Metrohm 856 Bedienungsanleitung

856 Conductivity Module

Manual

8.856.8005EN / 2020-02-11

Metrohm AG

CH-9100 Herisau

Switzerland

Phone +41 71 353 85 85

Fax +41 71 353 89 01

[email protected]

www.metrohm.com

856 Conductivity Module

Manual

8.856.8005EN / 2020-02-11

Technical Communication

Metrohm AG

CH-9100 Herisau

[email protected]

This documentation has been prepared with great care. However, errors

can never be entirely ruled out. Please send comments regarding possible

errors to the address above.

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ Table of contents

856 Conductivity Module ￭￭￭￭￭￭￭￭ III

Table of contents

1 Introduction 1

1.1 Conductivity Module system ............................................... 1

1.2 Instrument description ......................................................... 2

1.3 Measuring modes and commands ...................................... 2

1.4 About the documentation ................................................... 3

1.4.1 Symbols and conventions ........................................................ 3

1.5 Safety instructions ................................................................ 4

1.5.1 General notes on safety ........................................................... 4

1.5.2 Electrical safety ........................................................................ 4

1.5.3 Working with liquids ................................................................ 5

1.5.4 Recycling and disposal ............................................................. 5

2 Overview of the instrument 6

3 Installation 8

3.1 Setting up the instrument .................................................... 8

3.1.1 Packaging ................................................................................ 8

3.1.2 Checks .................................................................................... 8

3.1.3 Location .................................................................................. 8

3.2 Connecting a controller ........................................................ 8

3.2.1 Operation ................................................................................ 8

3.3 Connecting MSB devices .................................................... 13

3.3.1 Connecting a dosing device ................................................... 14

3.3.2 Connecting a stirrer or titration stand .................................... 15

3.3.3 Connecting a Remote Box ..................................................... 16

3.4 Connecting USB devices ..................................................... 17

3.4.1 General ................................................................................. 17

3.4.2 Connecting a USB hub ........................................................... 18

3.4.3 Connecting a printer .............................................................. 18

3.4.4 Connecting a balance ............................................................ 19

3.4.5 Connecting a PC keyboard (only for operation with Touch

Control) ................................................................................. 20

3.4.6 Connecting a barcode reader ................................................. 21

3.5 Connecting sensors ............................................................ 22

3.5.1 Connecting a conductivity measuring cell .............................. 22

4 Operation and maintenance 24

4.1 Care ...................................................................................... 24

4.2 Maintenance by Metrohm Service .................................... 24

Table of contents ￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭

IV ￭￭￭￭￭￭￭￭ 856 Conductivity Module

5 Troubleshooting 25

5.1 General ................................................................................ 25

6 Appendix 26

6.1 Remote interface ................................................................ 26

6.1.1 Pin assignment of the remote interface .................................. 26

7 Technical specifications 30

7.1 Measuring interface ........................................................... 30

7.1.1 Conductivity .......................................................................... 30

7.1.2 Temperature .......................................................................... 30

7.2 Power connection ............................................................... 31

7.3 Ambient temperature ......................................................... 31

7.4 Reference conditions .......................................................... 31

7.5 Dimensions .......................................................................... 31

7.6 Interfaces ............................................................................. 32

8 Accessories 33

Index 34

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ Table of figures

856 Conductivity Module ￭￭￭￭￭￭￭￭ V

Table of figures

Figure 1 856 Conductivity Module system ....................................................... 1

Figure 2 Front 856 Conductivity Module ......................................................... 6

Figure 3 Rear 856 Conductivity Module .......................................................... 7

Figure 4 Connecting the Touch Control ........................................................... 9

Figure 5 Connecting the computer ................................................................ 12

Figure 6 MSB connections ............................................................................ 13

Figure 7 Connecting a dosing device ............................................................. 15

Figure 8 Connecting an MSB stirrer ............................................................... 16

Figure 9 Connecting the rod stirrer to the titration stand ............................... 16

Figure 10 Connecting the Remote Box ............................................................ 17

Figure 11 Connecting a printer ....................................................................... 19

Figure 12 Connecting a conductivity measuring cell ........................................ 22

Figure 13 Connecting the adapter box ............................................................ 23

Figure 14 Connecting the conductivity measuring cell to the adapter box ....... 23

Figure 15 Connectors of the Remote Box ........................................................ 26

Figure 16 Pin assignment of remote socket and remote plug ........................... 26

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 1 Introduction

856 Conductivity Module ￭￭￭￭￭￭￭￭ 1

1 Introduction

1.1 Conductivity Module system

MSB

Controller

PC Keyboard

Barcode

Reader

USB/RS-232 Converter

Touch Control

USB Sample Processor

Robotic Titrosampler

USB Hub

Relay Box

Remote Box

Balance

Dosing Interface

Dosino

Stirrer / Ti Stand

Dosimat

Status

Titrando

USB 856 Conductivity

Module

Cond. cell

Sensors

Printer

Tower-PC

Figure 1 856 Conductivity Module system

1.2 Instrument description ￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭

2￭￭￭￭￭￭￭￭ 856 Conductivity Module

1.2 Instrument description

Conductivity measurements can be performed with the 856 Conductivity

Module.

The 856 Conductivity Module has the following characteristics:

￭Operation

A touch-screen Touch Control or a high-performance PC software is

used for operation.

￭Dosing

Dosinos or Dosimats can be used for dosing.

￭MSB connectors

Four MSB connectors (Metrohm Serial Bus) for connecting dosing devi-

ces (Dosimat with exchange unit or Dosino with dosing unit), stirrers,

titration stands and Remote Boxes.

￭USB connectors

Two USB connectors, with which devices such as printers, PC key-

boards, barcode readers or additional control instruments (USB Sample

Processor, Titrando, Dosing Interface, etc.) can be connected.

￭Measuring interface

One measuring input for a conductivity measuring cell with integrated

temperature sensor.

1.3 Measuring modes and commands

The following measuring modes and commands are supported:

￭MEAS

The following measuring modes can be selected for measurements:

–Cond (conductivity measurement)

–T (temperature measurement)

￭CAL

Calibration.

–Cond (determination of the cell constant of a conductivity mea-

suring cell)

￭Dosing commands

The following commands for dosing can be selected:

–PREP (rinsing the cylinder and tubings of an exchange unit or

dosing unit)

–EMPTY (emptying the cylinder and tubings of a dosing unit)

–ADD (dosing a specified volume)

–LQH (carrying out complex dosing tasks with a Dosino)

Inhaltsverzeichnis

Andere Metrohm Laborausrüstung Handbücher

Metrohm

Metrohm 838 Advanced Sample Processor Gebrauchs- und Pflegehandbuch

Metrohm

Metrohm 870 KF Titrino plus Bedienungsanleitung

Metrohm

Metrohm 728 Bedienungsanleitung

Metrohm

Metrohm 760 Bedienungsanleitung

Metrohm

Metrohm 700 Dosino Bedienungsanleitung

Metrohm

Metrohm 850 Professional IC Bedienungsanleitung

Metrohm

Metrohm 873 Biodiesel Rancimat Bedienungsanleitung

Metrohm

Metrohm 889 IC Sample Center Basic Bedienungsanleitung

Metrohm

Metrohm 940 Professional IC Vario ONE/SeS/PP/MB Bedienungsanleitung

Metrohm

Metrohm 802 Stirrer Bedienungsanleitung

Metrohm

Metrohm 930 Compact IC Flex ChS/Deg Bedienungsanleitung

Metrohm

Metrohm 785 DMP Titrino Bedienungsanleitung

Metrohm

Metrohm 870 KF Titrino plus Betriebsanleitung

Metrohm

Metrohm 893 Bedienungsanleitung

Metrohm

Metrohm 846 Bedienungsanleitung

Metrohm

Metrohm OMNIS 2.1006.00X0 Bedienungsanleitung

Metrohm

Metrohm 859 Titrotherm Bedienungsanleitung

Metrohm

Metrohm 790 Personal IC Bedienungsanleitung

Metrohm

Metrohm 940 Professional IC Vario Series Bedienungsanleitung

Metrohm

Metrohm 823 Membrane Pump Unit Bedienungsanleitung

Metrohm

Metrohm 804 Ti Stand Bedienungsanleitung

Metrohm

Metrohm OMNIS 2.1002.0 10 Series Bedienungsanleitung

Metrohm

Metrohm Dosimat plus 876 Bedienungsanleitung

Metrohm

Metrohm Combustion-IC-System Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung