Moxa Technologies VPort D351 Bedienungsanleitung

- 1 -

Moxa Industrial Video Decoder

VPort D351

Quick Installation Guide

First Edition, November 2007

Moxa Networking Co., Ltd.

Tel: +886-2-8919-1230

Fax: +886-2-8919-1231

www.moxa.com

support@moxa.com (Worldwide)

support@usa.moxa.com (The Americas)

P/N:1802003511010

- 2 -

Overview

The VPort D351 is a 1-channel video decoder used to decode MJPEG/MPEG4

video streams (received from a VPort series video encoder and IP camera) back

to an analog video signal. The analog video signal can be sent to legacy CCTV

devices, such as monitors, multiplexer, and matrix switches, allowing these to

retain their original purpose in the CCTV system. In addition, bi-directional

audio enables ready-to-use voice over IP communication between the video

encoder and decoder.

In order to make camera monitoring more convenient for large CCTV systems,

the VPort D351 can be set up to switch between different video sources

manually, or automatically within a given time interval. A maximum of 64

video sources can be added to the switching camera list. In addition, users can

use the 2 DIs located on the top panel to build 2 control buttons for up and

down video source selection.

Package Checklist

The Moxa VPort D351 is shipped with the items listed below. If any of these

items is missing or damaged, please contact your customer service

representative for assistance.

y1 × VPort D351

y1 × 6-pin terminal block for one power input and 2 DIs

y1 x 8-pin terminal block for the second power input and 2 relay outputs

y1 × 5-pin terminal block for RS-232/422/RS-485 PTZ control port

yQuick Installation Guide (printed)

yDocument & Software CD (includes User’s Manual, Quick Installation

Guide, MOXA IVN Solution Datasheet, and Utility software)

yWarranty Card

NOTE The VPort Video encoders mentioned here do not include the

VPort 2110, VPort 2140, VPort 2141, VPort 2310, and VPort.

3310.

NOTE Check the model name on the VPort’s side label to determine if the

model name is correct for your order.

NOTE This product must be installed in compliance with your local laws

and regulations.

Features

High Performance Audio/Video Networking Solution

y1-channel video output for analog NTSC/ PAL video signals

y1 audio input and 1 audio output for 2-way voice communication

y1 auto-sensing 10/100BaseT(X) Ethernet port

yTCP, UDP, HTTP, and multicast network transmission modes

- 3 -

y1 RS-232/422/485 PTZ port with serial-to-Ethernet Real COM mode for

remote PTZ control with exiting legacy PTZ control device (PTZ control

driver NOT required)

yCapability to decode different video stream resolutions from video encoder

with maximum 540 TVL lines

yMaximum of 64 video sources can be set up as the decode video source

yCan manually select the video source, or setup automatic scanning for

video sources

ySupports switching the video source using the 2 digital inputs

yBuilt-in web server, and RS-232 consoles for remote access and

configuration

ySupports SNMP (V1/V2C/V3) for network system integration and

management

ySupports OSD (On-Screen Display)

yUPnP and IP filtering supported

Industrial Rugged Design

y2 12/24 VDC and 24 VAC redundant power inputs with LED indicators

y35 mm DIN-Rail mounting or panel mounting (optional kit required)

yIP30 form factor protection

yCE, FCC, UL certified

Intelligent Alarm Triggering Capability

yEquipped with 2 DIs and 2 relays (DO) for external sensors and alarms

yCan be set up to switch automatically to a specific video source in

response to an event triggered by the VPort encoder

ySupports SMTP for system or alarm message transmission

- 4 -

Panel Layout of VPort D351

VPort D351

Front Panel View

Top Panel View

Rear Panel View

V1, V2: 12-32 VDC

12-30 VAC

RS-232

CONSOLE

VPort D351

1. Grounding screw

2. RS-232 console port

3. Hardware reset button

4. 6-pin terminal block for DI 1,

DI 2, power input 2 (PWR2)

5. 8-pin terminal block for Relay 1,

Relay 2, power input 1 (PWR1)

6. Heat dissipation orifices

7. LEDs for STAT, PWR1, PWR2,

FAULT

8. AUDIO OUTPUT port for external

speaker

9. AUDIO INPUT port for mic-in and

line-in connection

10. 5-pin terminal block for

RS-232/422/ 485 connection

11. BNC port for analog video output

12. RJ45 10/100BaseTX Ethernet

Port with 10 Mbps, 100 Mbps

LEDs

13. Model name

14. Screw hole for wall mounting kit

15. DIN-Rail mounting kit

- 5 -

First-Time Installation and

Configuration

Before installing the VPort D351, check to make sure that all items in the

package checklist are present. In addition, you will need access to a notebook

computer or PC equipped with an Ethernet port.

Step 1: Select the Power Source

The VPort D351 can be powered by a 12 to 32 VDC power input, or an 18 to

30 VAC power input. Two power inputs are provided for redundancy. Users

can check the LED status located on the front panel to see if the power inputs

are connected appropriately. If one of the power inputs fails, the FAULT LED

will light up in red.

NOTE The VPort D351 supports 12-32 VDC for a 12/24 VDC power

input, or 18-30 VAC for a 24 VAC power input. This differs from

the 12-45 VDC power input supported by Moxa’s EDS series of

Ethernet switches.

Step 2: Connect the VPort D351 to a network

The VPort D351 has an auto-sensing 10/100 Mbps RJ45 Ethernet port for

network connectivity. LEDs to indicate 10/100 Mpbs data transmission are

provided for both the RJ45 port and fiber optic ports.

Step 3: Connect the VPort D351 to an audio source (if required)

The VPort D351 supports 1 AUDIO INPUT and 1 AUDIO OUTPUT. A

microphone or an amplifier can be plugged directly into the AUDIO INPUT

port; a speaker can be plugged into the AUDIO OUTPUT port.

Step 4: Connect the VPort D351 to a video output source

The VPort D351 supports 1 VIDIO OUTPUT for transmitting analog video.

Connect the video output source, such as CCTV monitor or switch, to the BNC

connector to show the analog video.

Step 5: Connect the VPort D351 to a control panel or keyboard to control

the motorized PTZ Camera/Device (if required)

If a motorized PTZ camera or device is used at the VPort encoder site, users

can connect the PTZ control panel or keyboard to the VPort D351’s PTZ port

to control the motorized PTZ camera or device directly once the connection

between the VPort D351 and the VPort encoder is ready. The PTZ port uses a

5-pin terminal block for the RS-232/422/485 serial connection. The pin

assignments are shown in the following table.

PIN RS-422/485 RS-232

1 GND Ground GND Ground

2 R- Rx- --- N/A

3 R+ Rx+ RxD RxD

4 T-\D- Tx-/ Data- --- N/A

5 T+\D+ Tx+/ Data+ TxD TxD

Use the web-based manager to configure the PTZ control protocol.

- 6 -

NOTE The VPort D351 supports Transparent PTZ control, which means

that the VPort D351 can connect directly to the PTZ control panel

or keyboard to control the remote PTZ camera connected to the

VPort encoder. Since the PTZ control protocol is not standardized,

the PTZ control panel and keyboard must support the control of

PTZ cameras.

NOTE Currently, VPort encoders support PTZ control protocol drivers

for: 1. Pelco D

2. Pelco P

3. DynaColor DynaDome

In addition, there is an item named “Transparent PTZ Control” in

the camera driver list. This is used to transmit the PTZ control

signal over the TCP/IP network to the VPort D351 video decoder,

so that the PTZ control panel or keyboard can directly control the

PTZ camera or device. Using this method eliminates the need for a

PTZ camera driver. In addition, you will be able to use any PTZ

camera with your VPort encoders.

Step 6: Configure the VPort D351’s IP address

After powering on the VPort D351, wait a few seconds for the POST (Power

On Self Test) to run. The POST process is complete once the STAT LED turns

green. The IP address will be assigned when the 10 or 100 Mbps NETWORK

LED blinks. The value of the IP address that is assigned is based on the

network environment.

Network Environment with DHCP Server

When a DHCP server is present, the IP address of the VPort D351 is assigned

by the DHCP server. Use the DHCP server’s IP address table, or use the Moxa

VPort and Ether Device Configurator utility to determine the IP address that

was assigned by the DHCP server.

NOTE After powering on the VPort D351, wait a few seconds for the

POST (Power On Self Test) to run. The IP address will be assigned

when the 10 or 100 Mbps NETWORK LED blinks.

Using Moxa VPort and EtherDevice Configurator Utility (edscfgui.exe)

1. Run the edscfgui.exe program to search for VPorts and EDS switches.

After the Utility window opens, select or click on Broadcast Search under

the List Server menu, or click on the Broadcast Search icon to

initiate a search.

NOTE You may download the VPort and EtherDevice Configurator

software from Moxa’s website at www.moxa.com.

- 7 -

2. The Broadcast Search window will show a list of all switches and VPorts

located on the network. The progress of the search will also be indicated.

3. When the search has ended, the Model Name, MAC address, and IP

address of the EDS switches and VPorts will be listed in the Utility

window.

NOTE Broadcast Search can only search for devices connected to the

same LAN domain as the VPort. If your devices are located on a

different LAN domain, use the Specify IP Address function to

search for the device by keying in the IP address.

4. Double click the selected VPort, or use the IE web browser to access the

VPort’s web-based manager (web console).

- 8 -

Network Environment without DHCP Server

If your VPort D351 is connected to a network that does not have a DHCP

server, you will need to configure the IP address manually. The default IP

address of the VPort D351 is 192.168.127.100 and the default subnet mask is

255.255.255.0. Note that you may need to change your computer’s IP address

and subnet mask so that the computer is on the same subnet as the VPort.

To change the IP address of the VPort manually, access the VPort’s web server,

and then navigate to the System Configuration ÆNetwork ÆGeneral page

to configure the IP address and other network settings. Check the Use fixed IP

address to ensure that the IP address you assign is not deleted each time the

VPort is restarted.

Step 7: Accessing the VPort D351 Web-based Manager

1. Type the IP address in the web browser’s address input box and then press

enter to connect to the homepage of the VPort D351’s web-based manager.

NOTE Once the VPort D351’s homepage opens, administrators can go to

System Configuration ÆSystem ÆAccount to set up the

administrator’s password. After that, an authentication window will

open to request that the administrator input the account name:

admin, and the new password.

Step 8: Accessing VPort’s System Configuration

Click on System Configuration to access the overview of the system

configuration to change the configuration. Model Name, Server Name, IP

Address, MAC Address, Firmware Version, and LED Status appear in the

green bar near the top of the page. Use this information to check the system

information and installation. For details of each configuration, check the User’s

Manual on the software CD.

- 9 -

Mounting Dimensions (unit=mm)

135

86.14

66.8

9.75

66.54

134

30.05

46 32

18.2

32.1

18.2

91.55

40 45.27

52.85 105

Din-Rail

Panel Mount Kit

- 10 -

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be attached to the

back panel of the VPort D351 when you take it out of the box. If you need to

reattach the DIN-Rail attachment plate to the VPort D351, make sure the stiff

metal spring is situated towards the top, as shown in the figures below.

STEP 1:

Insert the top of the DIN-Rail into the

slot just below the stiff metal spring.

STEP 2:

The DIN-Rail attachment unit will snap

into place as shown below.

metal

spring

DIN-Rail

metal

spring

DIN-Rail

To remove the VPort D351 from the DIN-Rail, simply reverse Steps 1 and 2

above.

Wall Mounting (Optional)

For some applications, you will find it convenient to mount the VPort D351 on

the wall, as illustrated below.

STEP 1:

Remove the aluminum DIN-Rail attachment plate from the VPort D351, and

then attach the wall mount plates, as shown in the diagrams below.

⇒

Top

plate

Bottom

plate

STEP 2:

Mounting the VPort D351 on the wall requires 4 screws. Use

the VPort D351, with wall mount plates attached, as a guide

to mark the correct locations of the 4 screws. The heads of

the screws should be less than 6.0 mm in diameter, and the

shafts should be less than 3.5 mm in diameter, as shown in

the figure at the right.

Do not screw the screws in all the way—leave a space of

about 2 mm to allow room for sliding the wall mount panel

between the wall and the screws.

6.0 mm

3.5 mm

Inhaltsverzeichnis

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies ICF-1171I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5110A Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCC-80I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1200 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-RM Series Handbuch

Moxa Technologies

Moxa Technologies VPort 364A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-101G Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 351 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-101 Series Handbuch

Moxa Technologies

Moxa Technologies TCC-100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 251 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-90 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 451 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1170I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 254 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ME50-M-SC Bedienungsanleitung

Moxa Technologies

Moxa Technologies ME51 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 2000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-101 Series Handbuch

Moxa Technologies

Moxa Technologies UPort 1400-G2 Series Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung