Monte Carlo Fan Company 5LLR56 D-V1 Series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Total fan weight with light

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as yourproof of purchase

To register your fixture, please visit our website www.montecarlofans.com

5LLR56XXD-V1 Series Fan

ETL Model NO. : 5LLR56(X)

8 kgs

17.6 lbs

Cautions and Warnings

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA

70-1999), including ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the ﬂoor to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the

building structure (or the ceiling joist).

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To Reduce The Risk Of Electric Shock, This Fan Must Be Installed With a general use, isolating Wall Control/Switch.

WARNING: To reduce the risk of ﬁre or electric shock, this fan should only be used with fan speed control part no. DC8 manufactured by

Carewell Electric Technology (Zhongshan) Co.,Ltd.

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any other solid state fan speed control device, or variable

speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

CAUTION: The light source is designed for this speciﬁc application and can overheat if serviced by untrained personnel. If any servicing is

required, the product should be returned to an authorized service facility for examination or repair.

All set screws must be checked, and re-tightened where necessary, before installation.

Note: Suitable for use in damp locations.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

1 2 3

4 5 6

OFF

Before you begin installing the fan, Switch

power off at Service panel and lock

service disconnecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be locked,

securely fasten a warning device, such

as a tag, to the service panel.

Use AC 120V/60HZ power supply

only.

Before installing this fan make sure the

outlet box is properly installed to the

house structure. To reduce the risk of

ﬁre, electric shock, or personal injury,

mount to outlet box or supporting system

acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan

support and use only the screws provided

with the outlet box (must support 35 lbs).

Before attaching fan to outlet box, ensure

the outlet box is securely fastened by at

least two points to a structural ceiling

member (a loose box will cause the fan to

wobble). Remove the two outlet box

screws provided with the box, aligning

the holes of the mounting bracket with

the holes of the outlet box. Reinstall the 2

outlet box screws securely.

Remove preassembled keeper pin and

cross pin from downrod.

Place downrod over canopy and yoke

cover

Partially loosen downrod set screws from

yoke at top of motor assembly.

Thread lead wires and safety cable from

motor assembly through downrod.

Helpful hint: For easy assembling of the

cross pin on the next installation step.

After slip downrod into the motor yoke,

carefully insert a Phillips screwdriver through

the yoke and downrod (don’t damage the

lead wires) as a guide and then push the

cross pin and pull the screwdriver in the

meantime as shown in the inset.

Mounting bracket

Canopy

Downrod

Keeper pin

Cross pin

Downrod

Yoke cover

Downrod Mount Installation

Canopy

Downrod

Yoke cover

Yoke

Lead wire Safety

cable

Cross

Screwdriver

Set screw

7 8 9

Slip downrod into motor housing yoke,

aligning holes and install cross pin and keeper

pin.

Insert cross pin through yoke and downrod

until point appears on the other side, and

insert keeper pin on cross pin.

Pull the downrod up tight against the cross

pin, and then evenly tighten the downrod set

screws on motor housing yoke.

Place Yoke cover on motor assembly.

Warning: Cross pin and keeper pin must be

installed securely, failure to install them will

result in serious injury.

Install ball end of downrod into mounting

bracket opening. Align (engage) slot on

ball with tab on mounting bracket.

Warning: Failure to align slot on ball with

tab may result in serious injury.

Important: If using the angle mount,

make sure open end of mounting bracket

is installed facing the higher point of the

ceiling and make sure the ceiling angle is

not steeper

than 15º.

For Canadian installation and for USA fan

and light kit combinations over 35 lbs, in

both ﬂush and downrod modes the safety

cable must be installed into the house

structure beams using 1.5” lag screws,

washers and lock washers provided.

Make sure that when the safety cable is

fully extended the lead wires are longer

than the cable and no stress is placed on

the lead wires.

Note: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box.

Make wiring connections using wire connectors provided as indicated above.

Red from fan to Red from remote marked Motor 1.

Purple from fan to Purple from remote marked Motor 2.

Gray from fan to Gray from remote marked Motor 3.

Blue from fan to Blue from remote marked FOR LIGHT.

White from fan to White from remote marked FOR LIGHT.

White (Neutral) from house to White from remote marked AC IN N.

Black (Live) from house to Black from remote marked AC IN L.

Connect all green grounded wires to Grounded wire from House.

Make sure that no ﬁlaments are outside of the wire connectors.

Insert the remote receiver into mounting bracket.

After making the wire connections, the wires should be spread apart with the grounded

conductor and the equipment-grounding conductor on one side of the outlet box and

ungrounded conductor on the other side of the outlet box. The splices after being made should

be turned upward and pushed carefully up into the outlet box.

Yoke

Tab

Downrod

Slot

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

Blue (For Light)

White (For Light)

Red (Motor 1)

Purple (Motor 2)

Gray (Motor 3)

Black (AC IN L)

White (AC IN N)

Green/Ground

Wall Switch

Ground/Green

Black (Live)

White (Neutral)

Power source

Receiver

Yoke cover

Downrod

Set screws Keeper pin

Cross pin

11 12 13

14 15 16

Partially loosen 2 of the set screws on

mounting bracket corresponding to the

slotted holes on the canopy upper ring.

Remove the other 2 set screws. Save

screws.

Remove every other screws (the screws

located at round holes) from yoke located

on top of fan assembly. Keep screws.

Remove canopy bottom cap from canopy.

Note: Flush mount is not available with

vaulted ceiling.

Place canopy over lead wire and safety

cable and align the larger holes in canopy

with the set screws on yoke.

Reinstall the 3 set screws remove in step

13. Tighten screws securely.

To prepare the fan for wiring, hang fan

onto mounting bracket by sliding the

canopy over the mounting bracket hook

(Use one of non-slotted holes on the

rim of the canopy).

For Canadian installation and for USA fan

and light kit combinations over 35 lbs, in

both ﬂush and downrod modes the safety

cable must be installed into the house

structure beams using 1.5” lag screws,

washers and lock washers provided.

Make sure that when the safety cable is

fully extended the lead wires are longer

than the cable and no stress is placed on

the lead wires.

Note: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box.

Raise canopy to mounting bracket,

aligning loosened screws in mounting

bracket with slotted holes in canopy.

Twist canopy to lock. Reinstall the screws

removed in step 11 and tighten all

screws securely.

Go to step 20 to ﬁnish installation

Mounting bracket

Flush Mount Installation

Canopy

Canopy bottom cap

Mounting bracket

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

Canopy

17 18

19 20 21

Make wiring connections using wire connectors provided as indicated above.

Red from fan to Red from remote marked Motor 1.

Purple from fan to Purple from remote marked Motor 2.

Gray from fan to Gray from remote marked Motor 3.

Blue from fan to Blue from remote marked FOR LIGHT.

White from fan to White from remote marked FOR LIGHT.

White (Neutral) from house to White from remote marked AC IN N.

Black (Live) from house to Black from remote marked AC IN L.

Connect all green grounded wires to Grounded wire from House.

Make sure that no ﬁlaments are outside of the wire connectors.

Insert the remote receiver into mounting bracket.

Partially loosen 2 of the set screws on

mounting bracket corresponding to the

slotted holes on the canopy upper ring.

Remove the other 2 set screws. Save

screws.

Raise canopy to mounting bracket,

aligning loosened screws in mounting

bracket with slotted holes in canopy. Twist

canopy to lock. Reinstall the screws

removed in step 18 and tighten all screws

securely.

Align the holes of blade bracket, blade

and the top plate of blade bracket.

Install blade bracket with blade by 4 blade

screws provided. Tighten screws securely.

Repeat this process for remaining blades.

Install the blade assembly to motor using

the set screws provided. Tighten screws

securely

Repeat this process for remaining blade

assemblies.

Loosen 2 and remove 1 preassembled set

screws from the plate on motor. Save

screw for later use.

Blade

Blade assembly

Top plate

Blue (For Light)

White (For Light)

Red (Motor 1)

Purple (Motor 2)

Gray (Motor 3)

Black (AC IN L)

White (AC IN N)

Green/Ground

Wall Switch Black (Live)

White (Neutral)

Power source

Blade bracket

Receiver

22 23 24

25 26

Attach light plate onto the plate on motor,

aligning its keyhole slots with the

preassembled set screws on the plate and

twist clockwise till lock. Reinstall the

screw removed in step 21. Tighten all

screws securely.

Connect white wire from fan to white wire

from light ﬁxture, and then connect blue

(or black) wire from fan to blue (or black)

wire from light ﬁxture.

Attach light ﬁxture onto the light plate,

aligning keyhole slots on the light ﬁxture

with the preassembled set screws on

light plate and twist clockwise until lock.

Reinstall the screw removed in step 23.

Tighten all screws securely.

Place glass over glass ﬁxed ring, aligning

the thread on light ﬁxture and attach it

onto light ﬁxture by turning clockwise till

tight.

Loosen 2 and remove 1 preassembled set

screws from the light plate. Save screw for

later use.

Light plate

Glass

Glass holder

Light ﬁxture

REMOTE CONTROL SETTING and OPERATION

Universal Mode and Learning Mode

There are “Universal Mode” and “Learning Mode” with the remote controller.

If choosing “Universal Mode”, simply place dip (code) switch at UPPER

position. Your fan with the remote controller is ready to use.

Note: If using universal mode, your fan can be controlled with other remote

transmitters with the same setting.

To control the fan with speciﬁc remote transmitter, choose “Learning Mode”

by placing the dip (code) switch at LOWER position and then make learn

function setting as below.

Learn function setting, Restore power source to your fan, press and hold

the “LEARN” button for at least 3 seconds. You must press the “LEARN”

button within 60 seconds of restoring power to the fan.

Note: If the power is on already, you must turn the power off for 10 seconds

at least, and then turn the power back for remote control learn function

setting.

Note: If the fan is installed with light, light will twinkle 2 times. The remote

control setting process is complete and your fan is ready for use. For fans

without light, check operation using remote transmitter.

Note: If you want to control the fan with another transmitter, make the same

setting. A fan can be controlled by 2 transmitters maximum.

Transmitter Operation

Remove the battery cover from the remote control transmitter and install

battery, battery provided. Replace the cover.

Note: Use 2 1.5V/AAA battery.

Note: If not using for long period of time, remove battery to prevent damage

to remote transmitter, and store the remote transmitter away from excess heat

or humidity.

DIM

LEARN

L.CODE

COMMON

CODE

L.CODE

COMMON

CODE

DIM

Universal Mold

Learning Mold

Dimming / Non Dimming Setting

The “DIM” selection is the light dimmable selection and the light will cycle

from bright to dim to bright until button is released. The “ON” selection is the

light ON/OFF only (non dimming function). Light will maintain last setting if

turned off.

Note: The remote controller is set with dimming function at factory,

Note: If the remote receiver has been wired with fan, turn power off by wall

switch before switch “DIM” and “ON/OFF” selection.

Dimming/

Non dimming

LEARN

Learn

The receiver provides the following protective functions

Lock protection- The DC motor has a build-in safety feature against blade or motor obstruction during operation. If

something obstructs the fan blades or motor, the motor will keep trying to run for 5 times and then stop operation

after about 60 seconds of interruption. Please remove obstacles and reset. To reset it by turn the fan off by remote

transmitter and then turn the fan on, Or you may turn power off for 15 seconds then turn power back, and then turn

the fan on,

Over load protection (current limit)- The device will limits the maximum current output from the receiver/drive when the

fan or light load was increased abnormally.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS

SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1)THIS DEVICE MAY NOT

CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY

INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE

UNDESIRED OPERATION.

The buttons on the remote control transmitter control the fan speed and light as follows.

Fan speed

1 = minimum speed 2 = low speed

3 = medium low speed 4 = medium speed

5 = medium high speed 6 = high speed

This button turns the fan off.

Forward/Reverse button- This button is to control direction of fan rotation. Press once

to change direction of the fan rotation. Fan must be running to reverse.

Light button- Press this button to turn light on or off. To dim light (

Setting at “DIM”

position

), hold down the button, the light will cycle from bright to dim to bright until button

is released.

Note

: This remote controller has auto resume function, the fan and light will maintain the

last setting if power is turned off.

Tips for end users

1. If your fan is operated automatically after installation and power on, it is because your fan is still memorize the previous

setting at factory.

2. If fan or light isn’t working, reset power (turn the power off for at least 10 seconds and then turn the power back) and redo

the learn function setting.

3. It is not available to separately operate the learn setting for more than one fan in the same room (in the area where remote

signal can reach to) if they share the same power supply. Separate power supplies (like as using individual wall switches for each

fan and turn power off for the fan while you are making learn function for other fan) is required if you want to separately control

more than one fan in same room.

4. When fan is turned on or operated forward/reverse function, it shutters & goes back & forth until it turns. It is a normal

performance of this fan and it will take for few seconds to run this operation.

Install Transmitter wall mount cradle with 2 screws provided.

Wall mount cradle installation

Trouble Shooting

,I\RXKDYHGLI¿FXOW\RSHUDWLQJ\RXUQHZFHLOLQJIDQLWPD\EHWKHUHVXOWRILQFRUUHFWDVVHPEO\LQVWDOODWLRQ

RUZLULQJ,QVRPHFDVHVWKHVHLQVWDOODWLRQHUURUVPD\EHPLVWDNHQIRUGHIHFWV,I\RXH[SHULHQFHDQ\IDXOWV

SOHDVHFKHFNWKLV7URXEOH6KRRWLQJ&KDUW,IDSUREOHPFDQQRWEHUHPHGLHGRU\RXDUHH[SHULHQFLQJGLI¿FXOW\LQ

LQVWDOODWLRQSOHDVHFDOORXU&XVWRPHU6HUYLFH&HQWHUDWWKH

QXPEHUSULQWHGRQ\RXUSDUWVOLVWLQVHUWVKHHW

Warning%HIRUHVHUYLFLQJRUFOHDQLQJXQLW6ZLWFKSRZHURIIDW6HUYLFHSDQHODQGORFNVHUYLFHGLVFRQQHFWLQJ

PHDQVWRSUHYHQWSRZHUIURPEHLQJVZLWFKHGRQDFFLGHQWDOO\:KHQWKHVHUYLFHGLVFRQQHFWLQJPHDQVFDQQRWEH

ORFNHGVHFXUHO\IDVWHQDSURPLQHQWZDUQLQJGHYLFHVXFKDVDWDJWRWKHVHUYLFHSDQHO

&KHFNPDLQDQGEUDQFKFLUFXLWIXVHVRUFLUFXLWEUHDNHUV

&KHFNOLQHZLUHFRQQHFWLRQVWRIDQDQGVZLWFKZLUHFRQQHFWLRQVLQVZLWFKKRXVLQJ

CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRII

,IWKLVIDQXVHV PDQXDO IRUZDUGUHYHUVHVZLWFKPDNHVXUHWKH VZLWFK LV SXVKHG ¿UPO\

HLWKHUZD\)DQZLOOQRWRSHUDWHZKHQVZLWFKLVLQWKHPLGGOH

,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNH

VXUHEDWWHU\LVHIIHFWLYH

&KHFNWRPDNHVXUHDOOVFUHZVLQPRWRUKRXVLQJDUHVQXJQRWRYHUWLJKWHQHG

&KHFNWRPDNHVXUHWKHVFUHZVZKLFKDWWDFKWKHIDQEODGHKROGHUWRWKHPRWRUDUHWLJKW

&KHFNWRPDNHVXUHZLUHQXWFRQQHFWRUVLQVZLWFKKRXVLQJDUHQRWUDWWOLQJDJDLQVWHDFK

RWKHURUDJDLQVWWKHLQWHULRUZDOORIWKHVZLWFKKRXVLQJ

CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRIIEHIRUHHQWHULQJVZLWFKKRXVLQJ

&KHFNWREHVXUHOLJKWEXOELVWLJKWLQVRFNHWDQGQRWWRXFKLQJWKHJODVVVKDGH

6RPHIDQPRWRUVDUHVHQVLWLYHWRVLJQDOVIURP6ROLG6WDWHYDULDEOHVSHHGFRQWUROV

$OORZEUHDNLQSHULRGRIKRXUV0RVWQRLVHVDVVRFLDWHGZLWKDQHZIDQZLOOGLVDSSHDU

DIWHUWKLVSHULRG

,IWKLVLV DGRZQURGPRXQWIDQ PDNHVXUHWKH ULGJH RQPRXQWLQJEUDFNHWHQJDJHVWKH

QRWFKLQWKHGRZQURGEDOO

0DNHVXUH WKDW FDQRS\ PRXQWLQJEUDFNHWRU PRXQWLQJ SODWHDUH WLJKWHQHG VHFXUHO\ WR

FHLOLQJMXQFWLRQER[DQGMXQFWLRQER[LVPRXQWHG¿UPO\WRFHLOLQJMRLVW

&KHFNWKDWDOOEODGHVDUHVFUHZHG¿UPO\LQWREODGHKROGHUV

&KHFNWKDWDOOEODGHKROGHUVDUHWLJKWHQHGVHFXUHO\WRPRWRU

0RVWIDQZREEOHSUREOHPVDUHFDXVHGZKHQEODGHOHYHOVDUHXQHTXDO&KHFNWKLVOHYHOE\

VHOHFWLQJDSRLQW RQWKHFHLOLQJDERYHWKHWLS RIRQHRIWKH EODGHV 0HDVXUHWKLVGLVWDQFH

IURPEODGHWLSWRFHLOQJ.HHSLQJPHDVXUHZLWKLQURWDWHWKHIDQXQWLOWKHQH[WEODGH

LVSRVLWLRQHG IRU PHDVXUHPHQW 5HSHDWIRUHDFKEODGH,IDOOEODGHOHYHOVDUHQRWHTXDO

\RXFDQDGMXVWEODGHOHYHOVE\WKHIROORZLQJSURFHGXUH7RDGMXVWDEODGHWLSGRZQLQVHUW

DZDVKHUQRWVXSSOLHGEHWZHHQWKHEODGHDQGEODGHKROGHUDWWKHVFUHZFORVHVWWRWKH

PRWRU7RDGMXVWDEODGHWLSXSLQVHUWZDVKHUQRWVXSSOLHGEHWZHHQWKHEODGHDQGEODGH

KROGHUDWWKHWZRVFUHZVIDUWKHVWIURP WKH PRWRU 5HYHUVHWKH SRVLWLRQ RI WKH ZDVKHULI

EODGHVPRXQWIURPWRSRIEODGH

,IEODGHZREEOHLV VWLOOQRWLFHDEOHLQWHUFKDQJLQJWZRDGMDFHQW VLGHE\VLGHEODGHVFDQ

UHGLVWULEXWHWKHZHLJKWDQGSRVVLEO\UHVXOWLQVPRRWKHURSHUDWLRQ

&KHFNEOXHZLUHIURPIDQWRPDNHVXUHLWLVFRQQHFWHGWRKRWZLUHIURPKRXVH

&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQIDQVZLWFKKRXVLQJ

&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQOLJKWNLW

&KHFNIRUIDXOW\OLJKWEXOEDQGPDNHVXUHEXOELVWLJKWLQVRFNHW

5HPRYHOLJKWNLWDQGFKHFNWKHSOXJFRQQHFWLRQVLIWKH\DUHSUHVHQW

,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNH

VXUHEDWWHU\LVHIIHFWLYH

CAUTION0DNHVXUH PDLQ SRZHU LV WXUQHG RII EHIRUH HQWHULQJ VZLWFK KRXVLQJ DQGRU

FDQRS\

,IIDQVRXQGVQRLV\

,IIDQZREEOHV

,IOLJKWGRHVQRWZRUN

,IIDQGRHVQRWVWDUW

Trouble Suggested Remedy

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS52 D-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HDR52D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3STMSM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CNR52 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DCR52XX Fan Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MX series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3CLMR56XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5OBR52 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ACR52XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DIW52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CSR60AGD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5COM52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3IKR44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR60RZW Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3SU54 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BY52XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3DIR58 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3RZHR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-552 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4MC20XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5VMR72 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR99 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TAHR56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CQM44 Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung