Milwaukee MI 406 Bedienungsanleitung

USER MANUAL

MI 406

Free Chlorine Meter

Dear Customer,

Thank you for choosing a Martini product.

This manual will provide you with the

necessary information for the correct use of

the instrument.

Please read it carefully before using the

meter. This instrument is in compliance with

directives.

SPECIFICATIONS:

Range 0.00 to 5.00 mg/L Cl2

Resolution 0.01 mg/L (0.00-3.50 mg/L);

0.10 mg/L (above 3.50 mg/L)

Precision ±0.04 mg/L @ 1.50 mg/L

Light Source Tungsten lamp

Light Detector Silicon Photocell and

525 nm narrow band interference filter

Method Adaption of the USEPA method 330.5 and Standard Method 4500-Cl G.

Environment 0 to 50°C (32 to 122°F);

100% RH max.

Battery Type 1 x 9 volt

Auto-Shut off After 10' of non-use

Dimensions 192 x 104 x 52 mm

(7.5 x 4.1 x 2”)

Weight 380 g

MEASUREMENT PROCEDURE:

1• Turn the meter on by pressing

ON/OFF.

2• When the LCD displays “- - -”, the

meter is ready.

3• Fill the cuvet with 10

mL of sample, up to the

mark, and replace the

cap.

4• Place the cuvet into the

holder and ensure that

the notch on the cap is

positioned securely into

the groove.

5• Press ZERO and “SIP”

will blink on the display.

6• After a few seconds the

display will show “-0.0-

”. The meter is now

zeroed and ready for

measurement.

7• Remove the cuvet. Open it.

8• Add 3 drops of DPD 1 indicator and

3 drops of DPD 2 buffer to an empty

cuvet. Immediately add 10 mL of

unreacted sample. Replace the cap

and shake gently.

9• Replace the cuvet into the holder

and ensure that the notch on the cap

is positioned securely into the

groove.

10•Press READ and “SIP”

will blink during

measurement.

11•The instrument directly

displays the

concentration in mg/L of free

chlorine.

Interferences

• Positive error:

- Bromine

- Chlorine Dioxide

- Iodine

- Oxidized Manganese and

Chromium

- Ozone

• Alkalinity above 250 mg/L CaCO3 or

acidity above 150 mg/L CaCO3 will

not reliably develop the full amount

of color or it may rapidly fade.

To resolve this, neutralize the

sample with diluted HCl or NaOH.

• In case of water with hardness

greater than 500 mg/L CaCO3,

shake the sample for approximately

2’ after adding the powder reagent.

GUIDE TO DISPLAY CODES:

This prompt appears for 1 second each

time the instrument is turned on.

The dashes “- - -”

indicates that the

meter is in a ready

state and zeroing can

be performed.

Sampling In Progress.

Flashing “SIP” prompt

appears each time the

meter is performing a

measurement.

“-0.0-”, the meter is in

a zeroed state and

measurement can be

performed.

The blinking "BAT"

indicates that the

battery voltage is

getting low and the

battery needs to be

replaced.

“-bA-”, the battery is

dead and must be

replaced. Once this

indication is displayed,

the meter will lock up.

Change the battery

and restart the meter.

“Conf”, the meter has

lost its configuration. Contact your

dealer or the nearest Martini Customer

Service Center.

ERROR MESSAGES

On zero reading

• Blinking “-0.0-” indicates that the

zeroing procedure failed due to a low

signalto-noise ratio.

In this case

press ZERO again.

• “no L”, the

instrument can not

adjust the light

level. Please check

that the sample

does not contain

any debris.

• “L Lo”, there is

not enough light to

perform a

measurement.

Please check the

preparation of the

zero cuvet.

• “L Hi”, there is too

much light to

perform a

measurement.

Please check the preparation of the zero

cuvet.

On sample reading

• “-SA-”, there is too

much light for the

sample

measurement.

Please check if the

right sample cuvet is

inserted.

• “Inv”, the sample

and the zero cuvet

are inverted.

• “ZErO”, a zero

reading was not

taken. Follow the instruction in the

measurement procedure for zeroing the

meter.

• Under range. A blinking “0.00”

indicates that the sample absorbs less

light than the zero

reference.

Check the procedure

and make sure you

use the same cuvet

for reference (zero)

and measurement.

• A flashing value of

the maximum

concentration

indicates an over

range condition.

The concentration of

the sample is beyond

the programmed range: dilute the

sample and re-run the test.

BATTERY REPLACEMENT

Battery replacement must only take

place in a non-hazardous environment.

Simply rotate the battery cover on the

back of the meter.

Detach the

battery from

the terminals

and attach a

fresh 9V

battery while

paying

attention to

the correct

polarity.

Insert the battery and replace the cover.

ACCESSORIES:

MI506-100 Free Chlorine (100 tests)

MI0001 Glass cuvets (2 pcs)

MI0002 Caps for cuvets (2 pcs)

MI0003 Stoppers for cuvets (2 pcs)

MI0004 Tissue for wipping cuvets

(4 pcs)

MI0005 9V battery (1 pc)

WARRANTY

This instrument is warranted against defects

in materials and manufacturing for a period of

two years from the date of purchase.

If during this period the repair or replacement

of parts is required, where the damage is not

due to negligence or erroneous operation by

the user, please

return the meter to either distributor or our

office in the original packing and the repair

will be free of charge.

Damages due to accidents, misuse,

tampering or lack of prescribed maintenance

are not covered.

Andere Milwaukee Messgerät Handbücher

Milwaukee

Milwaukee C 12 IC AVD Bedienungsanleitung

Milwaukee

Milwaukee EC40 Bedienungsanleitung

Milwaukee

Milwaukee MI805 Bedienungsanleitung

Milwaukee

Milwaukee 3631-20 Bedienungsanleitung

Milwaukee

Milwaukee PST MW12 Bedienungsanleitung

Milwaukee

Milwaukee 2205-40 Bedienungsanleitung

Milwaukee

Milwaukee MI412 Bedienungsanleitung

Milwaukee

Milwaukee MW500 Bedienungsanleitung

Milwaukee

Milwaukee MI 413 Bedienungsanleitung

Milwaukee

Milwaukee LDM 45 Bedienungsanleitung

Milwaukee

Milwaukee REDLITHIUM Bedienungsanleitung

Milwaukee

Milwaukee HEAVY DUTY 7,5 m LED Tape Measure Bedienungsanleitung

Milwaukee

Milwaukee Smart Monitoring System SMS110 Bedienungsanleitung

Milwaukee

Milwaukee MW14 Bedienungsanleitung

Milwaukee

Milwaukee Mi451 Bedienungsanleitung

Milwaukee

Milwaukee PH55 Bedienungsanleitung

Milwaukee

Milwaukee MI415 Bedienungsanleitung

Milwaukee

Milwaukee MI406 Bedienungsanleitung

Milwaukee

Milwaukee MW306 MAX Bedienungsanleitung

Milwaukee

Milwaukee MW 14 Bedienungsanleitung

Milwaukee

Milwaukee 48-22-9801 Bedienungsanleitung

Milwaukee

Milwaukee MW802 Bedienungsanleitung

Milwaukee

Milwaukee MW150 Bedienungsanleitung

Milwaukee

Milwaukee MC125 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung