MikroTik Wireless Wire Cube Bedienungsanleitung
Wireless Wire Cube
Wireless Wire Cube (CubeG-5ac60adpair)
Safety Warnings
Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing
accidents.
Ultimate disposal of this product should be handled according to all national laws and regulations.
The Installation of the equipment must comply with local and national electrical codes.
This unit is intended to be installed in the rackmount. Please read the mounting instructions carefully before beginning installation. Failure to use the
correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.
This product is intended to be installed indoors. Keep this product away from water, fire, humidity or hot environments.
Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.
Read the installation instructions before connecting the system to the power source.
We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your
own risk!
In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.
It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling
requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.
This is a class A device. In a domestic environment, this product might cause radio interference in which case the user might be required to take adequate
measures.
Exposure to Radio Frequency Radiation:This MikroTik equipment complies with the FCC, IC, and European Union radiation exposure limits set forth for an
uncontrolled environment.This MikroTik device should be installed and operated no closer than 21 centimeters from your body, occupational user, or the
general public.
Quickstart
Connect the device to the included PoE injector with Ethernet cable;
Connect the PoE injector into the PC or to the network switch;
Connect the power adapter to the PoE injector;
Download WinBox configuration tool ;https://mt.lv/winbox
Open WinBox and connect to the device;
Default IP: 192.168.88.2/192.168.88.3, user name:
admin
, please find the password on the sticker;
Download the latest RouterOS software from ;https://mikrotik.com/download
Choose ARM packages, and save them to your PC;
Open WinBox and upload downloaded packages, drag and drop into any windows;
Restart the device;
Connect again and select your Region in the Wireless menu, W60G tab, and in menu set your Country, to apply country regulation
QuickSet
settings.
If device RX blocking condition has happened device will restore its signal after a few seconds.
It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling
requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.
Note. The information contained here is subject to change. Please visit the product page on www.mikrotik.com for the most up to date version of
this document.
1.
2.
3.
4.
5.
6.
1.
2.
3.
MikroTik mobile app
Use the MikroTik smartphone app to configure your router in the field, or to apply the most basic initial settings for your MikroTik home access point.
Scan QR code and choose your preferred OS.
Install and open application.
By default, the IP address and user name will be already entered.
Click Connect to establish a connection to your device through a wireless network.
Choose Quick setup and application will guide you through all basic configuration settings in a couple of easy steps.
An advanced menu is available to fully configure all necessary settings.
Configuration
Once logged in, we recommend clicking the "Check for updates" button in the QuickSet menu, as updating your RouterOS software to the latest version
ensures the best performance and stability. For wireless models, please make sure you have selected the country where the device will be used, to
conform with local regulations.
RouterOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself accustomed to
the possibilities: . In case IP connection is not available, the Winbox tool ( ) can be used to connect to the MAC address https://mt.lv/help https://mt.lv/winbox
of the device from the LAN side (all access is blocked from the Internet port by default).
For recovery purposes, it is possible to boot the device from the network (see ).Reset button
If the device loses connection, wait for few seconds and then the device will recover connection automatically.
Assembly and mounting
The device can be mounted on the vertical or horizontal pole as shown in pictures A and B. Please note that a device needs to be mounted with the bottom
latch facing down. The maximum pole diameter is 51 mm.
Choose your desired position, the device will require precise adjustment for best performance.
Attach provided mount to the back of the device with provided screws using a ph0 screwdriver.
Mount on pole with U bolt bracket using 8 mm ratchet.
Place a bolt in one of the three positions, they will allow for fine adjustment, when placed in the middle you can adjust in a 23-degree range if an
adjustment needs to go further replace the screw in a different position.
Mounting and configuration of this device should be done by a certified person.
Alternatively, the device can be mounted on one of the three mounting slots on the backside of the device.
You can use a metal ring for example.
Use a Phillips screwdriver to loosen the metal ring.
Slide one end of it through the most convenient of the three mounting slots.
Position the device on the pole where it will be mounted.
Slide the loose end of the mounting ring back to its closing latch and use the screwdriver to tighten it.
The IP rating scale for this device is IP54. When mounting outdoors, please ensure that any cable openings are directed downwards. We
recommend using the POE injector and proper grounding with Cat6 shielded cable. When using and installing this device please pay attention
to Maximum Permissible Exposure (MPE) safety distance with a minimum of 20 cm between the radiator and your body.
1.
2.
3.
As an additional option, you can use "quickMOUNT-X" – mounting bracket for an easy adjustment that can be obtained separately. Product web page: https
://mikrotik.com/product/qm_x
Specially designed enables vertical and horizontal adjustment on the pole.
Grounding
The device includes a grounding connection (marked ) which you should connect to the grounding installation of the tower or building where the device will
be used. This is to substantially reduce the risk of ESD and lightning damage.
Powering
The Cube Lite60 accepts DC power from Passive PoE injectors (one power supply and PoE injector are included) accepts 12-28 V DC consuming at
maximum load 4 W.
Connecting to a PoE Adapter:
Connect the Ethernet cable from the device to the PoE+DATA port of the PoE adapter.
Connect an Ethernet cable from your local network (LAN) to the PoE adapter.
Connect the power cord to the adapter, and then plug the power cord into a power outlet.
Extension Slots and Ports
10/100 Ethernet port.
Integrated 5 GHz 802.11a/n/ac interface with built-in antenna.
WiGig chipset QCA6335.
Reset button
The routerBOOT reset button has the following functions. Press the button and apply the power, then:
Release the button when green LED starts flashing, to reset RouterOS configuration to defaults.
Release the button when the LED turns solid green to clear all configuration and defaults.
Release the button after LED is no longer lit (~20 seconds) to cause the device to look for Netinstall servers (required for reinstalling RouterOS
over the network).
Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device.
Useful for RouterBOOT debugging and recovery.
Accessories
It's recommended to secure Ethernet cable to the pole using zip ties. With the distance from the device approximately 30 cm.
Package includes the following accessories that come with the device:
EU/US Switching Power Supply 24V DC , 0.8 A, 9 W, Level VI, cable:1.5 m.
POE Injector with shielded ethernet cable/connector (RBPOE).
Cube mount.
K-70 Fastening set for Cube mount.
Operating system support
The device supports RouterOS software version The specific factory-installed version number is indicated in the RouterOS menu /system
v6.47.2.
resource. Other operating systems have not been tested.
Notes
Federal Communication Commission Interference Statement
Model FCCID
CubeG-5ac60adpair TV7CB5A60
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a commercial installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate thisFCC Caution:
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device is not to be operated on aircraft except for the conditions listed on FCC CFR §15.255 (b)
IMPORTANT NOTE. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 21cm between the radiator & your body.
All cables used to connect peripherals must be shielded and grounded. Operation with cables connected to peripherals that are not shielded and grounded
may result in interference to radio and television reception.
Innovation, Science and Economic Development Canada
This device meets the Maximum TX power limit per ETSI regulations. The frequency and the maximum transmitted power in the EU are listed
below: 57-66GHz: 34.92 dBm. An Operational mode in the 60 GHz band: 58.32 GHz, 60.48 GHz, 62.64 GHz. This device is certified for outdoor
use in Point to Multipoint applications. In the following countries this device cannot be used in Fixed Point-to-Point applications:
Model IC
CubeG-5ac60adpair 7442A-CB5A60
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) L’appareil ne doit pas produire
de brouillage; 2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
This ClassAdigital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.
CAN ICES-003 (A) / NMB-003 (A)
This device is not to be operated on aircraft except for the conditions listed on ISED RSS-210 Annex J.1.
Cet appareil ne doit pas être utilisé sur un avion, sauf dans les conditions énumérées ISED RSS-210 Annex J.1.
IMPORTANT NOTE. IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance 21cm between the radiator & your body.
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé
et utilisé avec un minimum de 21cm de distance entre la source de rayonnement et votre corps.
UKCA marking
Eurasian Conformity Mark
Частотный каналы Мощность передатчика
5650-5850 МГц ≤10 Вт
*Доступные частотные каналы могут различаться в зависимости от модели продукта и сертификации.
Информация о дате изготовления устройства указана в конце серийного номера на его наклейке через дробь. Первая цифра означает номер
года (последняя цифра года), две последующие означают номер недели.
Изготовитель: Mikrotikls SIA, Aizkraukles iela 23, Riga, LV-1006, Латвия, [email protected]. Сделано в Китае, Латвии или Литве. Cм. на
упаковке.
Для получения подробных сведений о гарантийном обслуживании обратитесь к продавцу. Информация об импортерах продукции MikroTik в
Российскую Федерацию: https://mikrotik.com/buy/europe/russia
Продукты MikroTik, которые поставляются в Евразийский таможенный союз, оцениваются с учетом соответствующих требований и помечены
знаком EAC, как показано ниже:
Norma Oficial Mexicana
Rango de frecuencia (potencia de salida máxima): Los canales de frecuencia disponibles pueden variar según el modelo y la 5725-5850 MHz (30 dBm).
certificación del producto.
EFICIENCIA ENERGETICA CUMPLE CON LA NOM-029-ENER-2017.
La operacion de este equipo esta sujeta a las siguientes dos condiciones:
Es posible que este equipo o dispositivo no cause interferencia perjudicial y.
Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacion no deseada.
Fabricante: Mikrotikls SIA, Brivibas gatve 214i, Riga, LV-1039, Latvia.
País De Origen: Letonia; Lituania; China (Republica Popular); Estados Unidos De America; Mexico.
Por favor contacte a su distribuidor local para preguntas regionales específicas. La lista de importadores se puede encontrar en nuestra página de inicio –
https://mikrotik.com/buy/latinamerica/mexico.
The National Commission for the State Regulation of Communications and
Informatization by Ukraine
Виробник: Mikrotikls SIA, Brivibas gatve 214i Рига, Латвія, LV1039.
Робоча частота (Максимальна вихідна потужність): 5470-5725 МГц (27 дБм).
CE Declaration of Conformity
Manufacturer: Mikrotikls SIA, Brivibas gatve 214i Riga, Latvia, LV1039.
Hereby, Mikrotīkls SIA declares that the radio equipment type CubeG-5ac60adpair is in compliance with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following internet address:https://mikrotik.com/products
WiGig
Operational channels /Maximum output power
Betriebskanäle /maximale Ausgangsleistung
Canaux opérationnels /puissance de sortie maximale
Canali operativi /massima potenza di uscita
Canales operacionales /potencia de salida máxima
Операционные каналы /максимальная выходная мощность
58.32 GHz / <40 dBm
60.48 GHz /<40 dBm
62.64 GHz /<40 dBm
WLAN
Operating Frequency / Maximum output power
Betriebsfrequenz / maximale Ausgangsleistung
Fréquence de fonctionnement / puissance de sortie maximale 5470-5725 MHz / 27 dBm
Справжнім Mikrotikls SIA заявляє, що маршрутизатор відповідає основним вимогам та іншим відповідним положенням директиви 2014
/53/EC, а також суттєвим вимогам Технічного регламенту радіообладнання, затвердженого постановою Кабінету Міністрів України від
24 травня 2017 року № 355.
Для експлуатації в Україні необхідно отримати дозвіл на експлуатацію у порядку, затвердженому рішенням НКРЗІ від 01.11.2012 № 559,
зареєстрованому в Міністерстві юстиції України 03.01.2013 за № 57/22589.
Note. Information contained here is subject to change. Please visit the product page on
www.mikrotik.com
for the most up to date version of this
document.
Frequenza operativa / massima potenza di uscita
Frecuencia de funcionamiento / potencia de salida máxima
Рабочая частота / максимальная выходная мощность
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere MikroTik Drahtloser Zugangspunkt Handbücher
MikroTik
MikroTik RB931-2nD Bedienungsanleitung
MikroTik
MikroTik Chateau 5G Bedienungsanleitung
MikroTik
MikroTik hAP ac3 LTE6 kit Bedienungsanleitung
MikroTik
MikroTik RouterBOARD wAP R Bedienungsanleitung
MikroTik
MikroTik RBLHGGR&R11e-LTE6 Bedienungsanleitung
MikroTik
MikroTik RBcAPGi-5acD2nD-XL Bedienungsanleitung
MikroTik
MikroTik LHG XL 52 ac Bedienungsanleitung
MikroTik
MikroTik LtAP LR8 LTE kit Bedienungsanleitung
MikroTik
MikroTik LtAP RB912R-2nD-LTm&R11e-LTE-US Bedienungsanleitung
MikroTik
MikroTik LtAP LR8 LTE kit Bedienungsanleitung
MikroTik
MikroTik BaseBox 2 Bedienungsanleitung
MikroTik
MikroTik SXTG-5HPacD-HG Bedienungsanleitung
MikroTik
MikroTik RBcAPGi-5acD2nD-XL Bedienungsanleitung
MikroTik
MikroTik wsAP ac lite Bedienungsanleitung
MikroTik
MikroTik SXTG-5HPacD Bedienungsanleitung
MikroTik
MikroTik RB912R-2nD-LTm Bedienungsanleitung
MikroTik
MikroTik hAP ac2 Bedienungsanleitung
MikroTik
MikroTik RouterBOARD Groove 52HPn Bedienungsanleitung
MikroTik
MikroTik LHG 60G Bedienungsanleitung
MikroTik
MikroTik wAP ac Series Bedienungsanleitung
Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation NSM2 Bedienungsanleitung
Cisco
Cisco Aironet 1550 Series Bedienungsanleitung
Aruba
Aruba IAP-335 Bedienungsanleitung
Advantek Networks
Advantek Networks AWN-AP-54MR Bedienungsanleitung
IP-COM
IP-COM AP355 Bedienungsanleitung
Buffalo
Buffalo AirStation WLA-L11G Bedienungsanleitung
EnGenius
EnGenius EnStationACv2 Bedienungsanleitung
D-Link
D-Link DAP-3662 Bedienungsanleitung
xG Technology
xG Technology xMax CN1300 Bedienungsanleitung
Widelink
Widelink ezWave WAP-1100 Series Bedienungsanleitung
Edimax
Edimax CAP1200 Bedienungsanleitung
