Molex RHT-4754 Bedienungsanleitung

RHT-4754 Hand Crimp Tool

Doc No. 64003-7200 Release Date: 08-02-06 UNCONTROLLED

COPY Page 1 of 7

Revision: A Revision Date: 08-02-06

Hand Crimp Tool

Operating Instruction and Specifications Sheet

Part No. 64003-7200

Eng. No. RHT-4754

(Replaces 19284-0024)

FEATURES

A full cycle ratcheting hand tool ensures complete crimps

Long handles for comfortable crimping with reduced crimping force

A precision user-friendly terminal locator wire stop holds terminals in the proper crimping

position

Insulation crimp adjustment allows a precise insulation crimp.

2-nested tool eliminates the need for additional tools

SCOPE

VibrakrimpFemale Non-Insulated Std. and Piggyback Quick Disconnects, 14–22 AWG.

Testing

Mechanical

The tensile test or pull test is a means of evaluating the mechanical properties of the

crimped connections. The following charts show the UL specifications for various wire

sizes. The tensile strength is shown in pounds and indicates the minimum acceptable force

to break or separate the terminal from the conductor.

Wire Size (AWG)

*UL - 310

*UL –310 –Quick Disconnects

The following is a partial list of the product part numbers and their specifications that this tool

is designed to run. We will be adding to this list and an up to date copy is available on

www.molex.com.

Wire Size: 18-22 AWG 0.80 –0.35mm2

Terminal

No.

Terminal

Eng No. (REF)

Wire Strip Length

Insul. Dia. Max.

In.

190180001

AA-4173

.220

5.56

.130

3.18

190180002

AA-4173-032

.220

5.56

.130

3.18

190180005

AA-4176

.220

5.56

.130

3.18

190180007

AA-4180

.220

5.56

.130

3.18

190430002

PBT-4A

.220

5.56

.180

4.45

Wire Size: 14-16 AWG 2.00 –1.30mm2

Terminal

No.

Terminal

Eng No. (REF)

Wire Strip Length

Insul. Dia. Max.

In.

190180011

BB-4174

.220

5.56

.130

3.18

190180014

BB-4177

.220

5.56

.130

3.18

190180016

BB-4181

.220

5.56

.130

3.18

190180017

BB-4181-032

.220

5.56

.130

3.18

RHT-4754 Hand Crimp Tool

Doc No. 64003-7200 Release Date: 08-02-06 UNCONTROLLED

COPY Page 2 of 7

Revision: A Revision Date: 08-02-06

Figure 3

2ND TAB

LOCATOR

WIRE

TERMINA

BARREL

INSULATIO

PUNCH

CONDUCTOR

ANVIL

TERMINA

LOCATO

CONDUCTO

PUNCH

INSULATION

ANVIL

1ST TAB

LOCATOR

Figure 2

TERMINAL

WIRE

OPERATION

Open the tool by first closing the jaws sufficiently for the

ratchet mechanism to release.

Crimping Terminals

1. There are 2 Tab Locator Blades supplied with the

tool. One is for .187 and .250 Tabs; the other is for

.205 Tabs and .110 Tabs. Make sure the proper

blade is installed on the top of the locator and the

other is stored on the bottom of the locator.

2. Push the terminal onto the tab locator all the way to

the stop in the nest. The barrel of the terminal should be up. See Figure 1.

3. Partially close the tool to hold the terminal in place. See Figure 2.

4. Insert the properly stripped wire into the terminal barrel. See Figure 2 and 3. Cycle the

tool.

Note: The tamper proof ratchet action will not release the tool until it has been fully

closed.

5. Remove the crimp and inspect for proper crimp location, and check for insulation closure.

Molex offers a Crimp Inspection Handbook for closed barrel industrial product. See our

website or contact your sales engineer.

6. If the insulation part of the crimp needs to be adjusted, first loosen the M4 screw on the

bottom tool jaw, then insert a 3/32 hex wrench (supplied) into the bottom of the lower die.

See Figure 4. A clockwise (CW) rotation decreases insulation crimp while a counter-

clockwise (CCW) rotation increases insulation crimp. After adjusting retighten the M4

screw.

LOCATOR

JAWS

OPEN

TAB

LOCATOR

Figure 1

TERMINA

RHT-4754 Hand Crimp Tool

Doc No. 64003-7200 Release Date: 08-02-06 UNCONTROLLED

COPY Page 3 of 7

Revision: A Revision Date: 08-02-06

Maintenance

It is recommended that each operator of the tool be made aware of, and responsible for, the

following maintenance steps:

1. Remove dust, moisture and other contaminants with a clean brush, or soft, lint-free cloth.

2. Do not use any abrasive materials

that could damage the tool.

3. Make certain all pin, pivot points

and bearing surfaces are protected

with a thin coat of high quality

machine oil. Do not oil excessively.

The 64003-7200 (RHT-4754) was

engineered for durability, but like

any fine piece of equipment it needs

cleaning and lubrication for a

maximum service life of trouble-free

crimping. A light oil such as 30

weight automotive oil used at the oil

points shown in Figure 4, every

5,000 crimps or 3 months will significantly enhance the tool life and ensure a stable

calibration.

4. When tool is not in use, keep the handles closed to prevent objects from becoming lodged

in the crimping dies, and store the tool in a clean, dry area.

Miscrimps or Jams

Should this tool ever become stuck or jammed in a partially closed position, Do Not force the

handles open or closed. The tool will open easily by pressing the ratchet release lever. See

Figure 5.

How To Adjust Tool Preload (See

Figure 5)

Over the life of the tool, it may be necessary

to adjust tool handle preload force. Listed

below are the steps required to adjust the

crimping force of the hand tool to obtain

proper crimp conditions:

1. Remove the screw and plastic cover

washer. Note the setting wheel position.

2. Lift the setting wheel off the axle. Turn

the eccentric axle with a screwdriver.

3. Turning the eccentric axle counter-

clockwise will increase handle force.

4. Replace the setting wheel to the axle, aligning the nearest notch in the setting wheel to the

dowel pin.

LUBRICATION

POINTS

(BOTH SIDES)

LIGHT OIL

(EVERY 3 MONTHS

OR 5,000 CRIMPS)

Figure 4

LOOSEN

SCREW

3/32” HEX

WRENCH

Figure 5

1.00

PRELOAD

TEST

POINT

PRELOAD

TEST

POINT

PRELOAD

ADJUSTMENT

LOCKING

SCREW

RATCHET

RELEASE

LEVER

PUSH UP

RHT-4754 Hand Crimp Tool

Doc No. 64003-7200 Release Date: 08-02-06 UNCONTROLLED

COPY Page 4 of 7

Revision: A Revision Date: 08-02-06

5. Replace the plastic cover washer and screw.

6. Check the crimp specifications after tool crimp force is adjusted.

RHT-4754 Hand Crimp Tool

Doc No. 64003-7200 Release Date: 08-02-06 UNCONTROLLED

COPY Page 5 of 7

Revision: A Revision Date: 08-02-06

“ X ”

NOT POSSIBLE TO PIN GAUGE,

MEASURE A

CRIMPED UNINSULATED TERMINAL OR

SLUG*

*SOLDER, LEAD OR

SIMILAR SOFT

METAL

Tool Calibration

A Certificate of Calibration (See Last Page) was supplied with the tool. To recalibrate this

Tool, a soft metal slug or solder should be crimped in the conductor nest and the “X”

Dimension measured in each conductor nest and compared to this chart. The tool should be

lubricated prior to recalibration to ensure consistent measurements. Handle preload is

factory set to 25-45 LBS. See How to Adjust Tool Preload (See Figure 7) to recalibrate.

Nest Color Code

Wire Range

“X” Dimension

Conductor Crimp

Awg

mm²

Mean

No Go

Red

22 - 18

0.35 - 0.80

.052

.049

.060

Blue

16 - 14

1.30 - 2.00

.061

.058

.069

CAUTION: Repetitive use of this tool should be avoided.

Warranty

This tool is for electrical terminal crimping purposes only. This tool is made of the best quality

materials. All vital components are long-life tested. All tools are warranted to be free of

manufacturing defects for a period of 30 days. Should such a defect occur, we will repair or

exchange the tool free of charge. This repair or exchange will not be applicable to altered,

misused or damaged tools. This tool is designed for hand use only. Any clamping, fixturing,

or use of handle extensions voids this warranty.

Hand held crimping tools are intended for low volume, prototyping, or repair requirements

only.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals,

applicators and tooling.

RHT-4754 Hand Crimp Tool

Doc No. 64003-7200 Release Date: 08-02-06 UNCONTROLLED

COPY Page 6 of 7

Revision: A Revision Date: 08-02-06

Figure 6

M4 X 25 LG

PAN HEAD

SCREW

FOR SPRING

ACCESS

SWING

OPEN COVER

SCREW AND

PLASTIC

COVER FOR

HANDTOOL

PRELOAD

ADJUSTMENT

RATCHET

RELEASE

LEVER

M4 X 12LG

PAN HEAD

SCREW

M4 LOCKNUT W/

HEX NYLON

INSERT

M4 FLAT

WASHER

REPAIR KIT. ALL PARTS

REQUIRED FOR

REPAIR. (ONLY MAIN SPRING

SHOWN)

(2)

PARTS LIST

Item

Order No

Description

Quantity

64003-7200

Hand Crimp Tool

(Fig. 6)

64000-0076

Repair Kit (Springs, Pins and E-Rings)

63810-0000

Handle

64003-1175

Locator Assembly

64003-7270

Tooling Kit

Tooling Kit Only

64003-7202

Conductor Punch

64003-7201

Conductor Anvil

64003-7204

Insulation Punch

64003-7203

Insulation Anvil

N/A

4 mm Dia. by 5.0 mm Lg.Roll Pins

2**

N/A

#10-32 by 5/16” Lg. Cup Pt. Set Screw

1**

** The following purchased parts are available from an Industrial supply company such as MSC

(1-800-645-7270).

RHT-4754 Hand Crimp Tool

Doc No. 64003-7200 Release Date: 08-02-06 UNCONTROLLED

COPY Page 7 of 7

Revision: A Revision Date: 08-02-06

Certificate of Calibration

Tool Order Number __________________

Tool Eng. Number ___________________

Tool Revision ___________________

Serial Number ___________________

Date of Manufacture__________________

Handle Load Range at 1 inch from the Tips =______________

Actual =_____________

Pin Gauge of Conductor Nest/Nests or Slug height if the nest is the “F” Crimp style.

Range Conductor Nest # 1 = ____________-- Actual = ______________

Range Conductor Nest # 2 = ____________-- Actual = ______________

Technician______________

Date of Calibration ______________

Calibration should be done every 5,000 cycles or 3 months.

Tools should be lubricated during this operation.

Americas Headquarters

Lisle, Illinois 60532 U.S.A.

1-800-78MOLEX

amerinf[email protected]

Far East North Headquarters

Yamato, Kanagawa, Japan

81-462-65-2324

[email protected]

Far East South Headquarters

Jurong, Singapore

65-6-268-6868

fesinfo@molex.com

European Headquarters

Munich, Germany

49-89-413092-0

[email protected]

Corporate Headquarters

2222 Wellington Ct.

Lisle, IL 60532 U.S.A.

630-969-4550

Fax: 630-969-1352

Visit our Web site at http://www.molex.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere molex Crimpwerkzeuge Handbücher

molex

molex 63811-8200 Bedienungsanleitung

molex

molex 63827-6900 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63819-2900 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63825-9400 Benutzerhandbuch

molex

molex CR5905 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex RHT-4753 Bedienungsanleitung

molex

molex 63811-8700 Bedienungsanleitung

molex

molex 63827-1600 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63828-0200 Bedienungsanleitung

molex

molex 63825-6670 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63825-7570 Bedienungsanleitung

molex

molex 63811-7200 Bedienungsanleitung

molex

molex 63828-0600 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63811-6800 Bedienungsanleitung

molex

molex 63827-8770 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken

Panduit

Panduit CT-1000 Administratorhandbuch

JST

JST CS 10 Bedienungsanleitung

TE Connectivity

TE Connectivity 2063528-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 69156-1 Bedienungsanleitung

CRH

CRH CRL CBLHCT1 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFM Bedienungsanleitung

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Bedienungsanleitung

Danfoss

Danfoss ET4350 Bedienungsanleitung

Milwaukee

Milwaukee M18 Bedienungsanleitung

HOGERT

HOGERT HT1P169 Bedienungsanleitung

Textron

Textron ESG105L Bedienungsanleitung

Tyco Electronics

Tyco Electronics 90035-3 Bedienungsanleitung

Emerson

Emerson Klauke ES 20RMCCFB Bedienungsanleitung

Continental Refrigerator

Continental Refrigerator PC150HD Bedienungsanleitung

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Bedienungsanleitung

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFB Bedienungsanleitung

TE Connectivity

TE Connectivity 539 726-2 Bedienungsanleitung

molex RHT-4754 Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken