Moxa Technologies VPort 364 Series Bedienungsanleitung

P/N: 1802003640010

VPort 364 Series

Quick Installation Guide

Moxa Industrial Video Encoder

First Edition, January 2011

- 2 -

Overview

The VPort 364 is a 4-channel industrial video encoder that supports the

H.264 video compression algorithm, which provides the best video quality

on the market while requiring less bandwidth compared to other video

compression standards. In addition, the VPort 364 supports simultaneous

dual video streams with different formats: H.264 and MJPEG. The two

video streams can be used for different purposes, such as viewing,

recording, or analysis. In addition, the rugged industrial design with -40

to 75°C operating temperature, built-in fiber Ethernet ports, IP30-rated

form factor, and industrial certifications, make the VPort 364 highly

suitable for use in harsh environments.

Package Checklist

The VPort 364 ships with the following items:

•VPort 364.

•Two 5-pin terminal blocks for 2 power inputs and 2 relay outputs.

•8-pin terminal block for 4 DIs (Digital Inputs).

•5-pin terminal block for the RS-232/422/RS-485 PTZ control port.

•Quick installation guide.

•Documentation & Software CD

•Warranty Card.

Note: If any of these items are missing or damaged, please contact your

customer service representative for assistance.

NOTE This product must be installed in compliance with your local laws

and regulations.

Features

High Performance Audio-Video Networking Solution

•Compatible with NTSC/PAL analog video cameras

•H.264 and MJPEG video compression standards

•Dual simultaneous video streams (1 H.264 and 1 MJPEG)

•Lower latency, under 200 ms

•4 BNC video inputs

•Single video stream up to 30 frames/sec in Full D1 (720 x 480)

resolution in NTSC, and 25 frames/ sec in Full D1 (720 x 576)

resolution in PAL

•Select between Full D1/ 4CIF/ VGA/ CIF/ QCIF resolutions

•1 audio input and 1 audio output for 2-way voice communication

•TCP, UDP, and HTTP network transmission modes

•Modbus/TCP for easy communication with SCADA systems

•Standard RTSP (Real-time streaming protocol) for easy integration

•DynaStream™ for automatic frame rate adjustment to control IP

video traffic

•Multicast (IGMP) protocols for efficient network transmission

•QoS (TOS) for priority transmission

•SNMP V1/V2c/V3 for network management

•Built-in web server and RS-232 console for remote access and

configuration

•One auto-sensing 10/100BaseT(X) or 100BaseFX (SC connector)

Ethernet port

- 3 -

•8 output video streams and 8 client connections

•50 multicast clients for receiving multicast video streams

•Multicast push for all the clients

•Video quality in CBR (constant bit rate) or VBR (variable bit rate)

•Supports one RS-232/RS-422/RS-485 5-pin PTZ port for controlling

a PTZ (PAN/TILT/ZOOM) motorized camera via a TCP/IP network

•UPnP and IP filtering

Rugged Industrial Design

•Two 12/24 VDC and 24 VAC redundant power inputs with LED

indicators

•-40 to 75°C operating temperature for harsh industrial environments

(“T” models)

•35 mm DIN-Rail mounting or panel mounting installation

(with optional accessory)

•IP30-rated form factor

•CE, FCC, and UL508(pending)

Intelligent Alarm Trigger Capability

•Supports system alarms, including power failure and network link

•Supports event alarms, including video motion detection (VMD),

video loss, digital input, and CGI event

•Equipped with 4 DIs and 2 relays (DO) for external sensors and

alarms.

•Pre, trigger, and post alarm snapshot images provided.

•Supports sequential snapshot images

•Messages with snapshot images can be sent via FTP and email.

•Capable of setting an alarm schedule

Video Management and Control

•Free Moxa VPort SDK Plus (software development kits) supported

with flexible interface and sample codes for customized application or

system integration.

•Moxa SoftNVR-IA IP surveillance software supported for the video

recording and management solution.

NOTE If you are interested in the VPort SDK PLUS, visit

Moxa’s website

(www.moxa.com) to download the software, or contact a Moxa

sales representative for more information.

NOTE If you are interested in SoftNVR-IA IP surveillance software, visit

Moxa’s website (www.moxa.com) to download the trial version.

- 4 -

VPort 364 Panel Layout

1. RS-232 console port

2. Hardware reset button

3. 8-pin terminal block for DI 1 to DI 4

4. 5-pin terminal block for Relay 2 and

power input 2 (PWR2)

5. Grounding screw

6. 5-pin terminal block for Relay 1 and

power input 2 (PWR1)

7. Heat dissipation orifices

8. LEDs for STAT, PWR1, PWR2, and

FAULT

9. LEDs for V1 to V4

10. AUDIO OUTPUT port for external

speakers

11. AUDIO INPUT port for mic-in and

line-in connection

12. 4 BNC connector for V1 to V4 video

inputs

13. RJ45 10/100BaseTX Ethernet port

with 10/100 Mbps LED

14. 100BaseFX fiber optic port with 100

Mbps LED

15. RS-232/422/485 PTZ port with 5-pin

terminal block for PTZ camera control

16. Model name

17. Screw hole for wall mounting

18. Screw hole for DIN-Rail mounting

- 5 -

First-Time Installation and Configuration

Before installing the VPort 364, check to make sure that all the items in

the package checklist are in the box. In addition, you will need access to

a notebook computer or PC equipped with an Ethernet port.

Step 1: Select the Power Source

The VPort 364 can be powered by a DC power input from 12 to 32 VDC, or

an AC power input from 18 to 30 VAC. Two power inputs are provided for

redundancy. Users can check the LED status located in the front panel to

see if the power inputs are connected appropriately. If one of the power

inputs fails, the FAULT LED will light up in red if the power failure alarm is

enabled.

NOTE The VPort 364 series supports power input specifications of 12-

VDC for 12/24 VDC power input, or 18-

30 VAC for 24 VAC power

input (note that this is different from Moxa EDS switch’s 12-45

VDC power input).

Step 2: Connect the VPort 364 to a Network

The VPort 364 has one auto-sensing 10/100 Mbps RJ45 Ethernet or 100

Mbps fiber optic port (multi mode or single mode). An LED indicator

located on the side of each port indicates a 10 Mbps or 100 Mbps Ethernet

connection.

Step 3: Connect the VPort 364 to cameras and an audio source

The VPort 364 has four VIDEO INPUT ports (V1, V2, V3, and V4). Use the

BNC connector (1.0 Vpp, 75Ω) and coaxial cable to connect video

cameras to the VPort to input analog video signals.

The VPort 364 has one audio input and one audio output. A microphone or

an amplifier can be plugged directly into the AUDIO INPUT port, and a

speaker can be plugged into the AUDIO OUTPUT port.

NOTE The four LEDs (V1, V2, V3, and V4) located on the VPort 364’s

front panel indicate the video signal transmission status for vid

inputs. You may refer to these LEDs to verify video signal status.

ATTENTION

A ground loop isolator is recommended to be used between the

camera and the VPort to avoid a sudden current, which is

generated by the electric potential difference between these two

device’s ground power, to burn out the VPort’s chips and boards.

Step 4: Connecting motorized PTZ cameras and serial devices

The VPort 364 has an RS-232/422/485 PTZ port with 5-pin terminal block

connector. It can be used for connecting PTZ control cables for controlling

PTZ cameras over the TCP/IP network.

To enable PTZ control, users should configure the PTZ control protocol in

the web-based manager (web console).

- 6 -

NOTE The PTZ control protocol is not standardiz

ed. To use a particular

PTZ control protocol, the video server must support the driver for

that protocol. Currently, the VPort 364 supports PTZ control

protocol drivers for:

1. Pelco D

2. Pelco P

3. DynaColor DynaDome

4. Cohu

If you need to use a protocol that is not on the list, contact the

manufacturer of the camera to get the PTZ control commands,

and then program its PTZ control using the VPort 364’s Custom

Camera function.

NOTE The VPort 364 comes with a PTZ driver upload function for

implementing new PTZ drivers. Please contact a Moxa sales

representative if you need assistance from Moxa’s R&D

department to create a new PTZ driver.

NOTE

The “Transparent PTZ Control” function in the camera driver list is

used to transmit the PTZ control signal over a TCP/IP n

etwork to

the VPort D361 video decoder or PC (additional driver required).

The PTZ control panel or keyboard can directly control the PTZ

camera or device, eliminating the need for a PTZ camera driver

and allowing the use of PTZ cameras with the VPort encoder.

Step 5: Configure the VPort 364’s IP address

After powering on the VPort 364, wait a few seconds for the POST (Power

On Self Test) to run. The STAT LED turns green to indicate that the POST

process has completed. The IP address will be assigned when the 10/100

Mbps NETWORK LED blinks. The IP address assigned after the POST is

completed depends on the network environment.

Network Environment with DHCP Server

In this case, the IP address of the VPort 364 is assigned by a DHCP Server.

Use the DHCP Server’s IP address table, or use the Moxa utility to

determine the IP address that was assigned by the DHCP Server.

NOTE After powering on the VPort 364

, wait a few seconds for the POST

(Power On Self Test) to run. The IP address will be assigned when

the 10/100 Mbps NETWORK LED blinks.

Using the Moxa VPort and EtherDevice Configurator Utility

(edscfgui.exe)

1. Run the edscfgui.exe program to search for the VPort IP video

products and EDS switches. After the Utility window opens, select or

click on Broadcast Search, which is located under the List Server

menu, to initiate a search (note that you can also click on Broadcast

Search icon to initiate a search).

NOTE You may download the VPort and EtherDevice Configurator

software from Moxa’s website at www.moxa.com.

- 7 -

2. The Broadcast Search window will show a list of all switches and

VPorts located on the network. The progress of the search will also

be indicated.

3. When the search has ended, the Model Name, MAC address, and IP

address of the EDS switches and VPorts will be listed in the Utility

window.

- 8 -

NOTE Broadcast Search can only search for devices connected to the

same LAN subnet as the VPort. If your devices are located on a

different LAN subnet, use the “Specify IP Address” function to

search for the device by keying in the IP address.

4. Double click the selected VPort, or use Internet Explorer to access

the VPort’s web-based manager (web console).

Network Environment without a DHCP Server

If your VPort 364 is connected to a network that does not have a DHCP

server, then you will need to configure the IP address manually. The

default IP address of the VPort 364 is 192.168.127.100 and the default

subnet mask is 255.255.255.0. Note that you may need to change your

computer’s IP address and subnet mask so that the computer is on the

same subnet as the VPort.

To change the IP address of the VPort manually, access the VPort’s web

server, and then navigate to the System Configuration Network 

General page to configure the IP address and other network settings.

Select the Use fixed IP address checkbox to ensure that the IP address

you assign is not deleted each time the VPort is restarted.

Step 6: Log on to the VPort 364 web-based manager (web

console)

Type the IP address in the web browser’s address input box and then

press enter.

Step 7: Install the ActiveX Control Plug-in

A security warning message will appear the first time you access the

VPort’s web-based manager. The message is related to installing the

VPort ActiveX Control component to your PC or notebook. Click on Yes to

install this plug-in to enable the ability to view video in the IE web

browser.

- 9 -

NOTE For Windows XP SP2 or later operating systems, the ActiveX

Control component will be blocked for system security reasons.

In this case, the VPort’s security warning message window may

not appear. Users should unblock the ActiveX control function or

disable the security configuration to enable the installation of

VPort’s ActiveX Control component.

Step 8: Accessing the homepage of the VPort 364’s web-based

manager

After installing the ActiveX Control component, the homepage of the

VPort 364’s web-based manager will appear. Check the following items to

make sure the system was installed properly:

1. Video Images.

2. Audio Sound (make sure your PC’s or notebook’s sound is turned

on).

3. Video Information.

Step 9: Accessing the VPort’s System Configuration

Click on System Configuration to access the overview of the system

configuration to change the configuration. Model Name, Server Name, IP

Address, MAC Address, Firmware Version, and LED Status appear in the

green bar near the top of the page. Use this information to check the

system information and installation.

For details of each configuration, check the User’s Manual on the software

CD.

- 10 -

NOTE After accessing the VPort 364’s web-based manager,

administrators should access System configuration > System >

Account to set up the administrator’s password and enable the

authentication function. The administrator account name is

admin. An authentication window will pop up requesting the

account name and password each time the VPort 364 is accessed.

Mounting Dimensions (unit = mm)

Andere Handbücher für VPort 364 Series

Inhaltsverzeichnis

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies NPort 5410 Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-S Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1180I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 461A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-S Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-101G Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 351 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 354 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21GA Handbuch

Moxa Technologies

Moxa Technologies VPort 254 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 1250I Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCC-120 Handbuch

Moxa Technologies

Moxa Technologies VPort 451 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1200 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21A series Handbuch

Moxa Technologies

Moxa Technologies VPort 351 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-P101 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1170I-M-ST Bedienungsanleitung

Moxa Technologies

Moxa Technologies PTC-101-M12 Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort D351 Bedienungsanleitung

Moxa Technologies

Moxa Technologies A50 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-101 Series Handbuch

Moxa Technologies

Moxa Technologies TCF-142-S-ST-RM Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung