National Instruments NI-6587 Bedienungsanleitung

NI-6587

GETTING STARTED GUIDE

NI 6587

NI FlexRIO High-Speed Digital I/O Adapter Module

The NI 6587 is a 1 Gbps per channel high-speed, low-voltage differential signaling (LVDS)

adapter module designed to work in conjunction with your NI FlexRIO™ FPGA module. The

NI 6587 features 20 LVDS channels (16 data and 4 PFI).

This document contains installation instructions and signal information for the NI 6587R,

which is composed of an NI FlexRIO FPGA module and the NI 6587.

Note Before configuring your NI 6587, you must install the appropriate software

and hardware. Refer to the getting started guide for your NI FlexRIO FPGA module

for installation instructions.

The following figure shows an example of a properly connected NI FlexRIO device.

Figure 1. NI FlexRIO Device

NI FlexRIO

Adapter Module + = NI FlexRIO Device

NI FlexRIO

FPGA Module

Contents

Electromagnetic Compatibility Guidelines...............................................................................2

How to Use Your NI FlexRIO Documentation Set...................................................................3

Verifying the System Requirements..........................................................................................4

Front Panel and Connector Pinouts...........................................................................................5

Block Diagrams.........................................................................................................................7

NI 6587 Component-Level Intellectual Property (CLIP)......................................................... 9

NI 6587 CLIP..................................................................................................................10

Cables......................................................................................................................................15

Accessories......................................................................................................................16

Clocking.................................................................................................................................. 18

Installing the Application Software and Driver...................................................................... 20

Installing the NI FlexRIO Devices..........................................................................................20

Unpacking....................................................................................................................... 21

Preparing the Environment............................................................................................. 21

Installing the NI FlexRIO FPGA Module.......................................................................21

Confirming that Measurement & Automation Explorer (MAX) Recognizes the

Device....................................................................................................................... 23

Installing the NI FlexRIO Adapter Module.................................................................... 23

Installing PXI EMC Filler Panels........................................................................................... 24

Uninstalling the Hardware...................................................................................................... 25

Environment............................................................................................................................26

Operating Environment...................................................................................................26

Storage Environment.......................................................................................................26

Shock and Vibration................................................................................................................26

Compliance and Certifications................................................................................................27

Safety.............................................................................................................................. 27

Electromagnetic Compatibility....................................................................................... 27

CE Compliance .............................................................................................................. 27

Online Product Certification........................................................................................... 27

Environmental Management........................................................................................... 28

Where to Go Next................................................................................................................... 28

Worldwide Support and Services............................................................................................ 29

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits are designed to provide reasonable protection against harmful interference when the

product is operated in the intended operational electromagnetic environment.

This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with

radio and television reception and prevent unacceptable performance degradation, install and

use this product in strict accordance with the instructions in the product documentation.

Furthermore, any modifications to the product not expressly approved by National Instruments

could void your authority to operate it under your local regulatory rules.

Caution To ensure the specified EMC performance, operate this product only with

shielded cables and accessories.

Caution To ensure the specified EMC performance, you must attach EMI gaskets

(NI part number 746228-01) to both sides of your NI 6587 before using.

Caution To ensure the specified EMC performance, you must install PXI EMC

Filler Panels (NI part number 778700-01) in all open chassis slots.

2| ni.com | NI 6587 Getting Started Guide

How to Use Your NI FlexRIO Documentation Set

Refer to the following flowchart for information about how to use FlexRIO documentation.

Figure 2. How to Use Your NI FlexRIO Documentation Set.

LabVIEW FPGA

Module Help

NI FlexRIO

Help

LabVIEW

Examples

INSTALL Hardware

and Software

CONNECT Signals

and LearnAbout

Your AdapterModule

LEARN About

LabVIEW FPGA

Module

PROGRAM Your

NI FlexRIO System

in LabVIEW FPGA

Module

Specifications document

for your FPGA module

Specifications document

for your adapter module

Are

You New to

LabVIEW FPGA

Module?

Yes No

Getting Started Guide

for your adapter module

Getting Started Guide

for your FPGA module

NI FlexRIO Adapter

Module Development Kit

User Manual

Table 1. NI FlexRIO Documentation Locations and Descriptions

Document Location Description

Getting started guide

for your FPGA module

Available from the Start menu and

at ni.com/manuals.

Contains installation

instructions for your NI

FlexRIO system.

Specifications

document for your

FPGA module

Available from the Start menu and

at ni.com/manuals.

Contains specifications for

your FPGA module.

Getting started guide

for your adapter

module

Available from the Start menu and

at ni.com/manuals.

Contains signal information,

examples, and CLIP details for

your adapter module.

Specifications

document for your

adapter module

Available from the Start menu and

at ni.com/manuals.

Contains specifications for

your adapter module.

NI 6587 Getting Started Guide | © National Instruments | 3

Table 1. NI FlexRIO Documentation Locations and Descriptions (Continued)

Document Location Description

LabVIEW FPGA

Module Help

Embedded in LabVIEW Help and

at ni.com/manuals.

Contains information about the

basic functionality of the

LabVIEW FPGA Module.

NI FlexRIO Help Available from the Start menu and

at ni.com/manuals.

Contains information about the

FPGA module, adapter

module, and CLIP

configuration information.

NI FlexRIO Adapter

Module Development

Kit User Manual

Available from the Start menu at

Start»All Programs»National

Instruments»NI FlexRIO»NI

FlexRIO Adapter Module

Development Kit»

Documentation.

Contains information about

how to create custom adapter

modules for use with

NI FlexRIO FPGA modules.

LabVIEW Examples Available in NI Example Finder.

In LabVIEW, click Help»Find

Examples»Hardware Input and

Output»FlexRIO.

Contains examples of how to

run FPGA VIs and Host VIs on

your device.

IPNet ni.com/ipnet Contains LabVIEW FPGA

functions and intellectual

property to share.

NI FlexRIO product

page

ni.com/flexrio Contains product information

and data sheets for NI FlexRIO

devices.

Verifying the System Requirements

To use the NI FlexRIO Adapter Module Support instrument driver, your system must meet

certain requirements. For more information about minimum system requirements,

recommended system, and supported application development environments (ADEs), refer to

the NI FlexRIO Adapter Module Support Readme, which is available on the NI FlexRIO

Adapter Module Support software DVD or online at ni.com/updates.

4| ni.com | NI 6587 Getting Started Guide

Front Panel and Connector Pinouts

The NI 6587 provides one PFI signal and one clock signal through the two SMA connectors

on the device front panel. The NI 6587 also provides the following signals on the Digital Data

& Control (DDC) connector:

• Sixteen LVDS signals

• Four LVDS PFI signals

• Three single-ended PFI signals

• One LVDS clock out signal

The following figure shows the front panel connector and signal descriptions for the NI 6587.

Figure 3. NI 6587 Front Panel and Connector Pinout

NI 6587

PFI 0

CLOCK IN

1 Gbps

LVDS

GND

PFI 1+

GND

PFI 2+

GND

PFI 3+

GND

DIO 0+

GND

DIO 1+

GND

DIO 2+

GND

DIO 3+

GND

DIO 4+

GND

DIO 5+

GND

DIO 6+

GND

DIO 7+

GND

DIO 8+

GND

DIO 9+

GND

DIO 10+

GND

DIO 11+

GND

DIO 12+

GND

DIO 13+

GND

DIO 14+

GND

DIO 15+

GND

PFI 1–

PFI 2–

PFI 3–

DIO 0–

DIO 1–

DIO 2–

DIO 3–

DIO 4–

DIO 5–

DIO 6–

DIO 7–

DIO 8–

DIO 9–

DIO 10–

DIO 11–

DIO 12–

DIO 13–

DIO 14–

DIO 15–

3332

4544

4847

5756

6968

SE_PFI_3

SE_PFI_2

DDC CLK OUT–

DDC CLK OUT+

GND

SE_PFI_1

STROBE–

STROBE+

PFI 4 –

PFI 4+

NI 6587 Getting Started Guide | © National Instruments | 5

Caution To avoid permanent damage to the NI 6587, disconnect all signals

connected to the NI 6587 before powering down the module, and connect signals

only after the adapter module has been powered on by the NI FlexRIO FPGA

module.

Caution Connections that exceed any of the maximum ratings of any connector on

the NI 6587 can damage the device and the chassis. NI is not liable for any damage

resulting from such connections.

Note If you design a custom cabling solution with the InfiniBand connector

(779157-01) and the SHB12X-B12X LVDS shielded cable (192344-01), the NI 6587

pinout is reversed at the end connector. For example, the signal shown on pin 1 maps

to pin 73 in the pinout at the end connector.

The following table contains pin location information and signal information for the SMA

connectors on the NI 6587.

Table 2. SMA Connector Names and Descriptions

Signal Name Connector Signal Type Signal Description

PFI 0 PFI 0 Control Bidirectional single-ended terminal for channel

PFI 0.

CLOCK IN CLOCK IN Clock External single-ended clock input terminal.

The following table contains pin location information and signal information for the DDC

connectors on the NI 6587.

Table 3. NI 6587 DDC Connector Names and Descriptions

Signal Name Pin(s) Signal Type Signal Description

DDC CLK OUT+ 65 Control Positive terminal for the LVDS

exported Sample Clock.

DDC CLK OUT- 66 Control Negative terminal for the LVDS

exported Sample Clock.

STROBE+ 62 Control Positive differential terminal for the

external Sample Clock source that

can be used for synchronous

dynamic acquisition.

STROBE- 63 Control Negative differential terminal for

the external Sample Clock source

that can be used for synchronous

dynamic acquisition.

6| ni.com | NI 6587 Getting Started Guide

Table 3. NI 6587 DDC Connector Names and Descriptions (Continued)

Signal Name Pin(s) Signal Type Signal Description

DIO<0..15>+ 14, 17, 20, 23, 26,

29, 32, 35, 38, 41,

44, 47, 50, 53, 56, 59

Data Positive differential terminal for the

bidirectional digitial I/O data

channels 0 through 15.

DIO<0..15>- 15, 18, 21, 24, 27,

30, 33, 36, 39, 42,

45, 48, 51, 54, 57, 60

Data Negative differential terminal for

the bidirectional digital I/O data

channels 0 through 15.

PFI <1..4>+ 2, 5, 8, 11 Control Positive differential terminals for

bidirectional PFI channels 1

through 4.

PFI <1..4>- 3, 6, 9, 12 Control Negative differential terminals for

bidirectional PFI channels 1

through 4.

SE_PFI<1..3> 68, 71, 72 Control Single-ended terminals for

bidirectional PFI channels 1

through 3.

GND 1, 4, 7, 10, 13, 16,

19, 22, 25, 28, 31,

34, 37, 40, 42, 46,

49, 52, 55, 58, 69

Ground Ground reference for signals.

For more detailed information about the NI 6587 front panel connectors, refer to the NI 6587

Specifications.

Block Diagrams

Figures 4 through 8 show the data flow through the NI 6587. Single-ended data lines use

standard clock levels to interpret data as either a binary zero or a one in high-speed digital data

transfers. Differential data lines provide a low-noise, low-power, low-amplitude differential

method for high-speed digital data transfer.

Figure 4. Clock Input Signal

CLOCK IN

Global Clock to

NI FlexRIO FPGA Module

(UserGclkLvttl)

NI 6587 Getting Started Guide | © National Instruments | 7

Figure 5. LVDS Data and PFI Lines

Data from

NI FlexRIO FPGA Module

(GPIO Output)

110 Ohm

Data to

NI FlexRIO FPGA Module

(GPIO Input)

110 Ohm

Switch

DIO <0..15>

DIO <0..15>+ and

PFI <1..4>+

Direction Control from

NI FlexRIO FPGA Module

(GPIO Direction)

and

PFI <1..4>

Figure 6. Single-Ended PFI Lines

Data from

NI FlexRIO FPGA Module

(GPIO Output)

Output Enable from

NI FlexRIO FPGA Module

(GPIO Direction)

Data to

NI FlexRIO FPGA Module

(GPIO Input)

SE_PFI <1..3>

and PFI 0

50 Ohm

Figure 7. Clock Output Signals

Clock from

NI FlexRIO FPGA Module

(GPIO Output)

Output Enable from

NI FlexRIO FPGA Module

(GPIO Direction)

DDC CLK OUT+

LVDS

LVDS DDC CLK OUT

Switch

110 Ohm

10 kOhm 10 kOhm

8| ni.com | NI 6587 Getting Started Guide

Figure 8. Crosspoint Switch

Sync Clock (PXIe Only)

Adapter Module Onboard Clock

STROBE

Reserved

Strobe Bypass Control

from NI FlexRIO FPGA Module

(GPIO_8_n)

2 2

Generation Bank I/O Clock

to NI FlexRIO FPGA Module

GPIO_26_CC

GPIO_26_n_CC

PFI Bank I/O Clock

to NI FlexRIO FPGA Module

GPIO_38_CC

GPIO_38_n_CC

Global Clock

to NI FlexRIO FPGA Module

UserGclkLvds

UserGclkLvds_n

Acquisition Bank I/O Clock

to NI FlexRIO FPGA Module

GPIO_56_CC

GPIO_56_n_CC

4×4

Crosspoint

Switch

Related Information

NI 6587 Component-Level Intellectual Property (CLIP) on page 9

NI 6587 Component-Level Intellectual Property

(CLIP)

The LabVIEW FPGA Module includes component-level intellectual property (CLIP) for HDL

IP integration. NI FlexRIO devices support two types of CLIP: user-defined and socketed.

•User-defined CLIP allows you to insert HDL IP into an FPGA target, enabling VHDL

code to communicate directly with an FPGA VI.

•Socketed CLIP provides the same IP integration of the user-defined CLIP, but also allows

the CLIP to communicate directly with circuitry external to the FPGA. Adapter module

socketed CLIP allows your IP to communicate directly with both the FPGA VI and the

external adapter module connector interface.

The following figure shows the relationship between an FPGA VI and the CLIP.

Inhaltsverzeichnis

Andere National Instruments E/A-System Handbücher

National Instruments

National Instruments PCIe-6323 Bedienungsanleitung

National Instruments

National Instruments NI 9423 Bedienungsanleitung

National Instruments

National Instruments NI 9236 Bedienungsanleitung

National Instruments

National Instruments NI 6581 Bedienungsanleitung

National Instruments

National Instruments FD-11634 Bedienungsanleitung

National Instruments

National Instruments SCXI SCXI-1102 Handbuch

National Instruments

National Instruments NI 9752 Bedienungsanleitung

National Instruments

National Instruments PXI-6238 Bedienungsanleitung

National Instruments

National Instruments cRIO-9075 Bedienungsanleitung

National Instruments

National Instruments CB-2162 Bedienungsanleitung

National Instruments

National Instruments R Series Bedienungsanleitung

National Instruments

National Instruments R Series Bedienungsanleitung

National Instruments

National Instruments NI PCIe-7821R Bedienungsanleitung

National Instruments

National Instruments Quadrature Input Module FP-QUAD-510 Bedienungsanleitung

National Instruments

National Instruments 9218 Handbuch

National Instruments

National Instruments FD-11637 Bedienungsanleitung

National Instruments

National Instruments NI 9411 Bedienungsanleitung

National Instruments

National Instruments NI 9265 Gebrauchs- und Pflegehandbuch

National Instruments

National Instruments FieldPoint FP-1300 Bedienungsanleitung

National Instruments

National Instruments SCXI-1126 Bedienungsanleitung

National Instruments

National Instruments R Series Intelligent DAQ PCI/PXI-783xR Bedienungsanleitung

National Instruments

National Instruments 9216 Handbuch

National Instruments

National Instruments NI PXI-1042 Series Bedienungsanleitung

National Instruments

National Instruments NI REM-11100 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung