MRC STE-TIN Bedienungsanleitung

Operation Manual

STE-TIN/TAN

Hagavish st. Israel 58817 Tel: 972 3 5595252, Fax: 972 3 5594529

[email protected]

Thank you for choosing this Steam Sterilizer.

Please read the instructions manual carefully in order to install the

equipment and operate the equipment in an efficient manner.

TABLE OF CONTENTS

1.GENERAL ------------------------------------------------------------ 1

2.TECHNICAL PARAMETER ---------------------------------------- 2

3.PACKING CONTENT ----------------------------------------------- 3

4.INSTALLATION ---------------------------------------------------- 4

5.OPERATION ---------------------------------------------------------- 5

5.1 READY ------------------------------------------------------------- 5

5.2 PREPARE THE MATERIAL TO BE STERILIZED -- 6

5.3 SELECTING THE STERILIZATION PROGRAM -------------- 7

5.4 RUNNING THE STERILIZATION PROGRAM ----------------- 8

5.5 TEST PROGRAMS -------------------------------------------------11

6. ADVANCED SETTING -------------------------------------------- 12

7. MAINTENANCE ---------------------------------------------------- 17

8. TRANSPORT AND STORAGE ------------------------------------ 20

9. ERROR CODES ----------------------------------------------------- 21

10. SAFETY DEVICES ------------------------------------------------ 22

APPENDIX

1. CHARACTERISTICS OF THE FEEDING WATER -------------- 23

2. DIAGRAMS OF THE STERILIZATION PROGRAMS --- 24

3. ELECTRICAL DRAWING ----------------------------------------- 31

4. HYDRAULIC DRAWING ----------------------------------------- 33

--------

------

Instructions manual

This sterilizer described in this manual is intended for the sterilization of

re-useable surgical instruments and material.

It operates automatically with 134 and 121 sterilization temperatures.

It has been produced in accordance with the EN 13060.

℃℃

1 General

1 Distilled water tank

2 LCD screen

3 Control panel

4 Main switch

5 Drain connector of distilled water tank

6 Door handle

7 Drain connector of used water tank

8 USB port (optional)

9 Printer port

10 Printer power

11 Bacteriological filter

12 Safety valve

13 Condenser ventilation

14 Circuit breaker

15 Power supply cord

16 Rating plate

In order to proper use the sterilizer, please be sure to read the

warning and attention carefully for safety.

Security Notice

This symbol is grounding protection inside the machine.

HOT SURFACE.

This symbol is visible on the front of the panel after open the door.

Important safety information.

This symbol is used to draw the attention of the reader to particularly

important notions for operator safety.

2 Technical Parameter

Chamber

Rated Voltage

Main Fuses

Nominal power (CLASS B)

Sterilization Temperature

Capacity of the distilled

water tank

Operation temperature

Outside size

Net weight CLASS B)（

Noise

Relative Humidity

Atmospheric pressure

Item

Φ230mmX360mm

Φ200mmX360mm

AC220V-240V(AC110V-130V), 50-60Hz

F16A/250V(F25A/250V for 110V)

2000VA

121 /134

℃℃

Approx 2.5L (water at level MAX)

Approx 0.5L (water at level MIN)

5-40

℃

445mm(width)X 410mm(height)X 605mm(depth)

76kPa -106kPa

max. 80%, non condensing

<70dB

41kg 45kg

Nominal power (CLASS N)

1900VA

Net weight CLASS N)（

39kg 43kg

Instructions manual

3 Packing Content

Quantity

Item

No.

Instrument tray

Instrument tray rack

Instrument tray handle

Door adjustment tool

Draining hose

Instructions manual

1Steam sterilizer

Door seal

4 Installation

* There must leaves 10cm gap around sterilizer, and 20cm on top side. the

clearance required for the movement of the door leave an at least

350mm fan-shaped space in front of the door.

* The place which sterilizer located must be ventilated, make sure that the

radiator not being jammed.

* The sterilizer should be placed on a level worktable.

* Don't cover or block the door, ventilation or radiation openings on the

sterilizer.

* Don't place the sterilizer near a sink or in a location where it is likely to

be splashed.

* Keep away from all sources of heat.

：

Instructions manual

605

Distilled water tank is lacking of water.

Distilled water tank is full

Used water tank is full.

Door locked

information output to USB port

Printer connect

Notice: Before using the sterilizer at the first start-up or any time the

icon blink, it is necessary to fill the distilled water tank

with distilled water.

5.1 Ready

5.1.1 Open the door and take out all the instrument tray and other

accessories inside, unpack and clean them.

5.1.2 Connect the power, and connect the printer (See 6.5)

5.1.3 Power on

The switch is located underneath the control panel

on the front side of the machine .

After switching on, the machine turns on the LCD .

Then it will show the door position, water level,

working program, date, time and etc. .

The machine will alert by beep sounds if there are

problems.

5 Operation

Program

Alarm code

process curve

Temperature

Pressure

Setting

Time

Date

5.1.4 Filling the distilled water

Open the top lid, and fill the tank with distilled water by cup or tank.

When you hear a beep signal, it means the water level exceeds the

max. level. The will be displayed. Please stop filling immediately.

5.2 Preparing the material to be sterilized

To get the better effectiveness of the sterilization process and to preserve

the material in time, follow the indications below reported.

* Arrange the tools of different metal (stainless steel, moderate steel,

aluminum, etc.) on different trays or however well separate between them;

* In case of not stainless steel tools, interpose a sterilization paper napkin or

muslin cloth between tray and tool, avoiding direct contacts between the

two different materials;

* Verify all the tools are sterilized in open position;

* Arrange the containers (glasses, cups, test-tubes, etc.) on one side or

inverted position, avoiding possible water stagnation;

* Don't overload the trays over the stated limit (see Appendix 1).

* Don't stack the trays one above the other or put them in direct contact with

the walls of the sterilization chamber.

* Always use the instrument tray handle.

* Wrap the tools one by one or, if more tools have to be set in the same wrap,

verify that they are of the same metal;

*Seal the wrap with sterilization adhesive ribbon or by a thermal sealer.

* Don't use metallic clips, pins or other, as this jeopardizes the maintenance

of the sterility;

The water level should not

exceeded this port.

Instructions manual

* Turn the sterilization paper in order to set the plastic part downward

(tray side) and the paper part upward.

Always wrap the tools in case of prolonged store.

5.3 Selecting the sterilization program

5.3.1 LCD

It displays the cycle temperature,

pressure, error code, sterilization

state and program.

5.3.2 temperature button

Select temperature of sterilization.

5.3.3 Program button

Select program of sterilization.

5.3.4 START/STOP button

Press this button to start the sterilization cycle, holding this button above

3 seconds to stop the cycle.

5.3.5 Select the program

Press TEMP button to select the temperature. And press PROGRAM

button to select the program.

TEXTILE OR

DRYING

Notice: The button will be locked for 10 seconds after you switch on.

It initializes its system and check the states during that time.

SOLID

WRAPPED

(CLASS B)

(CLASS N)

5.4 Running the sterilization program.

After selecting program, put the

instruments into the chamber by tray

handle.

5.4.1 After the instruments are loaded, you

may close and lock the door by turning

the door handle clockwise until it stops.

The icon will be lightened.

Caution You must turn the door handle to the maximum position,

otherwise the machine will alarm and stop working

during the cycle.

：

Instructions manual

SOLID

WRAPPED

PRION

LIQUID

B&D TEST

HELIX TEST

VACUUM TEST

DRYING

LIQUID

TEXTILE OR

DRYING

Caution: When you press the "START” button but the door have not to be

closed. You will see the blinks on the screen, You can not

start a cycle until you close the door to the max. position and

press the "Start" button again.

5.4.2 Start the sterilization program.

Press START button the machine will begin the cycle automatically.

It will take 30-75 minutes. (See Appendix 2)

total time or

time count down

of holding time

and end time

total time or

time count down

of holding time

and end time

After a cycle is completed, the printer will start work and print the report

of the sterilization cycle data.(if you connect the printer)

After the pressure is 0, you may open the door, and take out the sterilized

instruments.

5.4.3 Sterilization cycle completion

Always use the tray handle to load or unload the tray in order to

avoid scald.

If you need the instrument urgently. You may set the drying time

to 0. It will skip the drying stage.

Or you may holding the START button for 3 seconds after finish

the holding time and the pressure is 0.

The program will go directly to the last step and skip the drying

stage. After one minute later it will show END.

(CLASS B)

(CLASS N)(CLASS N)

Instructions manual

6 Advanced Setting

6.1.1 Holding the START button and open the

main switch. After about 5 seconds it will

enter the setting screen.

6.1.2 Select the state by press PROGRAM button.

The state you selected will glitter.

Press the START button to enter the setting.

If you select the S1 and enter the state.

You may change the unit of temperature and

pressure, adjust time and date.

6.2.1 You will select the unit of temperature first.

Press TEMP button to select or

The unit you select ed will be lighted. Press

the PROGRAM button to the next item.

6.2.2 You may set the pressure unit as the same

method.

6.2.3 Then press PROGRAM button to the next item to adjust the time and

date. After the last word of the date or time is set , then the data is

permitted to be saved. If you want to finish the setting you shall press

START. It will return to the screen of selecting states.

6.1 Enter the setting

6.2 S1 state

℃.

If use this sterilizer on a place above 2 km, you need to reevaluate the

sterilization result. And you may correct the effect by prolong the

holding time.

The Machine No. And cycle No can not be set by the operator.

6.3 S2 state

6.3.1 You may check the count of sterilization

cycle. It can not be changed by operator.

6.3.2 Set the parameter for high altitude.

If you can't enter the holding time and use

this machine at a high altitude place that is

above 2.0 kilometers or atmospheric

pressure is below 80kPa you need set the

parameter. The scope is 0~2.

6.3.3 Language set:

00 English 01 German 02 Spanish

03 Polish 04 French 05 Magyar

06 Romanian 07 Dutch 08 Lithuanian 09 Latvian

cycle No

machine No

Altitude set

Language

set

5.5 Test programs (CLASS B)

5.5.1 Press PROGRAM button, select the "B&D TEST".

5.5.1.1 Put the Bowie-Dick pack into the

chamber. Then close the door and

press "START".

5.5.1.2 After finish the cycle you check the

indicator. And evaluate the result.

5.5.2 Select the “HELIX TEST"

5.5.2.1 Put the indicator paper in the capsule.

5.5.2.2 Put the Helix tube into the chamber.

Then close the door and press

"START".

5.5.2.3 After finish the cycle you check the

indicator. And evaluate the result.

5.5.3Select the "VACUUM TEST"

5.5.3.1 Then close the door and press

"START" button.

5.5.3.2 After finish it will show the result.

5.5.3.3 In compliance with EN 13060, the

test requires the air leakage rate

less than or equal 0.13kPa/min

during the 10 minutes.

If the leakage rate is not greater 0.13,

it will show 0 means success.

Or it will show F means failure.

5.5.3.4 If the temperature deference between

the max. temperature and the min.

temperature is above 3, it will show

the value T on the screen and show F.

That means the result of test is void.

You need run the vacuum test again

after the chamber has cooled down.

Caution: The VACUUM TEST must be

carried out with unit cold. If

the Tp is greater 3 , it will

show failure.

℃

leakage rate

temperature

deference

11 Instructions manual

Instructions manual

6.5 Printer (Optional)

6.5.1 Connect the printer cable.

6.5.2 Connect the printer power.

holding time

drying time

Notice: We don't suggest the operator to adjust the parameter of

sterilization if it is not necessary.

6.4 S3 state

6.4.1 Adjust the holding time of sterilization and drying time.

Press PROGRAM button to select the program.( )

Press TEMP button to select the temperature of program.

Then press START to adjust the drying time and holding time.

6.4.2 First to adjust the holding time.

Press TEMP button to adjust the data.

Press the PROGRAM button to select

the items.

6.4.3 Press START to save .

6.4.4 Drying time is 0-19.

Holding time of 121 is 1-59.

Holding time of 134 is 1-19.

℃

t1t3t5t8t9

t2t4

t6t7

6.7 Record of the cycle

Select to this interface by PROGRAM button.

It will show cycle No. .

Select the different cycle No. by press

TEMP button.

It will output the information to printer and

USB port after you press START button.

It can be stored the last 20 records.

The sample of content of print and files in memory as below:

CLASS B

Instructions manual

Insert the USB stick to the slot

The information will output to USB stick after the cycle finish

The name of the file is according to the number of machine and

the cycle number

For example

The machine number is E00001

The cycle number is 00012

The file name in the USB stick is 0 0 1200 txt

The first two numbers represent machine number

The middle four numbers represent cycle number

The last two numbers represent error code

00 no error 01 error E01

10 . .

:;:

6.6 USB Flash memory (Optional)

=========================

Program: WRAPPED

Temperature: 134

Pressure: 210.0 kPa

Dry Time: 03Min

Ster Time: 4.0Min

-------------------------------------

time temp. pressure

Start 15:24:20 042.0

T1: 15:32:11 040.0 -78.2kPa

T2: 15:36:08 105.3 052.7kPa

T3: 15:39:21 061.3 -80.4kPa

T4: 15:44:32 110.3 051.6kPa

T5: 15:47:12 067.0 -80.4kPa

T6: 16:00:11 135.2 220.3kPa

TS: 134.8 221.6kPa

MAX.Temperature:135.5

MIN.Temperature:134.1

MAX.Pressure:230.4kPa

MIN.Pressure:212.9kPa

T7: 16:04:02 135.0 223.5kPa

T8: 16:06:32 92.8 -60.1kPa

T9: 16:09:22 90.4 -60.1kPa

End 16:14:12 78.2

--------------------------------------

Cycle No: 0005

Ster Value: Success

Date: 2011-01-18

SN:E00001

Operator:

=======================

℃

=========================

Program: WRAPPED

Temperature: 134

Pressure: 210.0 kPa

Dry Time: 03Min

Ster Time: 4.0Min

-------------------------------------

time temp. pressure

Start 17:34:20 042.0

T1: 17:42:11 040.0 -78.2kPa

T2: 17:46:08 105.3 52.7kPa

T3: 17:49:21 061.3 -80.4kPa

T4: 17:54:32 110.3 51.6kPa

T5: 00:00:00 000.0 000.0kPa

T6: 00:00:00 000.0 000.0kPa

TS: 000.0 000.0kPa

MAX.Temperature:000.0

MIN.Temperature:000.0

MAX.Pressure:000.0kPa

MIN.Pressure:000.0kPa

T7: 00:00:00 000.0 000.0kPa

T8: 00:00:00 000.0 000.0kPa

T9: 00:00:00 000.0 000.0kPa

End 17:54:42 100.2 010.1kPa

--------------------------------------

Cycle No: 0007

Ster Value: Failure E01

Date: 2011-01-18

SN:E00001

Operator:

=======================

℃

t1T3t5

t2t4

=========================

Program: WRAPPED

Temperature: 134

Pressure: 210.0 kPa

Dry Time: 03Min

Ster Time: 4.0Min

-------------------------------------

time temp. pressure

Start 15:24:20 042.0

T1: 15:32:11 070.0 053.2kPa

T2: 15:36:08 075.3 009.7kPa

T3: 15:39:21 090.3 050.4kPa

T4: 15:44:32 094.3 009.6kPa

T5: 15:47:12 119.0 102.4kPa

T6: 16:00:11 110.2 009.3kPa

TS: 134.8 221.6kPa

MAX.Temperature:135.1

MIN.Temperature:134.5

MAX.Pressure:230.4kPa

MIN.Pressure:212.9kPa

T7: 16:04:02 135.0 223.5kPa

T8: 16:06:32 134.8 214.1kPa

End 16:14:12 78.2

--------------------------------------

Cycle No: 0005

Ster Value: Success

Date: 2011-01-18

SN:E00001

Operator:

=======================

℃

=========================

Program: WRAPPED

Temperature: 134

Pressure: 210.0 kPa

Dry Time: 03Min

Ster Time: 4.0Min

-------------------------------------

time temp. pressure

Start 17:34:20 82.0

T1: 17:42:11 090.0 052.2kPa

T2: 17:46:08 085.3 009.7kPa

T3: 17:49:21 108.3 053.4kPa

T4: 17:54:32 100.3 009.6kPa

T5: 00:00:00 0 00.0 000.0kPa

T6: 00:00:00 000.0 000.0kPa

TS: 000.0 000.0kPa

MAX.Temperature:000.0

MIN.Temperature:000.0

MAX.Pressure:000.0kPa

MIN.Pressure:000.0kPa

T7: 00:00:00 000.0 000.0kPa

T8: 00:00:00 000.0 000.0kPa

End 17:54:42 100.2 010.1kPa

--------------------------------------

Cycle No: 0007

Ster Value: Failure E01

Date: 2011-01-18

SN:E00001

Operator:

=======================

℃

CLASS N

Instructions manual

========================

Program Vacuum test

Tp 1

P1 -70.0kPa

P2 -69.0kPa

rate of pressure rise 0.10

Start Time 08:22

End Time 09:01

Date 2011-01-18

Cycle No.:0001

Test Value Success

SN E00001

Operator

========================

：

：℃

：

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MRC Laborausrüstung Handbücher

MRC

MRC YDZ-50K Bedienungsanleitung

MRC

MRC CENVCC-3 Bedienungsanleitung

MRC

MRC PCR-IF-8C Bedienungsanleitung

MRC

MRC 1425 Bedienungsanleitung

MRC

MRC COL-3500 Bedienungsanleitung

MRC

MRC SI-500 Mix Smart Bedienungsanleitung

MRC

MRC CCM-10 Bedienungsanleitung

MRC

MRC PGI-550H Bedienungsanleitung

MRC

MRC Mini Roller ROL-01U Bedienungsanleitung

MRC

MRC Nilsen Bedienungsanleitung

MRC

MRC Compact Bedienungsanleitung

MRC

MRC LOM-300 Bedienungsanleitung

MRC

MRC INE-SGW-1 Bedienungsanleitung

MRC

MRC MH-4D Bedienungsanleitung

MRC

MRC MHK-4D Bedienungsanleitung

MRC

MRC UT-FLU1 Series Bedienungsanleitung

MRC

MRC Fuego SCS basic Bedienungsanleitung

MRC

MRC INE-112N-GC Bedienungsanleitung

MRC

MRC REAC-N10LE-3 Bedienungsanleitung

MRC

MRC ROVAP Series Bedienungsanleitung

MRC

MRC SPECTRO-V11D Bedienungsanleitung

MRC

MRC HSCD-10 Bedienungsanleitung

MRC

MRC AM-4214SD Bedienungsanleitung

MRC

MRC PCR-300 Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung