National Instruments 9775 Bedienungsanleitung
GETTING STARTED GUIDE
NI 9775
4-Ch, ±10 V, 20 MS/s, 14-Bit Digitizer
This document explains how to connect to the NI 9775.
Note Before you begin, complete the software and
hardware installation procedures in your chassis
documentation.
Note The guidelines in this document are specific to
the NI 9775. The other components in the system might
not meet the same safety ratings. Refer to the
documentation for each component in the system to
determine the safety and EMC ratings for the entire
system.
Safety Guidelines
Operate the NI 9775 only as described in this document.
Caution Do not operate the NI 9775 in a manner not
specified in this document. Product misuse can result in
a hazard. You can compromise the safety protection
built into the product if the product is damaged in any
way. If the product is damaged, return it to NI for
repair.
2| ni.com | NI 9775 Getting Started Guide
Safety Voltages
Connect only voltages that are within Measurement Category O.
Isolation
Channel-to-channel None
Channel-to-earth
ground
None
Note Measurement Categories CAT I and CAT O are
equivalent. These test and measurement circuits are not
intended for direct connection to the MAINS building
installations of Measurement Categories CAT II,
CAT III, or CAT IV.
Caution Do not connect the NI 9775 to signals or use
for measurements within Measurement Categories II,
III, or IV.
Safety Guidelines for Hazardous Locations
The NI 9775 is suitable for use in Class I, Division 2, Groups A,
B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4
and Ex nA IIC T4 hazardous locations; and nonhazardous
NI 9775 Getting Started Guide | © National Instruments | 3
locations only. Follow these guidelines if you are installing the
NI 9775 in a potentially explosive environment. Not following
these guidelines may result in serious injury or death.
Caution Do not disconnect I/O-side wires or
connectors unless power has been switched off or the
area is known to be nonhazardous.
Caution Do not remove modules unless power has
been switched off or the area is known to be
nonhazardous.
Caution Substitution of components may impair
suitability for Class I, Division 2.
Caution For Division 2 and Zone 2 applications,
install the system in an enclosure rated to at least IP54
as defined by IEC/EN 60079-15.
Special Conditions for Hazardous Locations Use in
Europe and Internationally
The NI 9775 has been evaluated as Ex nA IIC T4 Gc equipment
under DEMKO 12 ATEX 1202658X and is IECEx UL 14.0089X
certified. Each NI 9775 is marked II 3G and is suitable for use
in Zone 2 hazardous locations, in ambient temperatures of -40 °C
4| ni.com | NI 9775 Getting Started Guide
≤ Ta ≤ 70 °C. If you are using the NI 9775 in Gas Group IIC
hazardous locations, you must use the device in an NI chassis that
has been evaluated as Ex nC IIC T4, Ex IIC T4, Ex nA IIC T4, or
Ex nL IIC T4 equipment.
Caution You must make sure that transient
disturbances do not exceed 140% of the rated voltage.
Caution The system shall only be used in an area of
not more than Pollution Degree 2, as defined in
IEC/EN 60664-1.
Caution The system shall be mounted in an
ATEX/IECEx-certified enclosure with a minimum
ingress protection rating of at least IP54 as defined in
IEC/EN 60079-15.
Caution The enclosure must have a door or cover
accessible only by the use of a tool.
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory
requirements and limits for electromagnetic compatibility (EMC)
stated in the product specifications. These requirements and
limits provide reasonable protection against harmful interference
NI 9775 Getting Started Guide | © National Instruments | 5
when the product is operated in the intended operational
electromagnetic environment.
This product is intended for use in industrial locations. However,
harmful interference may occur in some installations, when the
product is connected to a peripheral device or test object, or if the
product is used in residential or commercial areas. To minimize
interference with radio and television reception and prevent
unacceptable performance degradation, install and use this
product in strict accordance with the instructions in the product
documentation.
Furthermore, any changes or modifications to the product not
expressly approved by National Instruments could void your
authority to operate it under your local regulatory rules.
Caution To ensure the specified EMC performance,
operate this product only with shielded cables and
accessories. Do not use unshielded cables or
accessories unless they are installed in a shielded
enclosure with properly designed and shielded input/
output ports and connected to the product using a
shielded cable. If unshielded cables or accessories are
6| ni.com | NI 9775 Getting Started Guide
not properly installed and shielded, the EMC
specifications for the product are no longer guaranteed.
Caution To ensure the specified EMC performance,
the length of all I/O cables must be no longer than 30 m
(100 ft).
Special Conditions for Marine Applications
Some products are Lloyd’s Register (LR) Type Approved for
marine (shipboard) applications. To verify Lloyd’s Register
certification for a product, visit ni.com/certification and search
for the LR certificate, or look for the Lloyd’s Register mark on
the product.
Caution In order to meet the EMC requirements for
marine applications, install the product in a shielded
enclosure with shielded and/or filtered power and
input/output ports. In addition, take precautions when
designing, selecting, and installing measurement probes
and cables to ensure that the desired EMC performance
is attained.
NI 9775 Getting Started Guide | © National Instruments | 7
Preparing the Environment
Ensure that the environment in which you are using the NI 9775
meets the following specifications.
Operating temperature
(IEC 60068-2-1, IEC 60068-2-2)
-40 °C to 70 °C
Operating humidity
(IEC 60068-2-78)
10% RH to 90% RH,
noncondensing
Pollution Degree 2
Maximum altitude 5,000 m
Indoor use only.
Note Refer to the device datasheet on ni.com/manuals
for complete specifications.
8| ni.com | NI 9775 Getting Started Guide
NI 9775 Pinout
AI0
CHASSIS
GND
AI1
CHASSIS
GND
AI2
CHASSIS
GND
AI3
CHASSIS
GND
NI 9775 Getting Started Guide | © National Instruments | 9
Andere Handbücher für 9775
1
Inhaltsverzeichnis
Andere National Instruments Messgerät Handbücher
National Instruments
National Instruments NI SCXI-1336 Bedienungsanleitung
National Instruments
National Instruments PXI-4130 Handbuch
National Instruments
National Instruments 9235 Bedienungsanleitung
National Instruments
National Instruments NI 9263 Bedienungsanleitung
National Instruments
National Instruments PXI-4070 6 1/2 Digit FlexDMM Handbuch
National Instruments
National Instruments VirtualBench VB-8034 Bedienungsanleitung
National Instruments
National Instruments PCIe-5763 Bedienungsanleitung
National Instruments
National Instruments PXIe-5665 Bedienungsanleitung
National Instruments
National Instruments USB-5683 Bedienungsanleitung
National Instruments
National Instruments PXIe-6570 Bedienungsanleitung
National Instruments
National Instruments NI 435 Series Bedienungsanleitung
National Instruments
National Instruments NI 9213 Bedienungsanleitung
National Instruments
National Instruments PXIe-5665 Gebrauchs- und Pflegehandbuch
National Instruments
National Instruments NI PXIe-4143 Betriebsanleitung
National Instruments
National Instruments PXI-5663 Handbuch
National Instruments
National Instruments 9211A Bedienungsanleitung
National Instruments
National Instruments NI 5731 Series Bedienungsanleitung
National Instruments
National Instruments PCIe-5774 Bedienungsanleitung
National Instruments
National Instruments NI PXIe-5105 Bedienungsanleitung
National Instruments
National Instruments 446 Series Handbuch
