Monte Carlo Fan Company 5DI52XXD-L Series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Attach sales receipt to this card and retain as your proo o purchase

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

To register your ixture, please visit our website www.montecarlo ans.com

5DI52XXD/5DI52XXD-L Series Fan

Total an weight with light

UL Model No. : 5DI52

8.5 kgs

18.7 lbs

WARNING: T REDUCE THE RISK F FIRE, ELECTRIC SH CK, R INJURY T PERS NS, BSERVE THE F LL WING: READ

AND SAVE THESE INSTRUCTI NS

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-1999), including

fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the

outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed carefully up

into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent

power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a

tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the

trailing edge of the blade.

WARNING: To Reduce The Risk f Fire, Electric Shock, or Personal Injury, Mount To utlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The utlet Box.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Re-

move Knockouts In The utlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to

the building structure (or the ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign

object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment manufac-

turer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigera-

tion and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlo ans.com

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,

Stepladder and Wire Strippers.

Before you begin installing the fan, Switch

power off at Service panel and lock service dis-

connecting means to prevent power from being

switched on accidentally. When the service dis-

connecting means cannot be locked, securely

fasten a prominent warning device, such as a

tag, to the service panel.

Before installing this fan make sure the outlet box is

properly installed to the house structure. To reduce

the risk of fire, electric shock, or personal injury,

mount to outlet box or supporting system acceptable

for fan support. (Mounting must support at least 35

lbs.)

Use metal outlet box suitable for fan support

(must support 35 lbs). Before attaching fan to

outlet box, ensure the outlet box is securley

fastened by at least two points to a structural

ceiling member ( a loose box will cause the fan

to wabble). Use only the screws provided

with the outlet ox.

Loosen the 2 set screws till you can not

feel them on inside of yoke.

Note: If install fan on vaulted ceiling,

make sure open end of mounting

bracket is installed facing the higher

point of the ceiling and make sure the

ceiling angle is not steeper

than 30º.

yoke

Place downrod into fan yoke.

Install the keeper to pin.

Align the hole in the Downrod with the hole in

the Yoke. Insert the Pin through the Yoke and

Downrod until the point appears on the other

side.

Downrod mount installation

Remove Keeper pin and cross pin

from downrod. Place canopy and

caonpy disk cover over downrod.

Canopy

Tread leadwires and safety

cable through downrod.

Downrod

Canopy

disk

Cross

Keeper

Downrod

Hang assembled fan from the mounting bracket in-

stalled to ceiling in previous step. Make sure the fan

is hanging straight. Rotate fan until the tab on the

Mounting bracket engages the slot on the Downrod

Ball. This must be done to prevent the fan body from

rotating when the blades are in motion.

Make wire connections to power source using wire nuts

provided. Make sure that no filiments are outside of

the wirenut. After making the wire connections, the

wires should be spread apart with the grounded con-

ductor and the equipment-grounding conductor on one

side of the outlet box and ungrounded conductor on the

other side of the outlet box.

Make sure the studs protruding from the

bottom of the Mounting bracket are in-

stalled with threads all the way through

the bracket.

Tighten the 2 set screws on the yoke

once the downrod is in place.

Make wiring connections as indicated

above. Connect black and blue wire from

fan to Black or (Hot) wire from house.

Connect White wire from Fan to White

( eutral) wire from house. Connect

Ground leads from mounting bracket and

downrod to Ground lead from house.

Refer to Safety Tips section of manual.

For Canadian installation and for USA fan and light

kit combinations over 35 lbs, in both flush and

downrod modes the safety cable must be installed

into the house structure beams using 3” lag

screws, washers and lock washers provided. Make

sure that when the safety cable is fully extended

the lead wires are longer than the cable and no

stress is placed on the lead wires.

Note:If Installing The Secondary Support Safety

Cable in the U.S., Do ot Remove Knockouts In

The Outlet Box.

12 Safety cable installation

Safety Ca le

Lag Screw

safety

cable

3” lag

screw

lock

washer

Remove every other screw as circled

and save for later use.

Note: Flushmount is not available

with vaulted ceiling.

Go to step 26

Flush mount installation

Cover

Ring

Lift Conopy allowing the 2 studs to

protrude through the canopy.

ext lift the cover ring and install knurled

nuts as shown. Tighten the knurled nuts

securely. The canopy should adjust for

any irregularity in the ceiling or Outlet

box.

Check the motor for shipping stabiliz-

ers and remove if present. Attach

blades using screws and washers in

hardware pak. Tighten screws se-

curely.

Remove side covers from canopy exposing

4 holes. 2 closed holes and 2 open “L”

shape holes and then Pass leadwires and

safety cable through the canopy.

“L” shape

slots

Install rubber pad between fan

body and canopy.

Remove the all thread studs from the

lower part of the mounting bracket. Hang

fan from mounting bracket by the

hands free hook into a closed hole on

the edge of the Canopy. Note: For

Canadian mounting refer to Step #12.

Hands free hook

Place canopy over fan body align-

ing holes.

Replace the 3 screws removed and

tighten securely. Check motor for

shipping stabilizers and remove if

present.

Take 4 screws from hardware pack

and install one on each side of

bracket to match the L slot screw

holes in canopy. Keep 2 screws for

later use.

Make wire connections to power source using wire nuts

provided. Make sure that no filiments are outside of

the wirenut. After making the wire connections, the

wires should be spread apart with the grounded con-

ductor and the equipment-grounding conductor on one

side of the outlet box and ungrounded conductor on the

other side of the outlet box.

Lift fan to mounting bracket, aligning the “L”

shape holes with the screws on the mounting

bracket. Turn the fan clockwise to lock in

position. Install the other 2 screws included

in hardware bag and tighten all 4 securely.

Make wiring connections as indicated

above. Connect black and blue wire from

fan to Black or (Hot) wire from house.

Connect White wire from Fan to White

( eutral) wire from house. Connect

Ground leads from mounting bracket and

downrod to Ground lead from house.

Refer to Safety Tips section of manual.

Install 3 screws to install light pan.

Connect plug from fan to switch

house plug. Be sure plugs connection

snap together completely.

Install by twisting clockwise, add 1

screw removed step 27 to switch

housing plate. Tighten the 3 screws

securely.

Connect white wire from fan to white

wire from light fixture. Then plug

blue wire from fan to black wire from

light fixture.

Loosen the pre installed screws of

switch housing plate. Save removed

screw for use later.

Install a JD 75 watt halogen bulb, bulb in-

cluded.

Caution: Do not replace bulb until it cools

down.

WARNING: Over lamping the fan will re-

sult in the fan lights shutting down until

the proper wattage of bulbs are installed.

Reset the lights by turning off the wall

switch, breaker,or by remote. Replace bulbs

with the correct wattage bulbs, turn the

power on.

Attach glass by locating dimples in

light fixture with the groves in glass

and twisting clockwise till tight.

Setting the reverse switch in the left hand

side will result in downward airflow and set-

ting the switch in the right hand side will re-

sult in upward airflow.

Note: Reverse switch must be set either

completely LEFT or completely Right for fan

to function. If the reverse switch is set in the

middle position, fan will not operate.

Reverse switch

Left hand side

(Forward)

Right hand side

(Reverse)

Loosen 2 screws and remove 1 screw

from motor plate. Save removed

screw for use later.

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

CAUTION: Make sure main power is turned off.

3.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate

when switch is in the middle.

4.Make sure that shipping stabilizer tabs have been removed from motor.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off efore entering switch housing.

4.If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glass-

ware are finger tight. Check to be sure light bulb is tight in socket and not touching glass

shade(s). If vibration persists from glass, remove glass and install a 1/4" wide rubber band

on glass neck to act as an insulator. Replace glass and tighten screws against rubber band.

5.Some fan motors are sensitive to signals from Solid State variable speed controls. DO NOT

USE a Solid State varia le speed control.

6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear

after this period.

1.If this is a downrod mount fan, make sure the ridge on mounting bracket engages the

notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box

and junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance from

blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is posi-

tioned for measurement. Repeat for each blade. If all blade levels are not equal, you can ad-

just blade levels by the following procedure. To adjust a blade tip down, insert a washer (not

supplied) between the blade and blade holder at the screw closest to the motor. To adjust a

blade tip up, insert washer (not supplied) between the blade and blade holder at the two

screws farthest from the motor. Reverse the position of the washer if blades mount from top

of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can re-

distribute the weight and possibly result in smoother operation.

1.Check blue wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

WARNING: Over lamping the fan will result in the fan lights shutting down

until the proper wattage of ul s are installed.

Reset the lights y turning off the wall switch, reaker,or y remote. Replace ul s

with the correct wattage ul s, turn the power on.

CAUTION: Make sure main power is turned off efore entering switch housing.

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not work:

TROUBLE SHOOTI G

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or

wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please

check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installa-

tion, please call our Customer Service Center at the

number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service discon-

necting means to prevent power from eing switched on accidentally. When the service disconnecting

means cannot e locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Trou le Suggested Remedy

Apr.2013

May.2013 CUL requirement

Aug.2013 dual mount

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 3DIR52 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MHR52RBD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 4BFR54 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CXR52 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Linden 3LD48 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5UPR54 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3JVR44 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ML52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5VL52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ALMSM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3OBSHR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CLR66XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LOR52BSD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MYR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DI52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3OVR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3DIR58RBD-V1 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Crystoria Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BS52 Builder Supreme Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ACR52XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LLR56 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4GIR60ATIHAB Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DOR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5KBR54 Series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung