Miele S176i Bedienungsanleitung

Operating Instructions

Vacuum Cleaner

S176i, S177i

Please carefully study these Operating Instructions before attempting to operate the

unit and note the listed Important Safety Instructions.

When using this vacuum cleaner, basic precautions should always be followed , including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER

WARNING To reduce the risk of fire, electric shock, or injury:

• Do not leave vacuum cleaner unattended when it is plugged in. Unplug it from the outlet when not in use

and before servicing.

• Electric shock could occur if used outdoors or on wet surfaces.

• Do not allow to be used as a toy. Close attention is necessary when used by or near children.

• Use only as described in this manual. Use only manufacturer’s recommended attachments.

• Do not use with damaged cord or plug. If the vacuum cleaner is not working as it should, has been

dropped, damaged, left outdoors, or dropped into water, bring it to a service center.

• Do not pull or carry by cord, use the cord as a handle, close a door on the cord, or pull the cord around

sharp edges or corners. Do not run the vacuum cleaner over the cord. Keep the cord away from heated

surfaces.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Do not handle the plug or vacuum cleaner with wet hands.

• Do not put any object into the openings. Do not use with any opening blocked. Keep openings free of

dust, lint, hair, and anything that may block or reduce air flow.

• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.

• Do not use without dust bag and/or filters in place.

• Turn off all controls before unplugging.

• Use extra care when cleaning on stairs.

• Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they

may be present.

SAVE THESE INSTRUCTIONS

THIS VACUUM CLEANER IS INTENDED FOR HOUSEHOLD USE ONLY

Notice- Before you plug in your Vacuum Cleaner, make sure that the voltage indicated on the rating plate

located at the rear of the vacuum cleaner is the same as your local supply.

IMPORTANT SAFETY INSTRUCTIONS

IDENTIFICATION OF MAIN PARTS

A-1) Handle

H) Bag change indicator

B-2) Cord clip

C) ON/OFF Switch

Dust bag cover

E) Foot pedal

F) Beater bar selector

Carry handle

J) Clean air filter

Bumper

Cleaning head

Head-light (S177i only)

D) Variable power control

(S177i only)

A-3) Upper cord

hook

B-1) Power cord

A-2) Hose clip

A-3) Lower

cord hook/

Carrying

handle

I) Paper bag

Extension tube

Crevice nozzle

Dusting brush Hose

Hose clip

A) HANDLE ASSEMBLY

C) ON / OFF SWITCH

To start or stop the vacuum cleaner,

push the switch to “I” to turn it ON, and

to “O” to turn it OFF.

B) POWER CORD STORAGE

NOTE: To reduce the risk of electric shock, this appliance

has a polarized plug (one blade is wider than the other). This

plug will fit in a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the plug. If it still does

not fit, contact a qualified electrician to install the proper

outlet. Do not change the plug in any way.

To avoid any possible damage to the power cord, never run

over the cord or allow it to become caught in the rotary

brush.

HOW TO ASSEMBLE / OPERATE YOUR CLEANER

1) Insert the base of the handle

into the top of the body of the

machine as shown. Push down

the handle and tighten the screw.

2) Set the hose around the hose

clip.

3) Turn the upper cord hook to

the upright position and wind the

power cord around the upper

and lower cord hooks.

IMPORTANT: Do not over

tighten the screw.

1) Turn the upper hook to

release the power cord

for instant use.

2) Set the power cord into

the cord clip to help

secure it during use

IN MAX

Hose clip

Upper cord hook

Lower

cord hook/

Carrying

handle

E) USING THE FOOT PEDAL TO ADJUST THE VACUUM HEIGHT

To lower the body of the cleaner, step on the pedal at the left rear corner of the vacuum cleaner.

D) VARIABLE POWER CONTROL (S177i Only)

1. Upright position

The handle should be in an

upright position when cleaning

tools are used.

2. Middle position

For normal cleaning, press the

foot pedal and pull back the

handle to a comfortable angle.

3. Low position

For cleaning under furniture,

press the pedal a second

time. The handle may now be

lowered almost to the floor as

shown.

MIN MAX

MC-E452

MIN: To clean curtains and soft furnishings

with tool attached.

MAX: To continuously clean with

high suction power.

This vacuum cleaner incorporates a variable power control to allow you to select the power most suitable

for your cleaning needs.

F) BEATER BAR SELECTOR

When cleaning carpeted floor, slide the selector to the

“BEATER BAR” position. To stop the beater bar while

using accessories, slide the selector to the “STOP”

position.

NOTE: The vacuum cleaner should be running when

changing the position of the BEATER BAR

SELECTOR.

B E A T E R

B A R

S T O P

BEATER BAR ON OR OFF

G) HOW TO USE THE ACCESSORIES

1) To use the accessories keep the vacuum cleaner

upright and slide the BEATER BAR SELECTOR to

the “STOP” position.

2) Pull the hose out of the intake port a the lower left

of the vacuum, and release it from the hose clip.

Connect the desired accessory as illustrated

below.

3) When finished using the accessory, re-insert the

hose end into the intake port and place the hose

under the clip. The accessories can also be

returned to their storage locations.

Hose clip

CAUTION: While using the accessories, hold

the handle as shown above to avoid pulling

the cleaner over.

I) REPLACING THE DUST BAG

H) BAG CHANGE INDICATOR

CAUTION: DISCONNECT THE CLEANER FROM THE OUTLET BEFORE

PERFORMING THE OPERATIONS BELOW

The bag change indicator located on the

front of your cleaner normally indicates

when the dust bag should be changed. In

order to maintain the best efficiency, it

should be changed when the yellow mark

appears in the window.

NOTE: if the yellow mark appears after the

bag has been replaced, check to see if the

hose or suction tube is clogged (see

BLOCKAGES). Due to the smaller intake,

the yellow mark may also appear when

using the crevice tool.

1) Remove the dust cover

by pulling it forwards.

2) Grip the cardboard of

the dust bag and pull

the bag out of the dust

compartment.

3) Install the new dustbag

by placing the hole over

the exhaust port and

pressing it into place as

shown.

IMPORTANT: For

maximum vacuum

efficiency, dustbags

should be changed

regularly.

Yellow

mark

Bag change

indicator

We recommend the use of genuine Miele paper bags only

Part # 5294740 Type Z

NOTE: If the dust bag is installed incorrectly,

the dust cover will not close.

J) CHANGING FILTERS

TROUBLE SHOOTING GUIDE

Before returning the vacuum cleaner to a Miele Service Center, check the

following items:

Problem Check Point Cause / Remedy

Motor doesn’t run.

(no noise is heard at all)

Motor runs but no suction.

Beater bar does not rotate.

• Cord connection.

• Hose inlet clogged.

• Check the bag change indicator.

• Paper bag broken or clogged.

• Central filter.

• Beater bar selector.

• Beater bar / housing.

• Belt broken or loose.

• Plug cord into outlet correctly.

• I If there is a clog, remove it.

• If it shows full, replace the paper

bag.

• If the paper bag is broken, replace it.

• If the central filter is full of dust, clean

or replace it.

• Select the correct position.

• If there is an obstruction, remove it.

• Replace the belt.

In addition to the dustbag, the vacuum cleaner

contains two filters; a central filter that protects the

motor (fig.1) and an electrostatic, “Clean Air” filter

that removes particles from the exhausted air

(fig.2). The Clean Air filter should be changed every

six months or whenever it becomes dirty. The

central filter should be changed or rinsed out

whenever the Clean Air filter is replaced.

CENTRAL FILTER (Fig. 1)

Part # F0391100

To remove, slide the central filter forward out of its

housing.

IMPORTANT: If the central filter has been rinsed

out, make sure it is dry before re-installing it.

CLEAN AIR FILTER (Fig. 2)

Part # S02B0100

To change the Clean Air filter.

1) Remove the dust compartment cover.

2) Slide the filter support out of the bottom of the

cover and remove the filter.

IMPORTANT: Do not forget to re-install the filters before use.

Fig. 1

Fig. 2

MAINTENANCE FOR THE BEATER BAR

BLOCKAGES

If your cleaner stops picking up dust, or the Bag Change Indicator shows "Full" while the dust bag

is still empty, a blockage may have occurred.

To remove the obstruction, proceed as follow:

Remove the hose from the suction inlet by turning the hose to the right and pulling it out (Fig. 1). Clear any

obstruction from the hose and/or suction inlet using a blunt instrument, taking care not to damage the hose.

If the obstruction occurs in the suction pipe, it can be removed with care as shown in Fig. 2.

IMPORTANT NOTE: Before replacing any part always,

DISCONNECT THE CLEANER FROM THE ELECTRICAL SUPPLY.

Suction pipe inlet

DO NOT USE YOUR FINGERS OR HANDS TO

REMOVE OR CLEAN THE BEATER BAR.

When it is necessary to remove thread, string, hair

etc., which has wound around the beater bar, cut

across them with a pair of scissors, making sure

not to cut the brush.

REMOVEPLUGBEFORE

REMOVINGTHIS COVER

REMOVEPLUGBEFORE

REMOVINGTHIS COVER

Fig. 1 Fig. 2

SERVICING AND REPAIRS

Use only genuine Miele replacement parts.

DISCONNECT THE CLEANER FROM THE ELECTRICAL SUPPLY

If you have any questions, contact your local dealer / service agent.

Any service needed other than that described in these Operating Instructions should be

performed by a Miele Service Center, only.

To replace any of the following parts, place the vacuum cleaner in the horizontal position

by using the pedal. Then turn it over exposing the underside.

HOW TO REPLACE - DRIVE BELT

(#S01R4000) AND BEATER BAR ASSEMBLY

(Part # R98G1064)

1. Remove the 4 screws from the base plate and

lift it off. (Fig. 1)

2. Release the belt from the motor shaft and lift

the beater bar assembly to remove the belt.

(Fig. 2)

3. To reassemble the beater bar, return

the belt to the motor shaft and beater bar

pulley.

Re-insert the bar into its supports and turn the

beater bar to ensure that the belt is seated

correctly. (Fig. 3)

4. Replace the base plate, and re-fasten the

screws securely.

HOW TO REPLACE - BEATER BAR / SIDE

BRUSHES / SHAFT SUPPORT A-B

1. First remove the base plate, drive belt and

beater bar assembly (as illustrated above).

2. Remove the 2 screws at both ends of the

beater bar assembly and separate the

different parts as shown in the exploded view.

3. Replace any damaged part and reassemble in

the reverse order.

REPLACING THE HEAD-LIGHT BULB

(S177i only)

1. Remove the base plate, release the head-

light assembly and lift it off. (Fig. 1)

2. Remove the old bulb, and replace it with a

new one (Fig. 2)

(Consult your dealer / service agent for a

suitable replacement bulb).

3. Re-insert the head-light assembly and the

base plate.

REMOVEPLUGBEFORE

REMOVINGTHIS COVER

Fig. 2

Screw

Side

Brush

Side

Brush

Rotary brush

Shaft

support

Shaft

support

Fig. 3Fig. 1

Fig. 2Fig. 1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Miele Staubsauger Handbücher

Miele

Miele S 6390 Bedienungsanleitung

Miele

Miele 10354220 Bedienungsanleitung

Miele

Miele VACUUM CLEANER S240I Bedienungsanleitung

Miele

Miele HS18 Bedienungsanleitung

Miele

Miele S7280 Bedienungsanleitung

Miele

Miele S157 Bedienungsanleitung

Miele

Miele S 5981 PowerPlus Bedienungsanleitung

Miele

Miele HS15 Bedienungsanleitung

Miele

Miele HS15 Bedienungsanleitung

Miele

Miele HS14 Bedienungsanleitung

Miele

Miele HS14 Bedienungsanleitung

Miele

Miele S 447i Bedienungsanleitung

Miele

Miele Dynamic U1 Bedienungsanleitung

Miele

Miele HS05 Bedienungsanleitung

Miele

Miele S157 Bedienungsanleitung

Miele

Miele S 8000 Bedienungsanleitung

Miele

Miele Compact C2 PARQUET ECOLINE Bedienungsanleitung

Miele

Miele HS18 Bedienungsanleitung

Miele

Miele Blizzard CX1 Comfort EcoLine Bedienungsanleitung

Miele

Miele Triflex HX1 Pro Bedienungsanleitung

Miele

Miele TX2070 Bedienungsanleitung

Miele

Miele S 6000 Bedienungsanleitung

Miele

Miele SEB 215 Bedienungsanleitung

Miele

Miele TANGO ECOLIN 4225660 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung