Novus NVIP-5DN7560H/IRH-2P Bedienungsanleitung

U s e r ’s m a n u a l

( s h or t f or m )

NVIP-5DN7560H/IRH-2P

NVIP-5DN7560H/IRH-2P User’s manual ver.1.0 (short form)

EMC (2004/108/EC) and LVD (2006/95/EC ) Directives

CE Marking

Our products are manufactured to comply with requirements of the following directives and national regulations

implementing the directives:

Electromagnetic compatibility EMC 2004/108/EC.

Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as

75VDC and 1500VDC.

WEEE Directive 2002/96/EC

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European 1000VAC Directive on Waste Electrical and Electronic

Equipment (2002/96/EC) and further amendments. By ensuring this product is disposed of correctly, you will

help to prevent potential negative consequences for the environment and human health, which could otherwise

be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be

treated as household waste. It shall be handed over to the applicable collection point for used up electrical and

electronic equipment for recycling purpose. For more information about recycling of this product, please contact

your local authorities, your household waste disposal service or the shop where you purchased the product.

RoHS Directive 2002/95/EC

Out of concern for human health protection and friendly environment, we assure that our products

falling under RoHS Directive regulations, regarding the restriction of the use of hazardous

substances in electrical and electronic equipment, have been designed and manufactured in

compliance with the above mentioned regulations. Simultaneously, we claim that our products have

been tested and do not contain hazardous substances whose exceeding limits could have negative

impact on human health or natural environment

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self

installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices

during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN

USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT DOES

NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE

CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR

THE RESULTS OF SUCH AN ACTION.

IMPORTANT SAFEGUARDS AND WARNINGS

NVIP-5DN7560H/IRH-2P User’s manual ver.1.0 (short form)

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH

THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER

-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL

MAY OPEN THE UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is

necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is

forbidden;

7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,

damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted

by qualified personnel with proper authorization, in accordance with this user’s manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera

from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

Due to the product being constantly enhanced and optimized, certain parameters and functions described in the

manual in question may change without further notice. We strongly suggest visiting the www.novuscctv.com

website in order to access the newest manual

Data included in the following user’s manual is up to date at the time of printing. AAT Holding Sp z o.o. holds

exclusive rights to modify this manual. The producer reserves the rights for device specification modification

and change in the design without prior notice.

NVIP-5DN7560H/IRH-2P User’s manual ver.1.0 (short form)

TABLE OF CONTENTS.....................................................................................................4

1. FOREWORD INFORMATION .....................................................................................5

1.1. General Characteristics........................................................................................5

1.2. NVIP-5DN7560H/IRH-2P tech specification ....................................................6

1.3. Camera dimension ..............................................................................................7

1.4. Package contents..................................................................................................8

2. START-UP AND INITIAL IP CAMERA CONFIGURATION .................................9

2.1. Description of connectors and control tools ........................................................9

2.2. NVIP-5DN7560H/IRH-2P mounting ................................................................10

2.3. Desiccant mounting guide ................................................................................11

2.4. Starting the IP camera........................................................................................12

2.5. Initial configuration via the Web browser.........................................................13

3. NETWORK CONNECTION UTILIZING WEB BROSWER ................................14

3.1. Recommended PC specification for web browser .............................................14

3.2. Connection with IP camera via the Internet Explorer ........................................14

3.3. Connection with IP camera via the other browser .............................................16

4. WWW INTERFACE - WORKING WITH IP CAMERA.........................................18

4.1. Displaying live pictures......................................................................................18

5. ELECTRIC CONNECTORS AND ACCESORIES .................................................20

5.1. Connecting power supply to the camera. ..........................................................20

5.1. Connecting alarm input and output ....................................................................20

5.2. SD card installation ...........................................................................................21

6. RESTORING FACTORY DEFAULTS .....................................................................22

6.1. Restoring software factory defaults....................................................................22

6.2. Restoring hardware factory defaults in IP cameras...........................................22

TABLE OF CONTENTS

NVIP-5DN7560H/IRH-2P User’s manual ver.1.0 (short form)

1. FOREWORD INFORMATION

1.1. General Characteristics

Mechanical IR cut filter

IR operation capability

Imager resolution: 5.0 megapixels

Min. Illumination: from 0.02 lx/F=1.4 (0 lx - IR On)

Wide Dynamic Range (WDR)

Digital Slow Shutter (DSS)

Digital Noise reduction (DNR)

Lens with remote focal and focus control 3.3 ~ 10.5 mm (F1.4)

Built-in IR LED - 24 pcs.

Privacy zones: 5

1 alarm input and output

Built-in webserver: video and audio compression and real-time network transmission

Compression: H.264, M-JPEG

Video processing resolution: - 2592 x 1944 - 2048 x 1536 - 1920 x 1080 - 1280 x 1024 -

1280 x 720 - 1024 x 768 - 800 x 600 - 720 x 576 - 640 x 480 - 352 x 288

4 streams: compression, resolution, speed and quality defined individually for all video streams

RTP/RTSP protocol support for video transmission

Network connection control and IP address check function

Pre- & post-alarm functions - video recording in AVI format

Schedule recording function

Hardware motion detection

Bidirectional audio transmission

Micro SD/SDHC card support

Diverse definition of system reactions to alarm events: e-mail with attachment, saving file on FTP

server, NAS, alarm output trigger, saving file on micro SD/SDHC card, HTTP notification

Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,

playback and remote IP devices administration

IP 66

Built-in heater

Power supply: 24 VAC/PoE+ (Power over Ethernet)

FOREWORD INFORMATION

NVIP-5DN7560H/IRH-2P User’s manual ver.1.0 (short form)

1.2. NVIP-5DN7560H/IRH-2P specification

FOREWORD INFORMATION

NVIP-5DN7560H/IRH-2P

IMAGE

Pick-up Element 5 MPX, CMOS imager, 1/2.5”

Number of Effective Pixels 2592 (H) x 1944 (V)

Min. Illumination 0.2 lx/F=1.4 - color mode DSS,

0.02 lx/F=1.4 - B/W mode DSS, 0 lx (IR on)

Digital Slow Shutter (DSS) Up to 1 s

Wide Dynamic Range (WDR) Yes

Digital Noise Reduction (DNR) Yes

LENS

Type Lens with remote focal and focus control, f=3.3 ~ 10.5 mm (F1.4)

Angle of View (H) 94° - 35°

DAY/NIGHT

Type Mechanical IR cut filter

Switching Mode Auto/manual/light sensor/smart/external/time

NETWORK

Stream Resolution

2592 x 1944, 2048 x 1536 (QXGA), 1920 x 1080 (Full HD), 1280 x 1024 (SXGA),1280 x 720

(HD), 1024 x 768 (XGA), 800 x 600 (SVGA), 720 x 576 (D1), 640 x 480 (VGA),

352 x 288 (CIF)

Frame Rate

12 fps for 2592 x 1944,

15 fps for 2048 x 1536,

30 fps for 1920 x 1080 and lower resolutions

Multistreaming Mode 4 streams

Video/Audio Compression H.264, M-JPEG/G.711, G.726

Network Protocols Support ONVIF (2.4/Profile S), HTTP, TCP/IP, IPv4/v6, UDP, HTTPS, Multicast, FTP, DHCP,

DDNS, NTP, RTSP, RTP, UPnP, SNMP, QoS

PC Software NOVUS NMS, Internet Explorer

OTHER FUNCTIONS

OSD IE browser, Polish, English, Russian and others

Privacy Zones 5

Motion Detection Yes

Prealarm/Postalarm 20 frames or 3 s/20 frames or 9999 s

System Reaction to Alarm Events E-mail with attachment, saving file on: FTP server, NAS server, micro SD/SDHC card, output

activation, HTTP notification

IR LED

Number 24

Range 25 m

Angle 90°

INTERFACES

Video Output 1 x BNC, 1.0 Vp-p, 75 Ohm - maintenance only

Audio Input/Output 1 x Jack (3.5 mm)/1 x Jack (3.5 mm)

Alarm Input/Output 1/1

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Memory Card Slot micro SD

INSTALLATION PARAMETERS

Dimensions (mm) 90 (Ø) x 270 (L)

Weight 1.1 kg

Enclosure Aluminium, white, mounting bracket and sunshield in-set included

Power Supply PoE+, 24 VAC

Power Consumption

9 W,

12 W (IR on),

29 W (heater and IR on)

Operating Temperature -40°C ~ 50°C

Built-in Heater Yes

Degree of Protection IP 66

NVIP-5DN7560H/IRH-2P User’s manual ver.1.0 (short form)

FOREWORD INFORMATION

1.3. Camera dimensions

NVIP-5DN7560H/IRH-2P User’s manual ver.1.0 (short form)

1.4. Package contents

After you open the package make sure that the following elements are inside:

IP camera

230 VAC / 12 VDC power supply

Accessories bag

Short version of user’s manual

CD containing manual and software

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

1.4. Package contents

After you open the package make sure that the following elements are inside:

IP camera

Accessories bag

Short version of user’s manual

CD containing manual and software

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

FOREWORD INFORMATION

NVIP-5DN7560H/IRH-2P User’s manual ver.1.0 (short form)

2. START-UP AND INITIAL IP CAMERA CONFIGURATION

2.1. Description of connectors and control tools

NVIP-5DN7560H/IRH-2P

1. Lens

2. Light Sensor

3. Mounting screw

4. Port Ethernet 100 Mb/s (RJ-45 connector)

5. Power socket

6. Alarm input/output

7. Audio output

8. Audio input

9. BNC video output

START-UP AND INITIAL CAMERA CONFIGURATION

Power socket 24VAC

+ 24V(+)

Earth ground

─24V(-)

NVIP-5DN7560H/IRH-2P User’s manual ver.1.0 (short form)

2.2. NVIP-5DN7560H/IRH-2P mounting

To mount a camera please follow the instructions below:

Put the bracket to the wall in a desired mounting place (with cable hole). Taking the bracket’s

base screw holes as a pattern, mark future drilling holes for screws using a punch.

Drill holes in accordance with previously done markings and base hole placement.

Mount the camera with bracket on the ceiling/wall with three supplied self tapping screws.

Adjust the camera vertical position using the “A” screws.

Adjust camera position loosening the horizontal adjustment screw (“B” screws).

Adjust camera rotation loosening the adjustment screw (“C” screws).

NOTE:

Please note that the wall or ceiling must have enough strength to support the IP Camera.

Lens Adjustment

Unscrew the screw “D” on the Camera Housing

Remove “E” the Front Housing in the direction pointed by arrow.

Adjust Zoom and Focus loosening the zoom/focus blocking screw.

Put front housing on to camera.

Block the “D” screw.

NOTE:

In order to obtain declared degree of protection please seal the camera bracket to prevent water

getting inside. Furthermore, when installing the bracket on rough/uneven surfaces, please

additionally seal the junction with appropriate sealing mass. Please pay special attention to any

mounting holes and if they are a loop-through ones, seal them too.

START-UP AND INITIAL CAMERA CONFIGURATION

B C D

Inhaltsverzeichnis

Sprachen:

Andere Novus Sicherheitskamera Handbücher

Novus

Novus NVDN-601V/IR-white Bedienungsanleitung

Novus

Novus NVIP-5DN3614V/IR-1P Bedienungsanleitung

Novus

Novus NVIP-5VE-4511/FWLAD Bedienungsanleitung

Novus

Novus NVIP-2V-4202 Bedienungsanleitung

Novus

Novus NVIP-2DN3034V/IR-1P Bedienungsanleitung

Novus

Novus NVIP-3DN7030SD-2P Bedienungsanleitung

Novus

Novus NVAHD-2DN3201MV/IR-1-II Bedienungsanleitung

Novus

Novus NVIP-4DN2004V/IR-1P Bedienungsanleitung

Novus

Novus NVIP-5VE-6202M Bedienungsanleitung

Novus

Novus NVIP-4VE-6201/WL-II Bedienungsanleitung

Novus

Novus NVIP-4DN2004H/IR-1P-II Bedienungsanleitung

Novus

Novus NVIP-5VE-4202 Bedienungsanleitung

Novus

Novus NVIP-4H-6201-II Bedienungsanleitung

Novus

Novus NVIP-2VE-6232/WL-II Bedienungsanleitung

Novus

Novus NVIP-8VE-4511/FWLAD Bedienungsanleitung

Novus

Novus NVC-10BD Bedienungsanleitung

Novus

Novus NVIP-2V-6401 Bedienungsanleitung

Novus

Novus NVIP-5VE-4202M Bedienungsanleitung

Novus

Novus NVIP-4DN2004H/IR-1P Bedienungsanleitung

Novus

Novus NVAHD-1DN3105V/IR-1 Bedienungsanleitung

Novus

Novus NVIP-2DN3037V/IR-1P Bedienungsanleitung

Novus

Novus NVIP-8H-4511/FWLAD Bedienungsanleitung

Novus

Novus NVIP-TDN5410C/MPX1.0 Bedienungsanleitung

Novus

Novus NVIP-5VE-6401/F Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung