MikroTik RouterBOARD SXT 5HnD Bedienungsanleitung

RouterBOARD SXT 5HnD

User's Manual

(Rev.6; 27-Jan-2011)

Co yright MikroTikls SIA. This manual contains information

rotected by co yright law. No art of it may be re roduced or

transmitted in any form without rior written ermission from the

co yright holder.

Trademarks

RouterBOARD, RouterOS, RouterBOOT and MikroTik are trademarks

of MikroTikls SIA. All trademarks and registered trademarks

a earing in this manual are the ro erty of their res ective

holders.

Limited Warranty

co yright law. No art of it may be re roduced or transmitted in any form without rior written ermission

from the co yright holder. RouterBOARD, RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls

SIA. All trademarks and registered trademarks a earing in this manual are the ro erty of their res ective

holders.

Hardware. MikroTik warrants all RouterBOARD series equi ment for the term of fifteen (15) months from the

shi ing date to be free of defects in materials and workmanshi under normal use and service, exce t in

case of damage caused by mechanical, electrical or other accidental or intended damages caused by

im ro er use or due to wind, rain, fire or other acts of nature.

To return failed units to MikroTik, you must erform the following RMA (Return Merchandise Authorization)

rocedure. Follow the instructions below to save time, efforts, avoid costs, and im rove the s eed of the

RMA rocess.

1.If you have urchased your roduct from a MikroTik Reseller, lease contact the Reseller com any

regarding all warranty and re air issues, the following instructions a ly ONLY if you urchased your

equi ment directly from MikroTik in Latvia.

2. We do not offer re airs for roducts that are not covered by warranty. Exce tions can be made for

RB1000 and RB1100.

3. Out-of-warranty devices and devices not covered by warranty sent to Mikrotikls will be returned to the

sender at sender's cost.

Instructions are located on our web age here: http://rma.mikrotik.com

Manual. This manual is rovided “as is” without a warranty of any kind, ex ressed or im lied, including, but

not limited to, the im lied warranty of merchantability and fitness for a articular ur ose. The manufacturer

has made every effort to ensure the accuracy of the contents of this manual, however, it is ossible that it

may contain technical inaccuracies, ty ogra hical or other errors. No liability is assumed for any inaccuracy

found in this ublication, nor for direct or indirect, incidental, consequential or other damages that may

result from such an inaccuracy, including, but not limited to, loss of data or rofits. Please re ort any

inaccuracies found to su [email protected].

RouterBOARD SXT Series User's Manual rev. 6

Table of Contents

Co yright....................................................................................................................................... 1

Trademarks.................................................................................................................................... 1

Limited Warranty............................................................................................................................. 1

System Board View......................................................................................................................... 3

System Board Layout....................................................................................................................... 3

S ecifications................................................................................................................................. 4

Hardware Guide.............................................................................................................................. 4

LAN1 Port with PoE................................................................................................................. 4

LEDs..................................................................................................................................... 4

Onboard 802.11a/n 5GHz wireless............................................................................................ 5

Built in antenna...................................................................................................................... 5

USB ort............................................................................................................................... 5

User's Guide................................................................................................................................... 6

First use................................................................................................................................ 6

Grounding............................................................................................................................. 6

Powering............................................................................................................................... 6

Mounting............................................................................................................................... 6

Booting o tions...................................................................................................................... 7

Onboard NAND Storage Device................................................................................................. 7

Booting from network.............................................................................................................. 7

RouterBOOT........................................................................................................................... 8

Boot Loader Configuration........................................................................................................ 8

Boot Loader U grading............................................................................................................ 8

O erating System Su ort....................................................................................................... 8

Connector Index..................................................................................................................... 8

Button Index.......................................................................................................................... 9

Ethernet Cables...................................................................................................................... 9

Federal Communication Commission Interference Statement

(FCC ID: TV7SXT-5D).............................................................................................................. 9

RouterBOARD SXT Series User's Manual rev. 6

System Board iew

System Board Layout

Chain 0

RouterBOARD SXT Series User's Manual rev. 6

Specifications

RouterBOARD SXT 5HnD

CPU AR7241 400MHz

Memory 32MB DDR SDRAM

Boot loader RouterBOOT

Data storage 64MB onboard NAND memory chi

Ethernet One 10/100 with Auto-MDI/X

Wireless Built-in 5GHz 802.11a/n 2x2 MIMO

Antenna Dual olarization 2x2 MIMO antenna

ESD protection 15kV ESD rotection on each RF ort

15kV ESD rotection on the Ethernet ort

MiniPCI slot none

Serial port none

LEDs Power and User LED, 5 wireless LEDs

Extras Bee er; Reset switch; USB 2.0 ort; Voltage monitor; Tem erature monitor

Power options Power over Ethernet: 8..30V DC (exce t ower over datalines)

Packaged with a 24V PSU and a PoE injector

Dimensions 140x140x56mm

Weight 265g

Temperature O erational: -30C to +80C

Power consumption 5W max

RouterOS license Level3

Hardware Guide

LAN1 Port with PoE

It is com atible with assive (non-standard) Power over Ethernet. The board acce ts voltage in ut from 8 to

30 V DC. It is suggested to use higher voltages for ower over long cables because of better efficiency (less

ower is lost in the cable itself and ower su ly is more efficient).

See Connector Index for inout of the standard cable required for PoE. All cables made to EIA/TIA 568A/B

cable s ecifications will work correctly with PoE. Note that this ort su orts automatic cross/straight cable

correction (Auto MDI/X), so you can use either straight or cross-over cable for connecting to other devices.

LEDs

•Power LED is on when the board is owered. O en case door to see it.

•User LED. O en door to see it. May be rogrammed at user's o tion. It is lit by default when the

board starts u , then it is turned off when the bootloader runs kernel. These RouterOS commands

turn it on/off: :led user-led=no ; :led user-led=yes

•SXT-5D has 5 LEDs (LD1602..LD1606), which show wireless signal strength:

LD1602 - on, if wireless client is connected to AP (usually >= -89dBm)

LD1603 - on, if signal strength >= -82dBm

LD1604 - on, if signal strength >= -75dBm

LD1605 - on, if signal strength >= -68dBm

LD1606 - on, if signal strength >= -61dBm

It is ossible to disable this function (turn all these LEDs off) via software configuration.

RouterBOARD SXT Series User's Manual rev. 6

Onboard 802.11a/n 5 Hz wireless

This RouterBOARD model has a built-in 802.11a/n 5GHz wireless device based on the AR9280 Atheros

chi set. It doesn't su ort turbo mode.

There is no antenna connector, as the wireless art is directly connected to the built-in antenna.

Protocol Data rate TX Power

802.11a 6 Mbit/s 26dBm

54 Mbit/s 22dBm

802.11n

MCS0/8 20MHZ 25dBm

MCS0/8 40MHZ 25dBm

MCS7/15 20MHZ 19dBm

MCS7/15 40MHZ 18dBm

Protocol Data rate RX Sensitivity

802.11a 6 Mbit/s -96dBm

54 Mbit/s -80dBm

802.11n

MCS0/8 20MHZ -96dBm

MCS0/8 40MHZ -92dBm

MCS7/15 20MHZ -77dBm

MCS7/15 40MHZ -74dBm

Built in antenna

The SXT 5HnD has a built in dual olarization PCB ty e antenna:

Antenna

Ty e Dual olarization 5GHz antenna

Frequency range 5.17 - 5.825 GHz

Gain 16 ± 2 dBi

VSWR, max 1.7:1

3 dB Beam-Width, H-Plane, ty . 25 °

3 dB Beam-Width, E-Plane, ty . 25 °

Polarization Dual Linear (V- ol, H- ol)

Port to Port Isolation - 35 dB

For single chain o eration in V- ol, these o tions can be considered:

1. leave everything as is, it will connect to V ol devices by default if you didn't disable any chains in

RouterOS settings

2. Turn antenna 90deg and use Chain0

3. Don't turn antenna but disable Chain0-TX in RouterOS

USB port

The SXT has one USB 2.0 ort. This ort su orts RouterOS USB ower reset, a feature introduced to hel

reboot 3G modems, but will reset any device connected to the USB ort. It's available since RouterOS v4.14

/system resource usb power-reset

RouterBOARD SXT Series User's Manual rev. 6

The command disconnects ower for USB ort. However, the same ower source is used for the Wireless

ower am lifier. It means, that during USB ower reset wireless signals are transmitted with reduced ower.

It may cause small interru tion of wireless communication.

User's Guide

First use

The SXT device is assembled and ready to use:

•Plug the su lied PSU into a ower socket, and connect it to the su lied PoE injector

•Connect one end of the injector to a switch or any other device, and the other end to Ethernet cable

leading to the SXT device

•Connect to the SXT device with SSH or Winbox to configure it. See this document for details:

htt ://wiki.mikrotik.com/wiki/Manual:First_time_startu

•Configure RouterOS according to the manual:

htt ://wiki.mikrotik.com/wiki/Category:Manual

Configuration note: Wireless interface is disabled by default, you need to connect with any of the above

methods and enable and configure it. To use both chains, you need to enable HT TX/RX chains in the HT tab

in the RouterOS Wireless configuration.

rounding

It is recommend to use a FTP (foil screened twisted air) cable – in this case, one end of the cable would be

lugged into the SXT, the other end of the cable will be connected to the buildings grounding installation. If

ossible, also connect a grounding wire to the rovided grounding connection behind the SXT case door.

Powering

•Power over Ethernet (PoE) on the Ethernet ort:

8..30V DC (12..28 V suggested) non-standard PoE owering su ort. 24V PSU is su lied with the

device

RouterBOARD SXT series boards are com atible with non-standard ( assive) Power over Ethernet injectors

(exce t ower over datalines) and acce t owering over u to 100m (330 ft) long Ethernet cable connected

to the Ethernet ort (J4). The board does not work with IEEE802.3af com liant 48V ower injectors.

Mounting

With the cli ointed forward, slide the mounting bracket onto the rail on the bottom of the case, until the

cli clicks into lace. Make sure the cli is securely holding the mounting bracket in lace.

The SXT comes bundled with a hose clam - guide the clam through the o ening in the bracket and around

the ole where it will be mounted. Tighten the hose clam screw when alignment is com lete. Two screw

holes are rovided as additional security against accidental bracket movement.

The SXT must be mounted with the door ointing downwards, to avoid moisture coming into the box. The

image shows the only correct way to mount the device. Small holes are located on the bottom to

rovide ventilation and exit for condensate:

Bottom

RouterBOARD SXT Series User's Manual rev. 6

The SXT device has a sliding door, behind which the Ethernet ort, USB ort, and the reset jum ers are

located. Also the User and Power LEDs become visible. When closing the door, make sure to click the latch

into lace by a lying medium amount of force. Make sure the door is tightly closed. This door can be also

secured shut with a screw in the rovided screw hole. This is also rotection against unwanted access to

your Ethernet ort.

If you would want to mount the SXT horizontally, you need to use the second cable o ening, so that the

Ethernet cable goes straight down from that osition. By default this o ening is not accessible, you need to

use a drill or a shar knife to o en the second cable o ening. The second cable o ening could also be used

for grounding wire or USB cable.

Booting options

First, RouterBOOT loader is started. The loader may be configured to boot the system from the onboard

NAND module or from Ethernet network. See the res ective section of this manual for how to configure

booting sequence and other boot loader arameters.

To reset RouterOS, or start booting from network, use the reset button. See Button Index

Onboard NAND Storage Device

The RouterBOARD may be started from the onboard NAND storage chi . As there is no artition table on the

device, the boot loader assumes the first 4MiB form a YAFFS filesystem, and executes the file called “kernel”

stored in the root directory on that artition.

Booting from network

Network boot works similarly to PXE or EtherBoot rotocol, and allows you to boot a RouterBOARD SXT

series device from an executable image stored on a TFTP server. It uses BOOTP or DHCP (configurable in

boot loader) rotocol to get a valid IP address, and TFTP rotocol to download an executable (ELF) kernel

image combined with the initial RAM disk (inserted as an ELF section) to boot from (the TFTP server's IP

Second cable opening

RouterBOARD SXT Series User's Manual rev. 6

address and the image name must be sent by the BOOTP/DHCP server).

To boot the RouterBOARD com uter from Ethernet network you need the following:

●An ELF kernel image for the loader to boot from (you can embed the kernel arameters and initrd

image as ELF sections called kernparm and initrd res ectively)

●A TFTP server which to download the image from

●A BOOTP/DHCP server (may be installed on the same machine as the TFTP server) to give an IP

address, TFTP server address and boot image name

See the Button Index section on how to configure loader to boot from network.

Note that you must connect the RouterBOARD you want to boot, and the BOOTP/DHCP and TFTP servers to

the same broadcast domain (ie., there must not be any routers between them).

RouterBOOT

The RouterBOOT firmware (also referred as “boot loader” here) rovides minimal functionality to boot an

O erating System. RouterBOOT can be configured from the RouterOS “/system routerboard” menu. The

loader su orts booting from the onboard NAND device and from a network server (see the res ective

section for details on this rotocol).

Boot Loader Configuration

As this device doesn't have a serial ort, the Bootloader arameters may be configured through RouterOS

“/system routerboard” menu.

Boot Loader Upgrading

The boot loader is needed to initialize all the hardware and boot the system u . It's generally a good idea to

u grade the loader once a newer RouterOS version is available.

The boot loader u grading is su orted from MikroTik RouterOS. U load the FWF file to RouterOS files

menu, and run the “/system routerboard u grade” command. Usually, RouterOS releases already include the

new Bootloader files in the routerboard.n k ackage, so if you have this ackage installed, you can check if

new Bootloader is available:

[admin@SXT] > system routerboard print

routerboard: yes

model: "SXT"

serial-number: " FC20 AD5C64"

current-firmware: "2.27"

upgrade-firmware: "2.29"

[admin@SXT] >

As you see in the above example, new firmware is available. Type the following command to

upgrade it:

[admin@SXT] > system routerboard upgrade

Operating System Support

Currently tested o erating system is MikroTik RouterOS (starting from version v4.16). Downgrading the

device to older RouterOS versions can cause malfunction and License issues.

Connector Index

J4 RJ45 Fast Ethernet 100Base-TX ort LAN1 with assive PoE extension

1 Data TX+

2 Data TX-

3 Data RX+

RouterBOARD SXT Series User's Manual rev. 6

PoE ower +

Data RX-

PoE ower -

RouterBOARD SXT Series User's Manual rev. 6

Button Index

S1400 This button has three functions. Hold the button, then a ly ower. De ending on when you

release the button, it will do these things:

•release immediately (0-5 seconds) after starting the device to load backu bootloader

•release when user LED starts to flash to reset RouterOS (5-10 seconds)

•release after user LED sto s flashing to start Etherboot (Netinstall) mode

(10+ seconds)

RESET RouterOS reset jum er hole (RESET, marked with a black circle in the diagram above, below

S1400) – resets RouterOS software to defaults. Must short circuit the metallic sides of the

hole (with a screwdriver, for exam le) and boot the device. Hold screwdriver in lace until

RouterOS configuration is cleared.

Ethernet Cables

RJ45

Color Function RJ45 pin for Straight cable

(MDI, EIA/TIA568A)

RJ45 pin for Crossover cable

(MDI-X, EIA/TIA568B)

1 Green TX+ Data 1 3

2 Green/White TX- Data 2 6

3 Orange RX+ Data 3 1

4 Blue - 4 4

5 Blue/White - 5 5

6 Orange/White RX- Data 6 2

7 Brown - 7 7

8 Brown/White - 8 8

Federal Communication Commission Interference Statement

(FCC ID: TV7SXT-5D)

This equi ment has been tested and found to com ly with the limits for a Class B digital device, ursuant to

Part 15 of the FCC Rules. These limits are designed to rovide reasonable rotection against harmful

interference in a residential installation. This equi ment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a articular

installation. If this equi ment does cause harmful interference to radio or television rece tion, which can be

determined by turning the equi ment off and on, the user is encouraged to try to correct the interference by

one of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the se aration between the equi ment and receiver.

● Connect the equi ment into an outlet on a circuit different from that to which the receiver is connected.

● Consult the dealer or an ex erienced radio/TV technician for hel .

FCC Caution: Any changes or modifications not ex ressly a roved by the arty res onsible for com liance

could void the user’s authority to o erate this equi ment.

This device com lies with Part 15 of the FCC Rules. O eration is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must acce t any interference received,

including interference that may cause undesired o eration.

This device and its antenna must not be co-located or o eration in conjunction with any other antenna or

transmitter. IMPORTANT: Ex osure to Radio Frequency Radiation. 20 cm minimum distance has to be

maintained between the antenna and the occu ational user and 45 cm to general ublic. Under such

configuration, the FCC radiation ex osure limits set forth for an o ulation/uncontrolled environment can be

satisfied.

Andere Handbücher für RouterBOARD SXT 5HnD

Inhaltsverzeichnis

Andere MikroTik Drahtloser Zugangspunkt Handbücher

MikroTik

MikroTik hAP mini Bedienungsanleitung

MikroTik

MikroTik LtAP LR8 LTE kit Bedienungsanleitung

MikroTik

MikroTik LtAP LR8 LTE kit Bedienungsanleitung

MikroTik

MikroTik wAP 60G Series Bedienungsanleitung

MikroTik

MikroTik DynaDish 6 Bedienungsanleitung

MikroTik

MikroTik wsAP ac lite Bedienungsanleitung

MikroTik

MikroTik LDF 5 Bedienungsanleitung

MikroTik

MikroTik Wireless Wire Cube Bedienungsanleitung

MikroTik

MikroTik RouterBOARD wAP R Bedienungsanleitung

MikroTik

MikroTik PWR-LINE AP Bedienungsanleitung

MikroTik

MikroTik mANTBox 2 12s Bedienungsanleitung

MikroTik

MikroTik Cube 60G Series Bedienungsanleitung

MikroTik

MikroTik Audience LTE6 kit Bedienungsanleitung

MikroTik

MikroTik RouterBoard 951 Ui-2HnD Bedienungsanleitung

MikroTik

MikroTik LHG Series Bedienungsanleitung

MikroTik

MikroTik hAP ac3 LTE6 kit Bedienungsanleitung

MikroTik

MikroTik Cube 60G Series Bedienungsanleitung

MikroTik

MikroTik Chateau LTE6-US Bedienungsanleitung

MikroTik

MikroTik RouterBOARD Groove 5Hn Bedienungsanleitung

MikroTik

MikroTik cAP ax Bedienungsanleitung

MikroTik

MikroTik mAP 2nD Bedienungsanleitung

MikroTik

MikroTik NetMetal ac2 Series Bedienungsanleitung

MikroTik

MikroTik hAP ac2 Bedienungsanleitung

MikroTik

MikroTik wAP LR2 kit Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung