MRC PM-9100 Bedienungsanleitung
PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATION
MRC.VER.02-11.10
INSTRUCTION MANUAL FOR
PM-9100
Dual & Differential Input
TABLE OF CONTENTS
1. FEATURES...............................................................
.
1
2. SPECIFICATIONS...................................................... 1
2-1 General Specifications......................................... 1
2-2 Electrical Specifications.......................................
.
3
3. FRONT PANEL DESCRIPTION....................................
.
4
3-1 Display.............................................................4
3-2 Power Off/On Button........................................
.
4
3-3 Hold Button......................................................4
3-4 Zero Button.................................................. 4
3-5 " MAX./MIN. " Button........................................4
3-6 Unit Button............... 4
3-7 P1 input socket................................................
.
4
3-8 P2 input socket................................................
.
4
3-9 RS-232 Output Terminal...................................
.
4
3-10 Battery Compartment/Cover.............................. 4
3-11 PLu
g
/quick coupler...........................................
.
4
4. MEASURING PROCEDURE.........................................
.
5
5. AUTO POWER OFF DISABLE......................................6
6. RS232 PC SERIAL INTERFACE................................... 7
7. BATTERY REPLACEMENT..........................................
.
8
1. FEATURES
* Dual & differential input, 2000 mbar max. range.
* Application : Industrial, laboratory, heating,
ventilation, medical hospital, used for dry, non-corrosive and
non-ionic air and gas only. Liquid is prohibited.
* Sensor is built inside the housing.
* Single lugs for pipe connection.
* 8 kind display units ( mbar, psi, Kg/cm 2 mm Hg,
inch Hg, meter HF2 , inch HF2 , Atmosphere ) select
by push button on the front panel
* Auto shut off saves battery life.
* Zero button on the front panel, easy to offset the
zero value.
* Microprocessor circuit assures maximum possible
accuracy, provides special functions and features,
* Super large LCD display with contrast adjustment
for best viewing angle.
* Records maximum & minimum readings with recall.
* Data Hold function for stored the desired value on
display.
* Built-in low battery indicator.
* RS232 PC serial interface, can match the personal
computer used as the Data Logger, Recorder.... &
other modern pressure measuring system.
2
.
S
PE
C
IFI
C
ATI
O
N
S
2-1 General Specifications
Circuit Microprocessor LSI circuit.
Display 61 mm x 34 mm supper large LCD
display. 15 mm ( 0.6" ) digit size.
1
Display units mbar, psi, Kg/cm 2 mm Hg, inch Hg,
meter HF2 , inch HF2 , Atmosphere.
Function Dual & differential input, data hold,
zero/relative, memory.
Zero adjust Push button on the front panel.
Sensor * Sensor is built inside the housing.
* Piezoelectric sensor.
* Used for dry, non-corrosive and
non-ionic air and gas only.
Liquid is prohibited.
Data hold By push button.
Data record Record maximum & minimum readings.
Data output RS 232 PC serial interface.
Sampling time Approx. 0.8 second.
Power off Auto shut off, saves battery life or manual off
by push button.
Operating 0 to 50 蚓( 32 to 122 蚌).
temperature
Operating Less than 80% R.H.
humidity
Power supply 006P DC 9V battery ( heavy duty ).
Power current Approx. DC 6.0 mA.
Weight 345 g/0.76 LB .
Dimension 180 x 72 x 32 mm ( 7.1 x 2.8 x 1.3 inch ).
Accessories * Instruction manual......................
.
1 PC.
included * Hard carryin
g
case....................... 1 PC.
* PLu
g
for quick coupler.................
.
2 PCs.
Optional * Data acquisition software
accessories ( Windows version )........SW-U101-WIN
* RS232 cable.................. UPCB-01
2
2-2 Electrical Specifications
Unit Max. range Resolution
mbar 2000 mbar 1 mbar
psi 29 psi 0.02 psi
Kg/cm 2 2.040 Kg/cm 2 0.001 Kg/cm 2
mm Hg 1500 mm Hg 1 mm Hg
inch Hg 59.05 inch Hg 0.05 inch Hg
meter HF2 20.40 meter HF2 0.01 meter HF2
inch HF2 802 inch HF2 0.5 inch HF2
Atmosphere 1.974 Atmosphere 0.001 Atmosphere
Unit Max. range Accuracy
mbar 2000 mbar 2 % F. S.
psi 29 psi
Kg/cm 2 2.040 Kg/cm 2
Note :
mm Hg 1500 mm Hg
* 23 5 蚓.
inch Hg 59.05 inch Hg
* F.S. : full scale
meter HF2 20.40 meter HF2
* Included linearity,
inch HF2 802 inch HF2
hysteresis and
Atmosphere 1.974 Atmosphere
repeatability
Remark
:
Measuring Display unit
unit
mbar m Bar
psi Psi
Kg/cm 2 Kg /cm 2
mm Hg mm /Hg
inch Hg in/Hg
meter HF2 m HF2
inch HF2 inch HF2
Atmosphere ATP
3
3. FRONT PANEL DESCRIPTION
Fig. 1
3-1 Display 3-7 P1 input socket
3-2 Power Off/On Button 3-8 P2 input socket
3-3 Hold Button 3-9 RS-232 Output
3-4 Zero Button Terminal
3-5 " MAX./MIN. " Button 3-10 Battery Compartment
3-6 Unit Button /Cover
3-11 PLug/ quick coupler
4
4
.
MEASURING PROCEDURE
1)Power on the meter by pressing the " Power Off/On
Button " ( 3-2, Fig. 1 ).
2)Select the desired temperature units ( mbar, psi, Kg/cm 2
mm Hg, inch Hg, meter HF2 , inch HF2 , Atmosphere )
by pushing the " Unit Button " ( 3-6, Fig. 1 ).
3)Zero adjusting
Adjust the display reading to zero value by pushing
the " Zero Button " ( 3-4, Fig. 1 )
4)Install the measuring pipe to " Plug/quick coupler "
( 3-11, Fig. 1 ).
5)The meter is build the two input socket ( P1 input socket,
P2 input socket) for accepting the differential pressure
input.
Connecting the pipe along the " Plug " ( 3-11, Fig. 1) to
a.
" P1 input socket " ( 3-7, Fig. 1 ) only
b.
" P2 input socket " ( 3-8, Fig. 1 ) only
c.
Both P1 & P2 input socket
The LCD will show the measuring pressure value.
Note :
*
If the P1 pressure > P2 pressure, the display will
get positive reading.
*
If the P1 pressure < P2 pressure, the display will
get negative reading.
6)Data Hold
* During the measurement, pressing the " Hold Button "
( 3-3, Fig. 1 ) will freeze the measured value & the LCD
will show " HOLD " symbol.
* Press the " Hold Button " again to cancel the data hold
function. 5
7)Data Record ( Maximum, Minimum reading )
* The DATA RECORD function displays the maximum
and minimum readings. To start the DATA RECORD
function, press the " MAX./MIN. Button " ( 3-5, Fig. 1 )
once. " REC " symbol will appear on the LCD display.
* With the " REC " symbol on the display :
(a) Press the " MAX./MIN. Button " ( 3-5, Fig. 1 )
once, the " Max " symbol along with the maximum
value will appear on the display.
(b) Press the " MAX./MIN. Button " again, the " Min "
symbol along with the minimum value will appear
on the display.
(c) To exit the memory record function, press the
" MAX./MIN. Button " continuously for at least 2
seconds. The display will revert to the current reading.
8)For quick measurement, follow the procedures
shown below :
Main procedures :
POWER
ZERO ADJUS
T
ON
DETERMINE UNI
T
Optional measurin
g
procedures :
DATA HOLD MEMORY RECORD RS232 OUTPUT
Max., Min.
Power mana
g
ement
AUTO POWER OFF or MANUAL POWER OFF
(Not activated durin
g
Memory Record Selection) 6
5. AUTO POWER OFF DISABLE
The instrument has built-in " Auto Power Shut-off " in
order to prolong battery life. The meter will switch off
automatically if none of the buttons are pressed within 10
min.
To de-activate this feature, Select the memory record
function during measurement, by pressing the " MAX./MIN.
Button " ( 3-5, Fig. 1 ).
6. RS232 PC SERIAL INTERFACE
The instrument features an RS232 output via 3.5 mm
Terminal ( 3-9, Fig. 1 ).
The connector output is a 16 digit data stream which
can be utilized to the user's specific application.
An RS232 lead with the following connection will
be required to link the instrument with the PC
serial input.
Meter PC
(3.5 mm jack plug) (9W 'D" Connector)
Center Pin..................................
.
Pin 2
Ground/shield................................Pin 5
7
The 16 digit data stream will be displayed in the
following format :
D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
Each digit indicate the following status :
D0 End Word
D1 to D8 Display readin
g
, D1=LSD, D8=MSD
For example : If the display readin
g
is 1234, the
n
D8 to D1 is 0000123
4
D9 Decimal Point ( DP ) for Upper display.
0 = No DP, 1= 1 DP, 2 = 2 DP, 3 = 3 DP
D10 Polarity 0 = Positive 1 = Ne
g
ative
D11 & D12 Annunciator for Upper Display
mbar = 86 psi = 23
mm Hg = 78 inch Hg = 80
inch HF2 = 25 Kg/cm 2= 77
Atmosphere = 26 meter HF2 = 79
D13 1
D14 4
D15 Start Word
7. BATTERY REPLACEMENT
1)When the left corner of LCD display show " LBT ",
it is necessary to replace the battery. However,
in-spec measurement may still be made for several
hours after low battery indicator appears before the
instrument become inaccurate.
2)Slide the Battery Cover ( 3-10, Fig. 1) away from the
instrument and remove the battery.
3)Install a 9 V battery (PP3 type) and replace the cover.
8
Inhaltsverzeichnis
Andere MRC Messgerät Handbücher
MRC
MRC WA-2017SD Bedienungsanleitung
MRC
MRC INE-DZB-712 Bedienungsanleitung
MRC
MRC BCT-4308 Bedienungsanleitung
MRC
MRC EM-9300SD Bedienungsanleitung
MRC
MRC DW-6163 Bedienungsanleitung
MRC
MRC PS-9303SD Bedienungsanleitung
MRC
MRC CD-4307SD Bedienungsanleitung
MRC
MRC 8758 Bedienungsanleitung
MRC
MRC CC-423 Installationshandbuch
MRC
MRC SPECTRO-UV600 Series Bedienungsanleitung
MRC
MRC HE2 Series Bedienungsanleitung
MRC
MRC PC-6011SD Bedienungsanleitung
MRC
MRC CLRM-200 Bedienungsanleitung
MRC
MRC INE-PHSJ-5 Bedienungsanleitung
MRC
MRC DI-900 Bedienungsanleitung
MRC
MRC PM-1064SD Bedienungsanleitung
MRC
MRC DO-5510 Bedienungsanleitung
MRC
MRC PVB-820 Bedienungsanleitung
MRC
MRC PS-9302 Bedienungsanleitung
MRC
MRC O2H-9903SD Bedienungsanleitung
