Moxa Technologies VPort 461 Series Bedienungsanleitung

Moxa Industrial Video Encoder

VPort 461 Series

Quick Installation Guide

First Edition, November 2009

Reproduction without permission is prohibited.

Fl.4, No.135, Lane 235, Pao-Chiao Rd. Shing Tien City, Taipei, Taiwan,

R.O.C.

TEL: +886-2-8919-1230

P/N: 1802004610010

- 2 -

Overview

The VPort 461 is a 1-channel Industrial Video Encoder with H.264 video

compression. The H.264 algorithm provides the best video quality on the

market today with lower bandwidth requirements than other video compression

standards. In addition, to meet requirements for multiple video streams, the

VPort 461 can provide up to 3 video streams simultaneously with H.264 and

MJPEG compression. Users can use the video streams for different purposes,

such as viewing, recording or analysis. Finally, the industrial-rugged design,

with -40 to 75°C operating temperature, built-in fiber Ethernet ports, IP30 form

factor protection, and industrial certifications, make the VPort 461 suitable for

the harsh environment.

Package Checklist

The VPort 461 ships with the following items:

yVPort 461.

y6-pin terminal block for 1 power input and 2 digital inputs.

y8-pin terminal block for the other power input, and 2 relay outputs.

y5-pin terminal block for the RS-232/422/RS-485 PTZ control port.

yQuick Installation Guide.

yDocument & Software CD (includes User’s Manual, Quick Installation

Guide, Moxa IVN Solution Datasheet and Utility).

yWarranty Card.

Note: If any of these items are missing or damaged, please contact your

customer service representative for assistance.

NOTE Check the model name on the VPort’s side label to determine if the

model name is correct for your order.

NOTE This product must be installed in compliance with your local laws

and regulations.

Features

High Performance Audio-Video Networking Solution

•Works with NTSC/PAL analog video cameras.

•Supports H.264/MJPEG video compression technologies.

•Up to 3 simultaneous video streams (2 H.264 and 1 MJPEG).

•Lower latency, under 200 ms.

•1 BNC video input.

•Video stream up to 30 frames/sec in Full D1 (720 x 480) resolution in

NTSC, and 25 frames/ sec in Full D1 (720 x 576) resolution in PAL.

•Select between Full D1/ 4CIF/ VGA/ CIF/ QCIF resolutions.

•1 audio input and 1 audio output for 2-way voice communication.

•TCP, UDP, and HTTP network transmission modes.

- 3 -

•Supports Modbus/TCP for easy communication with SCADA systems.

•Suppoerts standard RTSP (Real-time streaming protocol) for easy

integration.

•Supports multicast (IGMP) protocols for efficient network transmission.

•Supports QoS (TOS) for priority transmission.

•Supports SNMP V1/V2c/V3 for network management.

•Built-in web server and RS-232 console for remote access and

configuration.

•Supports one SD card slot (SDHC inteface) for local video recording on

the SD card during network interruptions.

•Two auto-sensing 10/100BaseT(X) Ethernet ports.

•Maximum 10 output video streams and 10 client connections.

•Set up video quality in CBR (constant bit rate) or VBR (variable bit rate).

•Supports 1 RS-232/422/485 DB9 COM port for controlling a PTZ

(PAN/TILT/ZOOM) motorized camera or serial device via a TCP/IP

network.

•Supports 1 RS-232/RS-422/RS-485 5-pin PTZ port for controlling a PTZ

(PAN/TILT/ZOOM) motorized camera via a TCP/IP network.

•UPnP and IP filtering supported.

Rugged Industrial Design

yTwo 12/24 VDC and 24 VAC redundant power inputs with LED indicators

y-40 to 75°C operating temperature for harsh industrial environments

(“T” model)

y35 mm DIN-Rail mounting or panel mounting installation

(with optional accessory)

yIP30 form factor protection

yCE, FCC, UL508 approvals for industrial applications

Intelligent Alarm Trigger Capability

yBuilt-in Video Motion Detection (VMD) (firmware version V2.0 and later)

yEquipped with 2 DIs and 2 relays (DO) for external sensors and alarms.

yPre, trigger, and post alarm snapshot images provided.

ySupports sequential snapshot images

yMessages with snapshot images can be sent via FTP and email.

yCapable of setting an alarm schedule

Video Management and Control

yFree Moxa VPort SDK Plus (software development kits) supported with

flexible interface and sample codes for customized application or system

integration.

yMoxa SoftNVR-IA IP surveillance software supported for the video

recording and management solution.

NOTE VMD alarms are supported by V2.0 firmware version and later

- 4 -

NOTE If you are interested in the Moxa VPort SDK PLUS, please go to

Moxa’s website (www.moxa.com) to download the software, or

contact a Moxa sales representative for more information.

NOTE If you are interested in SoftNVR-IA IP surveillance software,

please go to Moxa’s website (www.moxa.com) to download the

trial version.

- 5 -

VPort 461 Panel Layout

Front Panel View

Top Panel View

Rear Panel View

RS-232

CONSOLE

1. Grounding screw

2. RS-232 console port

3. Hardware reset button

4. 8-pin terminal block for Relay

1, Relay 2, and power input 1

(PWR1)

5. 6-pin terminal block for DI 1,

DI 2, power input 2 (PWR2)

6. Heat dissipation orifices

7. LEDs for STAT, PWR1,

PWR2, FAULT

8. LEDs for VIDEO, PTZ and SD

9. SD card (SDHC) slot

10. 2 RJ45 10/100BaseTX

Ethernet port with 10 /100

Mbps LED

11. AUDIO OUTPUT port for

external speaker

12. AUDIO INPUT port for mic-in

and line-in connection

13. RS-232/422/485 COM port

with DB9 male connector for

PTZ camera or serial device

control

14. RS-232/422/485 PTZ port

with 5-pin terminal block for

PTZ camera control

15. 1 BNC connector for video

input

16. Model name

17. Screw hole for wall mounting

kit

18. DIN-Rail mounting kit

- 6 -

First-Time Installation and

Configuration

Before installing the VPort 461, check to make sure that all items in the

package checklist are in the box. In addition, you will need access to a

notebook computer or PC equipped with an Ethernet port.

Step 1: Select the Power Source

The VPort 461 can be powered by a DC power input from 12 to 32 VDC, or an

AC power input from 18 to 30 VAC. Two power inputs are provided for

redundancy. Users can check the LED status located in the front panel to see if

the power inputs are connected appropriately. If one of the power inputs fails,

the FAULT LED will light up in red if the power failure alarm is enabled.

NOTE The VPort 461 series supports power input specifications of 12-32

VDC for 12/24 VDC power input, or 18-30 VAC for 24 VAC

power input (note that this is different from Moxa EDS switch’s

12-45 VDC power input).

Step 2: Connect the VPort 461 to a Network

The VPort 461 has two auto-sensing 10/100 Mbps RJ45 Ethernet ports for

network connectivity. Each has a LED indicator located aside for indicating the

10 Mbps or 100 Mbps Ethernet connections.

NOTE These two Ethernet port can be cascaded in daisy chain link, or

connected to two different switch ports for Ethernet port

redundancy. More than that, they are also switch ports, which

means you can connect a Ethernet device on one of them for saving

the one switch port in the field site.

Step 3: Connect the VPort 461 to cameras and an audio source

The VPort 461 has 1 VIDEO INPUT port. Use the BNC connector (1.0 Vpp,

75Ω) and coaxial cable to connect video cameras to the VPort to input analog

video signals.

The VPort 461 has one audio input and one audio output. A microphone or an

amplifier can be plugged directly into the AUDIO INPUT port, and a speaker

can be plugged into the AUDIO OUTPUT port.

NOTE One VIDEO LED is located on the VPort 461’s front panel to

indicate the video signal transmission status for video input. Check

the LED status to see if the video is working properly.

ATTENTION

A ground loop isolator is recommended to be used between the

camera and the VPort to avoid a sudden current, which is

generated by the electric potential difference between these two

device’s ground power, to burn out the VPort’s chips and boards.

- 7 -

Step 4: Connecting motorized PTZ cameras and serial devices

The VPort 461 has two RS-232/422/485 ports. One is a COM PORT with DB9

male connector, and the other is a PTZ PORT with 5-pin terminal block

connector. Both ports can be used for connecting PTZ control cables for

controlling PTZ cameras over the TCP/IP network.

In addition, the DB9 male COM PORT can also be used to connect general

serial devices, such as card readers, for transmitting serial data over a TCP/IP

network. This port can be used to connect serial devices to the VPort

461instead of a video camera.

To enable PTZ control, users should configure the PTZ control protocol in the

web-based manager.

NOTE The PTZ control protocol is not standardized. To use a particular

PTZ control protocol, the video server must support the driver for

that protocol. Currently, the VPort 461 supports PTZ control

protocol drivers for:

1. Pelco D

2. Pelco P

3. DynaColor DynaDome

4. Yokogawa (Fieldeye)

5. Cohu

If you need to use a protocol that is not on the list, contact the

manufacturer of the camera to get the PTZ control commands, and

then program its PTZ control using the VPort 461’s Custom

Camera function.

NOTE The VPort 461 comes with a PTZ driver upload function for

implementing new PTZ drivers. Please contact a Moxa sales

representative if you need assistance from Moxa’s R&D department

to create a new PTZ driver.

NOTE The “Transparent PTZ Control” function in the camera driver list is

used to transmit the PTZ control signal over a TCP/IP network to

the VPort D361 video decoder or PC (additional driver required).

The PTZ control panel or keyboard can directly control the PTZ

camera or device, eliminating the need for a PTZ camera driver and

allowing the use of PTZ cameras with the VPort encoder.

Step 5: Configure the VPort 461’s IP address

After powering on the VPort 461, wait a few seconds for the POST (Power On

Self Test) to run. The STAT LED turns green to indicate that the POST process

has completed. The IP address will be assigned when the 10/100 Mbps

NETWORK LED blinks. The IP address assigned after the POST is completed

depends on the network environment.

Network Environment with DHCP Server

In this case, the IP address of the VPort 461 is assigned by a DHCP Server.

Use the DHCP Server’s IP address table, or use the Moxa VPort utility to

determine the IP address that was assigned by the DHCP Server.

- 8 -

NOTE After powering on the VPort 461, wait a few seconds for the POST

(Power On Self Test) to run. The IP address will be assigned when

the 10/100 Mbps NETWORK LED blinks.

Using the Moxa VPort and EtherDevice Configurator Utility

(edscfgui.exe)

1. Run the edscfgui.exe program to search for the VPort and EDS switches.

After the Utility window opens, select or click on Broadcast Search, which

is located under the List Server menu, to initiate a search (note that you

can also click on Broadcast Search icon to initiate a search).

NOTE You may download the VPort and EtherDevice Configurator

software from Moxa’s website at www.moxa.com.

2. The Broadcast Search window will show a list of all switches and VPorts

located on the network. The progress of the search will also be indicated.

- 9 -

3. When the search has ended, the Model Name, MAC address, and IP

address of the EDS switches and VPorts will be listed in the Utility

window.

NOTE Broadcast Search can only search for devices connected to the

same LAN subnet as the VPort. If your devices are located on a

different LAN subnet, use the “Specify IP Address” function to

search for the device by keying in the IP address.

4. Double click the selected VPort, or use Internet Explorer to access the

VPort’s web-based manager (web console).

Network Environment without a DHCP Server

If your VPort 461 is connected to a network that does not have a DHCP server,

then you will need to configure the IP address manually. The default IP address

of the VPort 461 is 192.168.127.100 and the default subnet mask is

255.255.255.0. Note that you may need to change your computer’s IP address

and subnet mask so that the computer is on the same subnet as the VPort.

To change the IP address of the VPort manually, access the VPort’s web server,

and then navigate to the System Configuration Æ Network Æ General page

to configure the IP address and other network settings. Select the Use fixed IP

address checkbox to ensure that the IP address you assign is not deleted each

time the VPort is restarted.

Step 6: Log on to the VPort 461 web-based manager

Type the IP address in the web browser’s address input box and then press

enter.

- 10 -

Step 7: Install the ActiveX Control Plug-in

A security warning message will appear the first time you access the VPort’s

web-based manager. The message is related to installing the VPort AcitveX

Control component to your PC or notebook. Click on Yes to install this plug-in

to enable the ability to view video in the IE web browser.

NOTE For Windows XP SP2 or later operating systems, the ActiveX

Control component will be blocked for system security reasons. In

this case, the VPort’s security warning message window may not

appear. Users should unblock the ActiveX control function or

disable the security configuration to enable the installation of

VPort’s ActiveX Control component.

Step 8: Accessing the homepage of the VPort 461’s web-based manager

After installing the ActiveX Control component, the homepage of the VPort

461’s web-based manager will appear. Check the following items to make sure

the system was installed properly:

1. Video Images.

2. Audio Sound (make sure your PC’s or notebook’s sound is turned on).

3. Video Information.

Inhaltsverzeichnis

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies N Port Express Installations- und Benutzerhandbuch

Moxa Technologies

Moxa Technologies VPort 461A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 351 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCC-80I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 1400-G2 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1171I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio TCC-80I Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 464 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 364 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort D351 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21A IMC-21A Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio A52 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21A series Handbuch

Moxa Technologies

Moxa Technologies UPORT 1110 Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 2000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-90 Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-S Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 364 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCC-100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 451 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1100 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-S Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung