Monte Carlo Fan Company Essex 5ESR54 D Series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Total fan weight with light

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as yourproof of purchase

To register your fixture, please visit our website www.montecarlofans.com

5ESR54XXD Series Fan

UL Model NO. : 5ESR54XXD

10.2 kgs

22.44 lbs

Cautions and Warnings

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-1999), including

ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet

box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed carefully up into the outlet

box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power

from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the

service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the ﬂoor to the trailing

edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of 15.9 kg (35 lbs) or less” And

Use Mounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove Knockouts In The Outlet

Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the building structure (or the ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object

between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of ﬁre or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of ﬁre or electric shock, this fan should only be used with fan speed control part no. UC7067RY manufactured by Rhine Electronic

Co., Ltd.

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any other solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment manufacturer’s

guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

CAUTION: The light source is designed for this speciﬁc application and can overheat if serviced by untrained personnel. If any servicing is required, the product

should be returned to an authorized service facility for examination or repair.

All set screws must be checked and tightened where necessary before installation.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

1 2 3

4 5 6

OFF

Before you begin installing the fan, Switch

power off at Service panel and lock

service disconnecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be locked,

securely fasten a warning device, such

as a tag, to the service panel.

Before installing this fan make sure the

outlet box is properly installed to the

house structure. To reduce the risk of

ﬁre, electric shock, or personal injury,

mount to outlet box or supporting system

acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan

support and use only the screws provided

with the outlet box (must support 35

lbs). Before attaching fan to outlet box,

ensure the outlet box is securely fastened

by at least two points to a structural

ceiling member ( a loose box will cause

the fan to wobble). Remove the two outlet

box screws provided with the box,

aligning the holes of the mounting

bracket with the holes of the outlet box.

Reinstall the 2 outlet box screws

securely.

Partially loosen downrod set screws from

yoke at top of motor assembly.

Remove preassembled cross pin and

keeper pin from downrod.

Place downrod over canopy, hub and

yoke cover. Thread lead wires and safety

cable from motor assembly through

downrod.

Slip downrod into motor housing yoke,

aligning holes and install cross pin and

keeper pin.

Insert cross pin through yoke and downrod

until point appears on the other side, and

insert keeper pin on cross pin.

Pull the downrod up tight against the

cross pin, and then evenly tighten the

downrod set screws on motor housing

yoke.

Place yoke cover on top housing of fan.

Warning: Cross pin and keeper pin must

be installed securely, failure to install them

will result in serious injury.

Mounting bracket

Downrod

Cross pin

Keeper pin

Yoke Downrod

Canopy

Yoke cover

Hub

7 8 9

10 11 12

Install ball end of downrod into mounting

bracket opening. Align (engage) slot on

ball with tab on mounting bracket.

Warning: Failure to align slot on ball with

tab may result in serious injury.

For Canadian installation and for USA fan

and light kit combinations over 35 lbs, in

both ﬂush and downrod modes the safety

cable must be installed into the house

structure beams using 3” lag screws,

washers and lock washers provided.

Make sure that when the safety cable is

fully extended the lead wires are longer

than the cable and no stress is placed on

the lead wires.

Note: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box.

Set dip switches on the Remote

Transmitter and Remote Receiver to the

same settings. This must be done so the

units will communicate properly. If you

have other fans you can set to control

from one Transmitter by setting

receivers the same as the Transmitter. If

you have more than one fan with remote,

you can set the dip switches to different

positions to have separate control.

Make wiring connections using wire

connectors provided as indicated above.

White from fan to White from remote

marked N. Black from fan to Black from

remote marked L. Blue from fan to Blue

from remote marked FOR LIGHT. White

from house to White from remote marked

AC N. Black from house to Black from

remote marked AC L. Connect all green

grounded wires to Grounded wire from

House. Make sure that no ﬁlaments are

outside of the wire connectors.

Insert the remote receiver into mounting

bracket.

Lift Canopy, allowing the 2 studs to

protrude through the canopy.

Install knurled nuts provided and tighten

the knurled nuts securely. The canopy

should adjust for any irregularity in the

ceiling or outlet box.

Make sure the studs protruding from the

bottom of the Mounting bracket are

installed with threads all the way through

the bracket.

Clip the decorative chains in the rings on

top housing and the hub installed on

downrod and then pull the hub up until

tight and tighten the set screw with

downrod on hub.

SAFETY CABLE INSTALLATION

Dip switches

Lag screw

Safety cable

Washer

Lock washer

Stud

Tab

Slot

Wall switch

Black

White

Ground/Green

White

Blue

Black

Receiver

Hub

13 14 15

16 17 18

Align the holes of blade bracket, blade

and the medallion of blade holder.

Install blade bracket with blade by 4

blade screws provided. Tighten screws

securely. Repeat this process for

remaining blades.

Loosen 2 and remove 1 preassembled

screw from the plate on motor. Save

screw for later use.

Attach light pan onto the plate on motor,

aligning the keyhole slots on the light

plate with the preassembled screws on

the plate. Twist clockwise till lock.

Reinstall the screw removed in step 15.

Tighten all screws securely.

Loosen 2 and remove 1 preassembled

screw from light pan. Save screw for later

use.

Remove ﬁnial, ﬁnal cap, hex nut and

silicon washer from light ﬁxture. Keep

parts.

Connect white wire from fan to white wire

from LED light kit and then connect blue

wire from fan to black wire from LED

light kit.

Attach LED light kit onto the light pan,

aligning the keyhole slots on the LED light

kit with the preassembled screws on the

light pan. Twist clockwise till lock.

Reinstall the screw removed in step 17.

Tighten all screws securely.

Remove shipping stabilizers from motor

assembly.

Insert blade assembly into the slot on

ﬂywheel.

Install blade assembly with screws

provided, aligning each of the holes as

shown and tighten all screws securely.

Repeat this process for remaining blades.

Note: Make sure the side with blade arm

medallion is installed downward.

Blade

Blade bracket

Blade arm medallion

Blade assembly

Shipping

stabilizer

Light pan

Light ﬁxture

Silicon washer

Hex nut

Final cap

Finial

Light pan

Light ﬁxture

19 20 21

22 23

Attached glass onto light ﬁxture and

install the silicon washer and hex nut

removed in step 17 to hold the glass.

Install ﬁnial cap and the ﬁnial removed in

step 17. Hand tighten the ﬁnial securely.

Remove battery cover. Install 12V battery

into wall remote. Duracell MN21 /

Evereday A23 / GP 23A all 12V. Attach

cover of remote by placing over buttons

and snap the battery cover in place.

Place battery cover over battery

compartment and buttons. Place remote

over 2 pins on front cover. Attach cover

of remote by placing over 4 pins and

snapping into place.

Install wall control unit to outlet box using

machine screws provided.

Attach front cover to wall control unit with

screws provided. Snap battery cover in

place

Battery cover

Battery

HAND HELD INSTALL

WALL MOUNT INSTALL

FAN SPEED: Depress “1 dot” for low speed, “2 dots” for medium or “3 dots” for high. To turn fan off press square”.

LIGHT DIMMER: To turn light on, press light dimmer once quickly. To turn off press once quickly while light is on. To dim light

hold down button “light dimmer”. The light will cycle from bright to dim to bright until button is released. Light will maintain last

setting if turned off.

FORWARD/REVERSE: Depress reverse button with fan running. Allow a few seconds for fan to slow down and change rotation

direction. Clicking noise may be heard after depressing button.

Note: If not using for long periods of time, remove battery to prevent damage to remote transmitter, and store the remote

transmitter away from excess heat or humidity

Remote Control Transmitter Features

MEDIUM SPEED

HIGH SPEED

LED LIGHT

LOW SPEED

FAN OFF SETTING

(Turn fan off only)

FAN REVERSE (Press

once to change direction

of the fan) Fan must be

running to reverse.

LIGHT ON/OFF SETTING

AND DIMMER (Press and

hold to dim light infinitely)

Trouble Shooting

,I\RXKDYHGLI¿FXOW\RSHUDWLQJ\RXUQHZFHLOLQJIDQLWPD\EHWKHUHVXOWRILQFRUUHFWDVVHPEO\LQVWDOODWLRQ

RUZLULQJ,QVRPHFDVHVWKHVHLQVWDOODWLRQHUURUVPD\EHPLVWDNHQIRUGHIHFWV,I\RXH[SHULHQFHDQ\IDXOWV

SOHDVHFKHFNWKLV7URXEOH6KRRWLQJ&KDUW,IDSUREOHPFDQQRWEHUHPHGLHGRU\RXDUHH[SHULHQFLQJGLI¿FXOW\LQ

LQVWDOODWLRQSOHDVHFDOORXU&XVWRPHU6HUYLFH&HQWHUDWWKH

QXPEHUSULQWHGRQ\RXUSDUWVOLVWLQVHUWVKHHW

Warning%HIRUHVHUYLFLQJRUFOHDQLQJXQLW6ZLWFKSRZHURIIDW6HUYLFHSDQHODQGORFNVHUYLFHGLVFRQQHFWLQJ

PHDQVWRSUHYHQWSRZHUIURPEHLQJVZLWFKHGRQDFFLGHQWDOO\:KHQWKHVHUYLFHGLVFRQQHFWLQJPHDQVFDQQRWEH

ORFNHGVHFXUHO\IDVWHQDSURPLQHQWZDUQLQJGHYLFHVXFKDVDWDJWRWKHVHUYLFHSDQHO

&KHFNPDLQDQGEUDQFKFLUFXLWIXVHVRUFLUFXLWEUHDNHUV

&KHFNOLQHZLUHFRQQHFWLRQVWRIDQDQGVZLWFKZLUHFRQQHFWLRQVLQVZLWFKKRXVLQJ

CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRII

,IWKLVIDQXVHV PDQXDO IRUZDUGUHYHUVHVZLWFKPDNHVXUHWKH VZLWFK LV SXVKHG ¿UPO\

HLWKHUZD\)DQZLOOQRWRSHUDWHZKHQVZLWFKLVLQWKHPLGGOH

,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNH

VXUHEDWWHU\LVHIIHFWLYH

&KHFNWRPDNHVXUHDOOVFUHZVLQPRWRUKRXVLQJDUHVQXJQRWRYHUWLJKWHQHG

&KHFNWRPDNHVXUHWKHVFUHZVZKLFKDWWDFKWKHIDQEODGHKROGHUWRWKHPRWRUDUHWLJKW

&KHFNWRPDNHVXUHZLUHQXWFRQQHFWRUVLQVZLWFKKRXVLQJDUHQRWUDWWOLQJDJDLQVWHDFK

RWKHURUDJDLQVWWKHLQWHULRUZDOORIWKHVZLWFKKRXVLQJ

CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRIIEHIRUHHQWHULQJVZLWFKKRXVLQJ

&KHFNWREHVXUHOLJKWEXOELVWLJKWLQVRFNHWDQGQRWWRXFKLQJWKHJODVVVKDGH

6RPHIDQPRWRUVDUHVHQVLWLYHWRVLJQDOVIURP6ROLG6WDWHYDULDEOHVSHHGFRQWUROV

$OORZEUHDNLQSHULRGRIKRXUV0RVWQRLVHVDVVRFLDWHGZLWKDQHZIDQZLOOGLVDSSHDU

DIWHUWKLVSHULRG

,IWKLVLV DGRZQURGPRXQWIDQ PDNHVXUHWKH ULGJH RQPRXQWLQJEUDFNHWHQJDJHVWKH

QRWFKLQWKHGRZQURGEDOO

0DNHVXUH WKDW FDQRS\ PRXQWLQJEUDFNHWRU PRXQWLQJ SODWHDUH WLJKWHQHG VHFXUHO\ WR

FHLOLQJMXQFWLRQER[DQGMXQFWLRQER[LVPRXQWHG¿UPO\WRFHLOLQJMRLVW

&KHFNWKDWDOOEODGHVDUHVFUHZHG¿UPO\LQWREODGHKROGHUV

&KHFNWKDWDOOEODGHKROGHUVDUHWLJKWHQHGVHFXUHO\WRPRWRU

0RVWIDQZREEOHSUREOHPVDUHFDXVHGZKHQEODGHOHYHOVDUHXQHTXDO&KHFNWKLVOHYHOE\

VHOHFWLQJDSRLQW RQWKHFHLOLQJDERYHWKHWLS RIRQHRIWKH EODGHV 0HDVXUHWKLVGLVWDQFH

IURPEODGHWLSWRFHLOQJ.HHSLQJPHDVXUHZLWKLQURWDWHWKHIDQXQWLOWKHQH[WEODGH

LVSRVLWLRQHG IRU PHDVXUHPHQW 5HSHDWIRUHDFKEODGH,IDOOEODGHOHYHOVDUHQRWHTXDO

\RXFDQDGMXVWEODGHOHYHOVE\WKHIROORZLQJSURFHGXUH7RDGMXVWDEODGHWLSGRZQLQVHUW

DZDVKHUQRWVXSSOLHGEHWZHHQWKHEODGHDQGEODGHKROGHUDWWKHVFUHZFORVHVWWRWKH

PRWRU7RDGMXVWDEODGHWLSXSLQVHUWZDVKHUQRWVXSSOLHGEHWZHHQWKHEODGHDQGEODGH

KROGHUDWWKHWZRVFUHZVIDUWKHVWIURP WKH PRWRU 5HYHUVHWKH SRVLWLRQ RI WKH ZDVKHULI

EODGHVPRXQWIURPWRSRIEODGH

,IEODGHZREEOHLV VWLOOQRWLFHDEOHLQWHUFKDQJLQJWZRDGMDFHQW VLGHE\VLGHEODGHVFDQ

UHGLVWULEXWHWKHZHLJKWDQGSRVVLEO\UHVXOWLQVPRRWKHURSHUDWLRQ

&KHFNEOXHZLUHIURPIDQWRPDNHVXUHLWLVFRQQHFWHGWRKRWZLUHIURPKRXVH

&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQIDQVZLWFKKRXVLQJ

&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQOLJKWNLW

&KHFNIRUIDXOW\OLJKWEXOEDQGPDNHVXUHEXOELVWLJKWLQVRFNHW

5HPRYHOLJKWNLWDQGFKHFNWKHSOXJFRQQHFWLRQVLIWKH\DUHSUHVHQW

,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNH

VXUHEDWWHU\LVHIIHFWLYH

CAUTION0DNHVXUH PDLQ SRZHU LV WXUQHG RII EHIRUH HQWHULQJ VZLWFK KRXVLQJ DQGRU

FDQRS\

,IIDQVRXQGVQRLV\

,IIDQZREEOHV

,IOLJKWGRHVQRWZRUN

,IIDQGRHVQRWVWDUW

Trouble Suggested Remedy

Nov.2013

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 8KGR72 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company BF2-WH Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LLR56 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Jovie 3JVR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DVR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DOR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3SY52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3HYR56**D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5KBR54 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MYR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ED56WAD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SH54XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ERAR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HM52XXN Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company MC263 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SBR56 D-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5FWR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HV52 F Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS52 D-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5VBR60 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HM52 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DIW52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5hM52XX series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung