavy

hammer.

Ensure to measure and check before cutting

boards.

It is advisable to use a hand

saw when cutting roof and

oor boards.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

To ensure log boards are even, use a spirit

level to check each layer has been installed

correctly.

134.1

P 2

0628LOG181-V4

Overall Dimensions:

Width = 4064mm

Depth = 2731mm

Height = 2460mm

Base Dimensions:

Width = 3808mm

Depth = 2308mm

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Short Window Pack*

Log 181 Gable QTY 2

Gable is unxed for assembly purposes.

Starter Board - 28x66x4000mm QTY 2

LB28RT66-AF- 4000

Log Board - 28x120x630mm QTY 18

LB28-B-630

Log Board - 28x120x1800mm QTY 18

LB28-AE-1800

Log Board - 28x120x4000mm QTY 21

LB28-AF-4000

Log Board - 28x120x2500mm QTY 26

LB28-A-2500

Log Board - 28x120x560mm QTY 18

LB28-B-560

Log Board - 28x120x1120mm QTY 18

LB28-B-1120

Roof Board - 67x121x2706mm QTY 36

MB16-C-2706

Short Floor Board - 16x121x974mm QTY 20

MB16-C-974

Long Floor Board - 16x121x2746mm QTY 20

MB16-C-2746

Floor Bearer - 44x44x3808mm QTY 2

F4444-3808-PT

Floor Bearer - 44x44x2220mm QTY 14

F4444-2220-PT

Roof Purlin - 45x120x4004mm QTY 2

F45120-AF-4004

Eaves Frame - 27x44x4000mm QTY 2

F2744-4000mm

Front Fascia - 32x192x4064mm

AI-06LOG181-V1FF

Side Fascia - 32x192x2715mm QTY 2

AI-06LOG181-V1SF

Storage Door Pack*

Fascia Block - 27x44x245mm QTY 3

F2744-245

Double Door Pack*

Log 181 Gable QTY 1 (notched for door)

Gable is unxed for assembly purposes.

Storm Brace - 27x44x2000mm QTY 8

F2744-2000mm

Log Board - 115x28x4000mm

LB28RG115-AF-4000

Log Board - 28x120x875mm QTY 24

LB28-B-875

4.2

Felt

Pre-assembly

*Please note:

Each board interlocks at

either end in a staggered pattern.

Before securing ensure that the boards

are tted properly in their respective

tongues and grooves.

*All components for the Windows and Doors are

shown in the Windows and Doors instruction packs.

P 3

Please retain product label and instructions for future reference

Log Board - 120x28x4000mm

LB28-ADF-4000

Log Board - 120x28x2500mm

LB28-AD-2500

Felt Tacks x400

70mm Screw x91

Nail Bag

40mm Screw x494

30mm Screw x75

70mm Bolt Set x16

27 Closure Trim - 16x28x2400mm (approx length) QTY 13

S1628-2400

Roof Spacers QTY 5

PI-07-0208 (20x100x2mm)

Pre drill

hole

70mm

screw

P 4

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

Please retain product label and instructions for future reference

Step 1

Parts needed - No. 16 QTY 2

No. 17 QTY 2

Lay the bearers (No’s. 16 & 17)

onto a rm and level surface

(free from areas where

standing water can collect) as

shown in the illustration.

Fix the framing together at each

corner using 8x70mm screws,

ensuring the frame is ush.

8x70mm Screws

Pre drill

hole

70mm

screw

Step 2

Parts needed - No. 17 QTY 12

Following the same method

outlined in the previous step,

range the remaining bearers (No.

17) as shown in the illustration.

*Ensure there is an equal amount

of space between each frame.

Secure each of the frames in place

using 2x70mm screws for each

side of the bearer, ensuring the

framing remains level.

48x70mm Screws 17

*Before beginning assembly decide which side

you would like to place the storage section.

Depending on your preference ensure to align

the 5th oor bearer with the partition wall.

17 17 17 17 17

17 17

Pre drill

hole

70mm

screw

Step 3 (See Pre-Assembly)

Parts Needed - No. 5 QTY 2

No. 9 QTY 3

Place the Starter Boards (No. 5)

and the Log Boards (No. 9) on

to assembled base frame along

the longest sides.

*Ensure the notches at either

end of each board are ush

and level with the ends of the

frame.

Fix each of the starter boards to

the frame by screwing through

the notch into the frame as

shown in the illustration.

6x70mm Screws

IMPORTANT: Pre-drill before xing screws.

Step 4 (See Pre-Assembly)

Parts needed- No. 6 QTY 6

No. 7 QTY6

No. 8 QTY 6

No. 9 QTY 10

No. 11 QTY 6

No. 12 QTY 6

Following the same method

outlined in Pre-Assembly, lay

the rst 6 Log Boards (No’s. 6,

7, 8, 9, 11 & 12) onto the

starter boards to create your

rst level.

*Ensure that the boards are

level and ush with each

other as you lay each one.

Please Note: The short boards at the

front and side of the building (either

side of the door and window opening’s)

can be placed either side depending

on your needs.

12 9

IMPORTANT : Pre-drill before xing screws.

Example picture

2 screws per bearer per end

P 5

Please retain product label and instructions for future reference

Step 6(See Pre-Assembly)

Parts needed - No. 6 QTY 6

No. 7 QTY6

No. 8 QTY 6

No. 9 QTY 6

No. 10 QTY 14

No. 11 QTY 7

No. 12 QTY 7

Following the same method

outlined in Pre-Assembly , lay

the next Log Boards (No’s. 6, 7,

8, 9, 10,11 & 12) onto the

assembly to create your second

level.

*Ensure that the boards are

level and ush with each

other as you lay each one.

*Doors can be hung once the

boarding has enclosed the

door frame by 12-13 boards,

refer to door installation

instructions, if not, you can

install the door at step 8.

***Please Note: The short boards placed

to create the opening’s for the doors &

windows can be placed either side

depending on your needs.

Step 5

Once you have laid 6 log boards (o

of the starter ) up the door section,

slide the assembled door frames for

the double door and storage door

(No. 2 & 3)over the boards resting the

frame on top of the starter board.

*Please note:This image is for illustra -

tive purposes and may dier from

your choice in product ( regarding

door position). Nevertheless the

process of tting the door frame is

the same.

**Please Note:The short boards at

the

front of the building (either side of

the door and window opening’s) can

be placed either side depending on

your needs.

P 6

Please retain product label and instructions for future reference

Step 8(See Pre-Assembly)

Parts needed -No. 6 QTY 6

No. 7 QTY6

No. 8 QTY 6

No. 9 QTY 6

No. 10 QTY 10

No. 11 QTY 6

No. 12 QTY 6

No. 26 QTY 1

Following the same method

outlined in Pre-Assembly , lay

the remaining Log Boards

(No’s. 6, 7, 8, 9, 10, 11,12 & 26)

onto the assembly to bring the

board level to the door frames.

*Ensure that the boards are

level and ush with each

other as you lay each one.

*Doors can be hung once the

boarding has enclosed the

door frame.

Step 7

Once you have laid the second

level of boards onto the assembly

slide the window(s)(No. 1) between the

smaller boards and rest on to the

longer board.

*Ensure the boards are level with

each end.

*Please note: This image is for

illustrative purposes and may

dier from your choice in product

(regarding window position).

Nevertheless the process of tting

the window is the same.

Step 9 (See Pre-Assembly)

Parts needed - No. 4.1C QTY 2

No. 4.2 C QTY 1

No. 8 QTY 2

No. 24 QTY 1

No. 25 QTY 1

Place the next Log

Boards (No. 8 & 25) onto the

rear and front of the building as

shown in the diagram.

4.1c

4.2c

4.1c

Once in position, place the

rst board of the gables (No’s 4.1C

& 4.2C)onto the assembly xing

with 2x70mm screws.

Then add the last two Boards

(No’s 8 & 24) onto the front and

rear of the building as shown in

the diagram.

*Ensure that the boards are

level and ush with each

other as you lay each one.

P 7

Please retain product label and instructions for future reference

Pre drill

hole

Step 11

Parts needed - No. 18 QTY 2

Align the Purlin(s) (No. 18) into

the cut out slots on each gable top

ensuring each perlin interlocks the

boards.

Secure the purlins at each end

by screwing through the bars into the

boards using 6x70mm screws per

purlin.

*Please note:The gable shown is for

illustrative purposes and may dier

in width from your choice in product.

Nevertheless, despite any dierences

the process of xing the Purlins

is the same.

12x70mm Screws

70mm

screw

Step 10 (See Pre-Assembly)

Parts needed - No. 4.1A QTY 2

No. 4.1B QTY 2

No. 4.2A QTY 1

No. 4.2B QTY 1

No. 8 QTY 1

Following the same method,

add the next boards of the

gables (No. 4.1b & 4.2b) onto

the panels as shown in the

diagram. Secure the boards in

place using 2x70mm screws per

board.

Place the nal log board (No. 8)

onto the front of the assembly

and screw down with 2x70mm

screws.

Then add the nal boards of the

gables (No. 4.1a & 4.2a) onto

the panels as shown in the

diagram. Secure the boards in

place using 2x70mm screws per

board.

*Ensure that the boards are

level and ush with each other

as you lay each one.

14x70mm Screws

Pre drill

hole

70mm

screw

IMPORTANT: Pre-drill before xing screws.

4.1b

4.1a

4.1b

4.1a

4.2b

4.2a

IMPORTANT: Pre-drill before xing screws.

P 8

Please retain product label and instructions for future reference

Step 13

Parts needed - No. 19 QTY 2

Ensuring the roof boards are

ush at the overhanging sides, x

the Eaves Frames (No. 19) to the

underside of the roof boards

using 9x40mm screws as shown

in the

illustration.

*Please Note:This image is for

illustrative purposes and may

dier from your choice in

product. Nevertheless the

process

of xing the eaves frames is the

same.

18x40mm Screws

40mm

screw

Pre drill

hole

Step 12

Parts needed - No. 13 QTY 36

Place the rst two roof board’s (No.

13) onto the assembly on each side,

making sure the boards are ush to

the end of the roof purlin. Once in

position x to each purlin using

4x40mm screws.

Due to natural occurences of wood

shrinkage / expansion. You maybe

required to use the provided spac-

ers and place a space of 2mm to

ensure every roof board lines up

with the truss’.

Continue adding the roof boards

along the roof, xing each one into

position using 4x40mm screws,

making sure that each board is

interlocked, ush at the bottom.

The last board on each side will

consist of a tongue and groove

overhang: Using a straight edge

and a pencil mark out a line as

a guide.

Cut along the pencil mark and

remove the excess. Place the cut

down board’s back onto the roof

and secure into place using

4x40mm screws per board.

*Please Note:This image is for

illustrative purposes and may

dier from your choice in product.

Nevertheless the process of

cutting and tting the last roof

board(s) is the same.

144x40mm Screws

40mm

screw

Pre drill

hole

*Cut to t

IMPORTANT: Pre-drill before xing screws. IMPORTANT: Pre-drill before xing screws.

P 9

Please retain product label and instructions for future reference

Step 14

Parts needed - No. 14 QTY 20

No. 15 QTY 20

Place the rst Short Floor Board (No.

14) inside the building ush to the

log board on one side. Continue

adding the oor boards (internally )

making sure to interlock each

individual board. Repeat this with the

Long Floor Boards (No. 15).

*Do NOTsecure the boards until

the last board has been measured

and cut.

Following the same method outlined,

measure the gap between the

bottom of the tongue (on the last

board placed) and the log board.

Using a straight edge mark out the

measurement onto the last oor

board and cut along the length

removing the excess.

**Please note:Mark the nal board

2mm under the measurement; This

will allow the timber to expand and

contract freely.

Once all the oor boards are in

position secure each board into

position using 8x40mm screws.

***Please Note:Ensure to screw

through each of the oor boards

into the oor bearers.

320x40mm Screws

40mm

screw

Pre drill

hole

*Cut to t

Step 15

Parts needed - No. 20 QTY 3

No. 27 QTY 2

Attach the Fascia

Blocks (No. 20) to the front of

the building, ensuring the

blocks are ush to the eaves

frame.

*Tip: Use the front fascia as

guide to mark out the

position for the blocks.

Fix 3 x blocks on the outside

of the building as detailed in

the image.

3x70mm Screws

70mm

screw

*External

On the sides of the building,

roughly measure the gap between

each purlin and cut 6 pieces out of

2 closure trims (No. 27).

Then x to the underside of

the roof inbetween the purlins on

both sides of the building as shown

in the illustration. Secure the

framing into place using 2x40mm

screws, ensuring to screw down

through the roof into the frames.

*Please note: These sections of

framing are to help secure the

felt to your building.

12x40mm Screws

40mm

screw

Pre drill

hole

*Cut to t

Step 8(See Pre-Assembly)

Parts needed -No. 6 QTY 6

No. 7 QTY6

No. 8 QTY 6

No. 9 QTY 6

No. 10 QTY 10

No. 11 QTY 6

No. 12 QTY 6

No. 26 QTY 1

Following the same method

outlined in Pre-Assembly , lay

the remaining Log Boards

(No’s. 6, 7, 8, 9, 10, 11,12 & 26)

onto the assembly to bring the

board level to the door frames.

*Ensure that the boards are

level and ush with each

other as you lay each one.

*Doors can be hung once the

boarding has enclosed the

door frame.

IMPORTANT: Pre-drill before xing screws.

P 10

Please retain product label and instructions for future reference

HANDLE

WITH CARE

Felt

tacks

Step 18

Parts needed - No. 28

Cut the felt (No. 28) into four

strips & lay onto the roof in the

order shown in the illustration.

*Ensure there is approximately

50mm of overhanging felt

each side.

Once the felt is laid out, x to

the roof using felt tacks at

100mm intervals.

*Felt size: 4164mm

210x Felt Tacks

1. 2. 3. 4.

IMPORTANT : Pre-drill before xing screws.

Roof

Closure Trim

Internal

*Measure and cut the

closure trims to

t the internal space.

Roof

Closure Trim

Internal

*Measure and cut the

closure trims to

t the internal space.

Pre drill

hole

30mm

screw

*trim to t

Step 16

Parts needed - No. 27 QTY 5

Inside the building place the closure

trim (No. 27) against the boarding

and align with the roof as shown in

the illustration.

Once in position x each trim

into place by pre drilling a pilot hole

and using 6x30mm screws per trim,

equally spacing them along the face

of the board.

30x30mm Screws

30mm

screw

Pre drill

hole

*Cut to t

Step 17

Parts needed - No. 27 QTY 6

Once the oor has been laid arrange the

closure trim (No. 27) around the outside

edge of oor (internally), measure and cut

down accordingly to best match the

internal space.

Secure each trim section into place using

6x30mm spaced equally along the board

as shown in the illustration.

*Do NOT x the closure trim to the oor

boards.

36x30mm Screws

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01DTOVAX0806DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 04GREEN0806SD-V6 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01SHPWOR1210DDOW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA1006DDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02GARA0806-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01RAW2010DDOW-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Wessex 03WES1208-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01GRODB1008-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01SHPSTR0402-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products HONEYSUCKLE PLAYHOUSE Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01GRO1008DD-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04GREEN0606SD-V5 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OSBRA0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01SHPWOR1010DDOW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01RAW1010DDOW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634LOG209-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 10DTDRK0806-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0644CSNE0303HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTSHPWOR1010DDOW-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTGRO1006DD-V3 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products Wessex 03WES0808-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHHP0806HGD4MW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTOVAX0604SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPA0705SDFW-V1 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung