Moxa Technologies UPort 1400-G2 Series Bedienungsanleitung

P/N: 1802014000110

*1802014000110*

UPort™ 1400/1600-G2 Series

Quick Installation Guide

Version 1.0, October 2023

Technical Support Contact Information

www.moxa.com/support



- 2 -

Overview

Moxa’s USB-to-serial products provide a wide range of easy-to-use

solutions for adding Windows COM ports, macOS, and Linux tty ports

through the USB port of a computer. The UPort 1400/1600-G2 Series

comprises the following models:

4-port Models

UPort 1410-G2 RS-232 USB-to-serial converter 0 to 60°C

(32 to 140°F)

UPort 1450-G2

RS-232/422/485 USB-to-serial

converter

0 to 60°C

(32 to 140°F)

UPort 1450-G2-T

RS-232/422/485 USB-to-serial

converter

-40 to 75°C

(-40 to 167°F)

UPort 1450I-G2 RS-232/422/485 USB-to-serial

converter with isolation protection

0 to 60°C

(32 to 140°F)

UPort 1450I-G2-T

RS-232/422/485 USB-to-serial

converter with isolation protection

-40 to 75°C

(-40 to 167°F)

8-port Models

UPort 1610-8-G2

RS-232 USB-to-serial converter

0 to 60°C

(32 to 140°F)

UPort 1650-8-G2

RS-232/422/485 USB-to-serial

converter

0 to 60°C

(32 to 140°F)

UPort 1650-8-G2-T RS-232/422/485 USB-to-serial

converter

-40 to 75°C

(-40 to 167°F)

UPort 1650I-8-G2

RS-232/422/485 USB-to-serial

converter with isolation

protection

0 to 60°C

(32 to 140°F)

UPort 1650I-8-G2-T RS-232/422/485 USB-to-serial

converter with isolation

protection

-40 to 75°C

(-40 to 167°F)

UPort 1650-8-G2-

Hub

RS-232/422/485 USB-to-serial

converter, with 3 downstream

USB type-A connectors

0 to 60°C

(32 to 140°F)

WARNING

This unit is not intended for consumer use. It will only be

shipped to manufacturers or factories.

The DC source should come from a class external adapter

or a 12 to 48 VDC safety extra-low voltage (SELV) limited

power source (LPS) using a transfer device.

This unit should be installed or set up by a qualified service

person.

Package Checklist

After opening the box, verify that the package contains the following

items:

•1 UPort 1400/1600-G2 USB-to-serial converter

•1 USB cable with latch:

- 3 -

CBL-USB3-BA-G-120 for all models except for the UPort

1650-8-G2-Hub, 1.2 m, with hook and screw

CBL-USB3-BA-G-028 for the UPort 1650-8-G2-Hub, 28 cm,

with hook and screw

•100 to 240 VAC power adapter (only included for UPort 1650I-8-G2

and UPort 1650-8-G2-Hub models)

•Quick installation guide (printed)

•Warranty card (printed)

NOTE

Notify your sales representative if any of the above items

are

missing or damaged.

Accessories

Power Adapters

•PWR-12050-USJP-S1 (for all models except UPort 1650-8-G2-Hub)

•PWR-12300-WP-S2 (for UPort 1650-8-G2-Hub)

•PWR-12150-*-SA-T (for all -SA-T models; *: EU/USJP/CN/UK/AU)

WARNING

This product is intended to be supplied by an approved external

power source (UL listed/IEC 60950

-1/IEC 62368-1) which

output complies with ES1/SELV, PS2/LPS, output rating 12 to

48 VDC, 2.25 A minimum (by DC jack) or 5 VDC, 0.61 A

minimum (by USB port), ambient temperature 75°C minimum.

If further information or help is needed, please contact your

Moxa representative. If

a Class I power source is used, the

power cord should be connected to a socket outlet with an

earthing connection.

Cables

•CBL-USB3-BA-G-120: USB 3.2 Gen 1 cable with latch 1.2 M

•CBL-USB3-BA-G-028: USB 3.2 Gen 1 cable with latch 0.28 M

•CBL-USB3-BA-B-120: Standard USB 3.2 Gen 1 cable 1.2 M

DIN-rail Kits:

•DK-UP1400-G2 (for UPort 1400-G2 models)

•DK-UP1600-G2 (for UPort 1600-G2 models)

Wall-mounting Kits:

WK-UP400A-BOT-BK: Wall mounting for 4/8-port models

Rack-mounting Kits:

•RK-UP1600-G2: 1U tray Rack-mounting Kit

Adapters:

•LB-DB9F-G-01: Serial Loopback adapter

•ADP-RJ458P-DB9F: DB9F-to-RJ45 adapter

•Mini DB9F-to-TB: DB9F-to-TB adapter

Hardware Introduction

An example of the UPort 1650-8-G2-Hub front and back panel:

- 4 -

Front View

Back View

USB Cable Usage Guide

The new Moxa latch USB cable

comes with a latch on each side of

the Type

-A connector and a screw

on the Type

-B connector.

Plugging in the USB Cable Using Type A Connector

To plug in the USB cable to the host computer and secure it, do the

following:

Step 1: Press both latches on the

connector

Step 2: Plug the connector into the

USB slot

- 5 -

Removing the USB Cable

Step 1:

Press both latches on the

USB cable connector

hard

so that

they are pushed to the

maximum.

Step 2:

Unplug and pull out the

cable 90 degree

s horizontal to the

USB socket.

ATTENTION

Be c

autious when plugging in or out the latch connector.

When the cable is plugged into a host computer or pulled

out every time, always press both latches. Then, plug the

connector into the receptacle on your computer or vice

versa.

If the type A connector doesn’t come off smoothly, DO

NOT pull the cable out by force as it will deform the hook

on the connector, and you

may not be able to use the cable

again. Try again by pushing the latch hard and shake the

connector left to right gently.

NOTE

The latch cable is designed to lock to

most of the computer

USB sockets

; however, there may be some sockets that are

designed with

a slight marginal difference, which may cause

the latch not to lock to your computer USB sockets perfectly.

Plugging in a USB Cable to the Host Computer Using Type B

Connector

The screw on the side of type B connector is for fixing the cable firmly

to the UPort. Please remember to swivel the bolt after plugging in and

before pulling out the connector.

Step 1: Plug in type B connector.

Step 2: Swivel the bolt about five rounds.

- 6 -

Pulling out a USB cable from the host computer

Step 1: Swivel the bolt about five rounds until it is loose.

Step 2: Pulling out type B connector.

LED Indicators

The LED indicators on the front panel are used to display the status as

follows:

Function

Color

Definition

Ready

Red

Power is on and the system is not yet ready

Green

System is up and ready

Green blinks

Locate in action

Off

Unit is not powered or out of operation

Green blinks

Transmitting data

Off

No data is being transmitted, or the serial

device is not connected or out of operation

Orange blinks

Receiving data

Off No data is being received, or the serial

device is not connected or out of operation

Serial Port Pin Assignments

The serial ports on the UPort 1400/1600-G2 have DB9 male connectors.

Refer to the following table below for the RS-232 and RS-422/485 pin

assignments.

Serial Port

(Male DB9)

Pin RS-232

RS-422/

RS-485-4W

RS-485-2W

DCD

TxD-(A)

–

RXD

TxD+(B)

–

TXD

RxD+(B)

Data+(B)

DTR

RxD-(A)

Data-(A)

GND

DSR

–

RTS

–

CTS

–

NOTE

For the UPort with DB9 male serial ports, you may refer to the

Serial Port Pin Assignments

section to loop back pin 2 and pin 3

for the RS

-232 interface to carry out a self-test on the device.

You may refer to

Communication Testing in the Software

Installation

sections in this document for how to use the

loopback connector in the box to perform the communication

test.

- 7 -

Adjustable Pull High/low Resistors for the RS-485 Port

The UPort uses DIP switches to set the pull high/low resistor values for

each serial port.

To set the pull high/low resistors to 150 KΩ, make sure both SW 1

and SW 2 switches are in the OFF position. This is the default setting.

To set the pull high/low resistors to 1 KΩ, make sure both SW 1

and SW 2 switches are in the ON position.

To set the termination on, SW 3 should be set to the ON position.

Switch

Pull High

Pull Low

Termination

–

1 KΩ

120 Ω

–

OFF

150 KΩ

–

ATTENTION

Do not use the 1

-kΩ setting on the UPorts when using an RS-

232 interface. Doing so will degrade the

RS-232 signals and

shorten the maximum allowed communication distance.

UPort 1400-G2 DIP Switches Location

UPort 1600-G2 DIP Switches Location

- 8 -

Software Installation

To install the UPort driver, please follow the installation procedure

described in the Mounting the UPort 1400/1600-G2 section. UPort

converters can be connected to any upstream type A USB port that is

on the PC host or an upstream hub. UPort converters are hot-

pluggable, and therefore there is no need to power down your

computer prior to installation.

When the UPort is successfully installed, use the operating system’s

device manager to check and/or change the port settings. In Windows,

the new COM port will be listed under Ports (COM & LPT).

Installing the Windows Driver

Download and run the Setup program from the UPort’s product

page and follow the installation steps.

A few things to note:

1. We recommend also installing companion utilities for future use.

For an introduction of the utility, refer to the User Manual.

2. After the driver is successfully installed, connect the UPort to your

computer. Then, click Scan to review the installation results and

confirm that the UPort is connected to your computer.

- 9 -

3. Check Launch Windows Driver Manager to configure the UPort

after the setup is completed.

4. If you have installed ViewCOM, you can mouse over the

ViewCOM icon in the system tray to see COM port information.

The right-click context menu has the shortcut to Windows

Device Manager and Auto Startup utilities if needed.

For configuration details, check COM Port Configuration section in the

User Manual.

Installing the Linux Driver

Run the following commands from the Linux prompt:

# CD /moxa

# tar xvfz moxa-uport-1200-1400-1600-series-linux-kernel-

[kernel version]-driver-v[driver version].tgz

Find the Makefile file in /moxa/mxuport and run the commands:

# make install

# modprobe mxuport

For further information, refer to the User Manual or the readme.txt

that comes with the driver package.

- 10 -

Installing the Linux Driver for Arm-based Platforms

Please refer to the Tech Note: UPort Driver Arm-based Platform

Porting Guide on the product page or the readme.txt that comes

with the driver package.

Installing the macOS Driver

For macOS 10.12 and later, follow the steps below to install the driver:

1. Enter the recovery mode.

2. Disable System Integrity Protection (SIP) by running the csrutil

disable command from the terminal.

3. Return to the normal mode.

4. Launch the UPort driver installer and complete the installation

procedure.

5. Reenter the recovery mode.

6. Enable System Integrity Protection (SIP) by running the csrutil

enable command from the terminal.

7. Return to the normal mode.

For detailed instructions, please refer to the User Manual on the product

page or the readme.txt that comes with the driver package.

Communication Testing

There are Moxa companion utilities for serial communication testing.

For this purpose, you may use PComm Terminal. For other useful

utilities, please refer to the UPort’s User Manual for an introduction.

Mounting the UPort 1400/1600-G2

UPort 1400-G2

Dimensions

Unit = mm (inches)

Wall Mounting

The mounting kit is 2 mm in height, and

the two centers of the mounting kit on each

plate are 208

mm (8.19 in).

Andere Handbücher für UPort 1400-G2 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies VPort 364 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21A IMC-21A Bedienungsanleitung

Moxa Technologies

Moxa Technologies NE-4100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1171I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1110 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21GA Handbuch

Moxa Technologies

Moxa Technologies ME51 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21GA-T Handbuch

Moxa Technologies

Moxa Technologies TCF-141-S Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 351 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 1400-G2 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-M-ST Bedienungsanleitung

Moxa Technologies

Moxa Technologies PTC-101 Series Handbuch

Moxa Technologies

Moxa Technologies ICF-1180I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5100A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort D351 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 2210 Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-S Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 25 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 2141 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5110A Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCC-80I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MIINEPORT E1 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung