Netvox Z809B Bedienungsanleitung

ZigBeeTM-Power Socket with Power Consumption Monitoring

User Manual

Dimmable Socket with Power Detection

Model: Z809B

Energy Consumption Monitoring Series

For Home Automation

20150105

FW V5.0

HW V1.3

Z809B

Other Netvox related devices

Switch controller



Simple controller Z501 series

Multiple/Scene controller Z503



Wall switch ZB02 series



Light sensing switch Z302B

On/Off Status Indicator

(red | green)

Button switch

Network Indicator

(red | green)

Binding key

Introduction

NETVOX Z809B is a ZigBee Home Automation enabled power socket with level control

and power/energy/current/voltage consumption monitoring. It acts as a router device in

the Home Automation profile network. It can be manually switched through a soft on/off

switch or switched wirelessly through a paired remote controller. Consumption reading

can be captured and displayed on ZiG-BUTLER -Netvox application software, or on any

3rd party ZigBee enabled in-home display.

What is ZigBee?

ZigBee is a short range wireless transmission technology which defined for a minimum

complexity, low power consumption, low data rate, cost effective wireless solution. ZigBee

lies in between wireless markup technology and Bluetooth. ZigBee is based on

IEEE802.15.4 standard, the mutual co-ordination between thousands of sensors to

exchange data. Sensor to sensor or node-to-node communication is achieved through

relays of control data between devices with only a fraction of energy use which denoted

for highly transmission efficiency.

Note: Wireless communication, in some real use cases, can be limited by the signal

blockage. Please consult your service provider or place of purchase.

Product Specification

Fully IEEE 802.15.4 compliant (ZigBee

Pro)

Utilizes 2.4GHz ISM band, up to 16

channels

Up to 150 meters non-obstacle

wireless transmission distance

100~240VAC, 50/60HZ input power

Resistive load max: 3A/220VAC

Consumption monitoring range 50mA

to 3A, with ±1% accuracy

Up to 150 meters non-obstacle

wireless transmission distance

Simple operation and device

configuration

Operating Ambient: -10 oC to 50oC / 5~85% RH

max.

Storage Ambient: -40 oC to 85oC

Setting up the Z809B and network

To allow Z809B to function, it must first join to a ZigBee network. When it is given powered

it will automatically start searching for an existed network. So before you give power to

Z809B, please make sure it is within the wireless coverage distance (150 meters or less)

and make sure first you have the permit-join feature enabled either on a coordinator or

a router device in the network so that when Z809B is powered on Z809B will automatically

join to the network.

*For how to enable permit-join please refer to the router or coordinator device user manual

Operation:

Make sure you have detached any home appliance from Z809B. And also restore the

device back to its factory default setting. Refer to Restore to factory setting section.

Step 1: Make sure you have open up permit-join function (valid for 60 seconds) of a

coordinator or a router

Step 2: Now plug in Z809B into AC power socket to power it. Z809B device will start to

search for the network within reach.

Step 3: if joining is successful, the green network light will turn solid lit.

Setting Up Summary

(1) Startup and network association

(2) Bind the device with other device where applicable (i.e. bind it with a ZigBee

switch for wireless control).

(3) It is ready to be used.

Step 1. Startup and Network Association

Note: please also refer to Absent of Coordinator Indication

section of the manual.

To wirelessly control Z809B, it is required to pair with ZigBee enabled on/off/level

controller. If you do not wish to control Z817B with a remote or a switch, you may skip this

step and go to How to use Z809B.

Pairing operation:

1). Hold press the binding key for 3 seconds until you see the network indicator

flash green once while it sends binding request to the air.

2). Likewise, do the same on the level switch to exchange binding according to the

instructions of that device

3). When binding is successful the green indicator on Z809B will flash 5 times then

return to solid lit. If successful you should be able to wireless control Z809B.

Otherwise it flashes quickly 10 times indicating pairing unsuccessful.

Clear pairing setting:You may remove the pairing between the two or more devices.

Unbinding procedure is exactly the same as binding operation. When you repeat the

binding operation, the two devices will remove the binding information stored..

Step 2. Device pairing for On/Off/Level control (binding)

How to use Z809B

Dimmer

Z809B is only suitable for dimming use. Application such as light level control is applicable

where dimmable light bulbs are used. Non-dimmable light bulbs are not to be used with

this device as the dimming effect will not be obvious.

Remote control

When the device has joined to the network and paired (see Device pairing for

On/Off/Level control) with a remote controller the device is ready to be used. Z809B

should now be able to responds to on, off, level control command from a wireless remote

controller.

Operation: If the Z809B device is properly paired with a switch device, you should see

Z809B respond to on or off instruction wirelessly.

When the Off button is press twice and then press On button once, Z809B will stay Off.

This is to prevent from accidental turning the device on.

Manual switch

When the button switch is pressed, Z809B increases the output by 1/8th. As you keep

pressing until it passes the brightest, Z809B will decrement the output until its output is

totally turned off.

The On/Off status indicator turns red when the output is totally Off or green when output is

On.

Absent of Coordinator Indication

A ZigBee network required a coordinator to maintain network and other services. Z809B

would indicate to the user of whether the coordinator is present or is within the effective

signal transmission by means of LED indication.

After Z809B joined to a network, it checks once every 10 minutes for the coordinator. After

3 detecting attempts that the coordinator is not within the effective range, its network

indicator will flash 30 times in green. In the normal operation, the network indicator stays

solid green without flashing.

Permit other device to join

Z809B is featured to be a router in the network. It permits other devices to join the network.

In normal operation, by default the router device Z809B does not permit any device to join

to the network to protect the network from unexpected or unauthorized join attempt. You

will need to open up the permit-join on Z809B or on other router device to allow new

devices (a router or an end device) to join.

Operation:

1. Short press the binding key once.

2. The permit join is now enabled for 60 seconds and the green network indicator will

flash 60 times.

3. Z809B waits the new device to join in automatically. Please note that the maximum

waiting time to join is 60 seconds. Repeat the process if you missed the 60 seconds

period.

Power Consumption Reporting

When the load is attached to the device, the embedded meter reads the supplied current

drawn overtime. Z809B reports the readings to a paired target device normally an in-home

display or consumption data logger. Ensure that you go through Consumption reporting

and also Configure reporting time interval described in ZiG-BUTLER page, otherwise

Z809B will not sent consumption reading properly when misconfigured.Z809B can report

the consumption reading to Netvox’s ZiG-BUTLER or to any 3rd party in-home display.

If target device pairing is not done (refer to Consumption reporting in ZiG-BUTLER

section),Z809B will, by default, report at time interval of 180s minimum or 300s maximum.

The reportable change is 2048.

Units

Power drawn overtime is measured. Current (unit mA), Voltage (unit V), Power (unit kW)

and Energy (unit kWh). Z809B stores a new value read and updates such value and

clears up the previous. User may want to return the reading back to zero when wish. Refer

to Resetting Power Consumption Summation section bellow.

Possible reading losses

Z809B stores the reading to the memory at every 30 seconds and 15 seconds for some

Z809B. If power is disconnected from power source, the reading in the temporal buffer will

not be recorded.

Reading accuracy

If the output current is above 50mA, the reading accuracy of current, voltage, power and

energy is ±1%. Current detection range is between 50mA to 3A.

Resetting Power Consumption Summation

Z809B updates and stores the last energy reading in kwh. In some cases user would wish

to return the counter to zero. Same feature can be found in ZiG-BUTLER software with the

Recalculate button.

Operation:

Hold press Binding Key for 20 seconds then release the key when the green network

indicator flashes 4 times, within 2 seconds, short press the button switch once. If

successful the green network indicator will flash once.

Restore to factory setting

Z809B is capable of storing and saving includes network routing information. If you wish to

remove Z809B from an exited network, you would need to clear the saved routing

information to join to a new network by simply reset the device to restore to the factory

setting.

*notes: restore Z809B back to factory default will not reset power consumption summation.

Please refer to Resetting Power Consumption Summation section above.

Operation

1. While the device is given power, hold press the binding key for 15 seconds then

release the key when the green network indicator flashes 3 times then, within 2 seconds,

short press the button switch once.

2. If restore to factory setting is successful, you should see the indicator light flashes 10

times.

Soon the device will reboot by itself. In so the entire ZigBee network and required

information is cleared. It will enter network search to attempt to join to a network. Refer to

network association section of this manual.

Power Overload

Upon detecting current exceeds 5A, the output will be switched off within 30 seconds.

Summary of Key function and corresponding display

Function Key Display

Restore to factory

setting

Hold press binding key

15s then within 2s

press test button once.

3 flashes (hold press

binding key)

Then 10 flashes if

successful

Permit Join Short press binding

key once

Flashes 60 times in

60 seconds.

Resetting power

consumption

summation

Hold press binding key

20s then within 2s

short press test button

once.

4 flashes (hold press

binding key)

1 flash (test button

once)

Device Pairing Hold press binding key

3s.

1 flash (hold press

binding key)

5 flashes if

successful,

otherwise flashes

quickly 10 times

Configuration setting

As mentioned in How to use Z809B section, when the Off button is press twice and then

press On button once, Z809B will stay Off. This is to prevent from accidentally turning the

device on. This is a factory default setting. Programmer may, however, overwrite this

setting permanently by setting On Level attribute to any value between 0x00 to 0xFE.

0xFF is the factory default.

Installation Notes:

1、Z809B stores power consumption data once every 30 seconds, thus the power

data of last 30 seconds before power-fail could probably be lost. （24C01, 30

seconds; 24C02, 15 seconds….）

2、 Z809B is designed as a light dimmer. No other electric appliances but dimmable

lights can be attached to this product.

3、 Z809B is not a waterproof product, use it indoor only.

4、Load Protection: The current is over 3A → it will be off-load in 2 seconds.

5、After it is off-load, the Bit1 (Current OverLoad) of the parameter ACAlarmsMask

will be checked:

Bit1 (Current OverLoad) is 1 →it sends the alarm message;

Bit1 (Current OverLoad) is 0 →it doesn’t send the alarm message

When it sends the alarm message →AlarmCluster = 0x0B04; AlarmCode = 0xF0;

indicator flashes 10 times.

6、Z809B is using PWM dimming with leading Triac technology. Please DO NOT use

improper light/lamp/device or it may cause damages. For example, regular LED

lamp which does not support dimmer features, gas-discharge lamp, home

appliance, computer, or on-off relay is not supported.

7、The maximum electrical load of Z809B:

a. Resistive Load (incandescent light bulb): 3A/600W.

b. Dimmable fluorescent lamp or dimmable LED lamp: 100W. Parallel

connection is not recommended.

c. DO NOT connect coil transformer for dimming.

Inhaltsverzeichnis

Andere netvox Zubehör Handbücher

netvox

netvox Z808B Bedienungsanleitung

netvox

netvox R718PB13 Bedienungsanleitung

netvox

netvox RB11E Bedienungsanleitung

netvox

netvox R718PB15 Bedienungsanleitung

netvox

netvox R718UBD Series Bedienungsanleitung

netvox

netvox R711 Bedienungsanleitung

netvox

netvox R718NL3 Series Bedienungsanleitung

netvox

netvox R718PB15A Bedienungsanleitung

netvox

netvox R816B Bedienungsanleitung

netvox

netvox R718F2 Bedienungsanleitung

netvox

netvox R718B1 Series Bedienungsanleitung

netvox

netvox R311DA Bedienungsanleitung

netvox

netvox R718CK2 Bedienungsanleitung

netvox

netvox R718LB2 Bedienungsanleitung

netvox

netvox R718PA11 Bedienungsanleitung

netvox

netvox R718J Bedienungsanleitung

netvox

netvox R718G Bedienungsanleitung

netvox

netvox R809A Bedienungsanleitung

netvox

netvox R313K Bedienungsanleitung

netvox

netvox R718UBB Series Bedienungsanleitung

netvox

netvox RA02C Bedienungsanleitung

netvox

netvox R718PA Series Bedienungsanleitung

netvox

netvox R311LA Bedienungsanleitung

netvox

netvox R311B Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

netvox Z809B Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken