NETGEAR WG302v2 - ProSafe 802.11g Wireless Access... Betriebsanleitung

5-1

v1.0, October 2007

Chapter 5

Troubleshooting

This chapter provides information about troubleshooting your ProSafe 802.11g Wireless Access

Point. After each problem description, instructions are given to help you diagnose and solve the

problem. For the common problems listed, go to the section indicated.

• Is the WG302v2 on?

Go to “Front Panel” on page 1-5.

• Have I connected the wireless access point correctly?

Go to “Installing the ProSafe 802.11g Wireless Access Point” on page 2-3.

• I cannot remember the wireless access point’s configuration password.

Go to “Viewing the Activity Log” on page 3-9.

If you have trouble setting up your WG302v2, check the tips below.

No lights are lit on the access point.

It takes a few seconds for the power indicator to light up. Wait a minute and check the power light

status on the access point.

If the access point has no power.

• Make sure the power cord is connected to the access point.

• Make sure the power adapter is connected to a functioning power outlet. If it is in a power

strip, make sure the power strip is turned on. If it is plugged directly into the wall, verify that it

is not a switched outlet.

• Make sure you are using the correct NETGEAR power adapter supplied with your access

point.

NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual

5-2 Troubleshooting

v1.0, October 2007

The Wireless LAN activity light does not light up.

The access point’s antennae are not working.

• If the Wireless LAN activity light stays off, disconnect the adapter from its power source and

then plug it in again.

• Make sure the antennas are tightly connected to the WG302v2.

• Contact NETGEAR technical support if the Wireless LAN activity light remains off.

The LAN light is not lit.

There is a hardware connection problem. Check these items:

• Make sure the cable connectors are securely plugged in at the access point and the network

device (hub, switch, or router). A switch, hub, or router must be installed between the access

point and the Ethernet LAN or broadband modem.

• Make sure the connected device is turned on.

• Be sure the correct cable is used. Use a standard Category 5 Ethernet patch cable. If the

network device has Auto Uplink™ (MDI/MDIX) ports, you can use either a crossover cable or

a normal patch cable.

I cannot access the Internet or the LAN with a wireless

capable computer.

There is a configuration problem. Check these items:

• You might not have restarted the computer with the wireless adapter to have TCP/IP changes

take effect. Restart the computer.

• The computer with the wireless adapter may not have the correct TCP/IP settings to

communicate with the network. Restart the computer and check that TCP/IP is set up properly

for that network. The usual setting for Windows the Network Properties is set to “Obtain an IP

address automatically.”

• The access point’s default values may not work with your network. Check the access point

default configuration against the configuration of other devices in your network.

NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual

Troubleshooting 5-3

v1.0, October 2007

I cannot connect to the WG302v2 to configure it.

Check these items:

• The WG302v2 is properly installed, LAN connections are OK, and it is powered on. Check

that the LAN port LED is on (amber indicating a 10 Mbps Ethernet connection or green

indicating a 100 Mbps Ethernet connection) to verify that the Ethernet connection is OK.

• The default configuration of the WG302v2 is for a static IP address of 192.168.0.228 and a

Mask of 255.255.255.0 with DHCP disabled. Make sure your network configuration settings

are correct.

• If you are using the NetBIOS name of the WG302v2 to connect, ensure that your computer

and the WG302v2 are on the same network segment or that there is a WINS server on your

network.

• If your computer is set to “Obtain an IP Address automatically” (DHCP client), restart it.

• If your computer uses a Fixed (Static) IP address, ensure that it is using an IP Address in the

range of the WG302v2. The WG302v2 default IP Address is 192.168.0.228 and the default

Subnet Mask is 255.255.255.0.

When I enter a URL or IP address I get a timeout error.

A number of things could be causing this. Try the following troubleshooting steps.

• Check whether other PCs work. If they do, ensure that your PCs TCP/IP settings are correct. If

using a Fixed (Static) IP Address, check the Subnet Mask, Default Gateway, DNS, and IP

Addresses.

• If the PCs are configured correctly, but still not working, ensure that the WG302v2 is

connected and turned on. Connect to it and check its settings. If you cannot connect to it, check

the LAN and power connections.

• If the WG302v2 is configured correctly, check your Internet connection (DSL/Cable modem

etc.) to make sure that it is working correctly.

•Tryagain.

NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual

5-4 Troubleshooting

v1.0, October 2007

I am unable to download files from some FTP sites.

If the IP address of the WG302v2 LAN interface is not on the same network as the IP addresses

the DHCP server on the WG302v2 assigns to wireless clients, the WG302v2 performs automatic

network address and port translation (NAPT). Some higher-layer protocols, such as FTP, might not

work with the NAPT on the WG302v2.

To fix this issue, reconfigure the DHCP server settings (Advanced IP Settings) so that the wireless

clients receive IP addresses that are on the same network as the WG302v2 Ethernet interface.

I need to restore factory default settings.

To restore the factory default settings, you can use the Reset button (see “Using the Reset Button

to Restore Factory Default Settings” on page 3-6) or use the Backup/Restore Settings menu (see

“Erasing the Configuration” on page 3-6). To view a list of the factory default settings, see

“Default Factory Settings” on page B-1.

Andere Handbücher für WG302v2 - ProSafe 802.11g Wireless Access...

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NETGEAR Drahtloser Zugangspunkt Handbücher

NETGEAR

NETGEAR WAC104 Bedienungsanleitung

NETGEAR

NETGEAR WND930 Bedienungsanleitung

NETGEAR

NETGEAR WG602 - 54 Mbps Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR WG602v1 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR prosafe WAC740 Bedienungsanleitung

NETGEAR

NETGEAR WN802T Bedienungsanleitung

NETGEAR

NETGEAR ProSafe Premium WNDAP660 Bedienungsanleitung

NETGEAR

NETGEAR WN802Tv2 - Wireless-N Access Point Bedienungsanleitung

NETGEAR

NETGEAR WAC720 Bedienungsanleitung

NETGEAR

NETGEAR WAC120 Bedienungsanleitung

NETGEAR

NETGEAR ME103 - 802.11b ProSafe Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR WG602v4 - Wireless Access Point Handbuch

NETGEAR

NETGEAR WAG102 - ProSafe Dual Band Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR WNDAP350 - ProSafe 802.11n Dual Band Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR WG302 - 802.11g ProSafe Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR WAC505 Bedienungsanleitung

NETGEAR

NETGEAR WAG302v1 - ProSafe Dual Band Wireless Access... Bedienungsanleitung

NETGEAR

NETGEAR ProSafe WG102-500 Bedienungsanleitung

NETGEAR

NETGEAR WE102 - Wireless Access Point Bedienungsanleitung

NETGEAR

NETGEAR XWN5001 Bedienungsanleitung

NETGEAR

NETGEAR WAX610 Bedienungsanleitung

NETGEAR

NETGEAR ProSafe WNAP320 Bedienungsanleitung

NETGEAR

NETGEAR WAX615-100NAS Bedienungsanleitung

NETGEAR

NETGEAR WAC124-100NAS Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung