Monte Carlo Fan Company 5BY52RB Gebrauchsanweisung

Owner’s Guide and Installation Manual

Attach sal s r c ipt to this card and r tain as your proof of purchas

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

To r gist r your fixtur , pl as visit our w bsit www.mont carlofans.com

5BY52XX Series Fan

Total fan w ight

UL Mod l No. : AC-552OD

11.84kgs

26.05 lbs

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA

70-1999), including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! ead all instructions and safety information before installing your new fan. eview the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the floor to the trailing edge of the blade.

WARNING: To educe The isk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and egulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not e-

move Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to

the building structure (or the ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed

control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, efrigeration and Air Conditioning Engineers (ASH AE) and the local code authorities.

CAUTION: To educe the isk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Note: Suitable for use in wet locations when installed in a GFCI protected branch circuit.

Note: Use only with light kits marked suitable for use in wet locations.

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

Tools equired for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,

Stepladder and Wire Strippers.

Place canopy and then yoke cover over downrod

as shown. Then thread the lead wires and safe-

ty cable from fan through the downrod as

shown.

Before you begin installing the fan, Switch power off

at Service panel and lock service disconnecting means

to prevent power from being switched on accidentally.

When the service disconnecting means cannot be

locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

Before installing this fan make sure the outlet

box is properly installed to the house structure.

To reduce the risk of fire, electric shock, or per-

sonal injury, mount to outlet box or supporting

system acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan support

(must support 35 lbs). Before attaching fan to

outlet box, ensure the outlet box is securely

fastened by at least two points to a structural

ceiling member ( a loose box will cause the fan

to wobble). Use only the screws provided

with the outlet box.

Remove keeper from pin. Pull pin out and

replace keeper, save for later.

Loosen the 2 set screws and nuts till you can

not feel them on inside of yoke.

Keeper

Tighen set screws and nuts to secure

downrod in yoke.

Insert downrod into yoke on top of

fan body. Align the hole in the down-

rod with hole in the yoke. Insert pin

through the yoke and downrod until

the point appears on the other side.

Install the keeper.

Check the fan motor for shipping sta-

bilizer and remove if present.

Carefully lift fan assembly onto mounting brack-

et. Rotate fan so that the notch on the ball

engages the ridge in the mounting bracket. This

will allow hands-free wiring.

Check the motor for shipping stabilizer

and remove if present. Attach blade

assembly to motor using the motor

screws and washers provided. Tighten

screws securely.

Remove 1 screw and loosen 2

screws.

Make wire connections to power source using

wire nuts provided. Make sure that no filiments

are outside of the wirenut. After making the

wire connections, the wires should be spread

apart with the grounded conductor and the

equipment-grounding conductor on one side of

the outlet box and ungrounded conductor on

the other side of the outlet box.

For pullchain controls, follow diagram above.

Make sure that all exposed wiring is secured

inside wire nuts. Note: Wires from house may

vary in color and may not include ground wire.

After wiring is conplete, gently push wires into

junction box with wire nuts pointing upward.

Refer to point 3 of safety tips.

For control of fan and optional light from wall

location, follow diagram above. NOTE: A profes-

sional electrician is recommended for this type

of installation.

Light Switch

Fan Switch

Wall

Control

Attach blade brackets to blades using

the blade bracket screws and wash-

ers provided. The blades will have a

label showing this side up on each

blade.

Loosen one and remove one pre-

assembled screw from mounting

bracket. Save screw. Lift canopy up,

aligning its keyhole slot with the pre-

assembled screw on mounting

bracket and twist clockwise to lock in

place. Re-install the removed screw

and tighten all screws securely.

For Canadian installation and for USA fan and light

kit combinations over 35 lbs, in both flush and

downrod modes the safety cable must be installed

into the house structure beams using 3” lag

screws, washers and lock washers provided. Make

sure that when the safety cable is fully extended

the lead wires are longer than the cable and no

stress is placed on the lead wires.

48+:If Installing The Secondary Support Safety

Cable in the U.S., Do Not Remove Knockouts In

The Outlet Box.

 Safety cable installation

!',+8='(1+

'-!)6+;

safety

cable

3” lag

screw

lock

washer

Push plug from fan and plug from

switch plate together. Match the

color strips on the plugs.

Remove the 3 screws from switch

cap.

Install switch plate by placing over

the 2 screws and twisting into place.

Install screw removed and tighten all

3 screws securely.

Black capacitor box needs to be

stuck to the switch housing. Not

being attached can cause motor

noise.

Remove twin adhesive tape from the

black capacitor as shown above.

Place and press firmly on the capaci-

tor to stick it to the switch housing.

Be sure it is secure.

Install switch cap into switch plate

housing, align the 3 holes and install

3 screws and tighten securely.

Setting the reverse switch in the

left hand side will result in down-

ward airflow and setting the

switch in the right hand side will

result in upward airflow.

Reverse switch

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

3.Make sure that any shipping stabilizer has been removed from motor.

CAUTION: Make sure main power is turned off.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.Some fan motors are sensitive to signals from Solid State variable speed controls. DO

NOT USE a Solid State variable speed control.

5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear

after this period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box

and junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is

positioned for measurement. Repeat for each blade. If all blade levels are not equal, you can

adjust blade levels by the following procedure. To adjust a blade tip down, insert a washer

(not supplied) between the blade and blade holder at the screw closest to the motor. To

adjust a blade tip up, insert washer (not supplied) between the blade and blade holder at

the two screws farthest from the motor. Reverse the position of the washer if blades mount

from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

1.Check wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

CAUTION: Make sure main power is turned off before entering switch housing.

2. If fan sounds noisy:

1. If fan does not

start:

3. If fan wobbles:

4. If light does not

work:

Trouble Shooting

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation,

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty

in installation, please call our Customer Service Center at the number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service dis-

connecting means to prevent power from being switched on accidentally. When the service dis-

connecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Trouble Suggested Remedy

Feb.2012 New format

Jul.2013 Update for CUL regulation

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company Mach One Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AVLR54 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 8TNR56 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3OVR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5COM52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CSM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DI52XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 14PRR62XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5EPR60BRD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 4TK52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ADR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AMR60BSD Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52XXD-L Series Fan Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Cupra 3CPR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Bravo 5BO52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5FWR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-552 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS52XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3CLYR52 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3IKR44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5VL52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5EM68 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Homeowner Max Plus 5HM52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3FSR52 series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung