Olympus USPM-RUIII Series Bedienungsanleitung

PV6088-F4E017

Optical Measuring Instrument

USPM-RUIII series

USPM3-100、USPM3-200

Hardware Operation Manual

Before you get started

Thank you for purchasing Olympus Lens Spectral Reflectivity Measurement

USPM3-100/USPM3-200. Before you start using it, please be sure to read this operation

manual carefully, and then, store it in a readily accessible safe place, so that it can be

referred to at any time you need it. Our warranty card is attached to the back of the

manual. Complete the required entries, and then store the card in a safe place.

PV6088-F4E017

PREFACE

How to carry

For how to carry this product, refer to 2.2 How to carry and install the product.

How to clean

For how to clean this product, refer to 2.3 How to clean.

Usage environment

Use this product in an environment that conforms to the specification.

For the specification of usage environments, refer to 9. SPECIFICATIONS.

About the lamp house

Though heavily dependent on the usage conditions (ambient temperature and

humidity, supply voltage, period of lighting, etc.), the useful life of the lighting device

(lamp house) * assumes either short one of for approximately three years（In the case

of the use of approximately eight hours a day）or approximately 15,000 hours .

*The above statement does not guarantee freedom from failures or repair at no

charge during the service life.

* Depending on the usage conditions, there is a possibility of aging degradation in a

shorter period.

Inspect the lamp house according to Appendix: Checklist for inspection of the

lighting device (lamp house) until the lamp house reaches the end of its useful life.

Should any unexpected incident occur (e.g., smoke) during use, turn off the power

immediately and contact the sales representative where you purchased the unit or our

sales department. Regular inspection is recommended, in order to achieve safe use

and reduce downtime.

About the personal computer (hereinafter "computer")

We (Olympus) will take no responsibility for any and all damage arising out of the use

or malfunction of the unit, including, but not limited to, any damage to the data stored

in your personal computer(s). Please make a backup copy of your computer system

and keep it in a safe place. (Olympus does not provide any backup support.)

We assure the quality of the unit when it is shipped from our factory. No malfunction

or disability due to any change in the environment settings of the computer by you

(e.g., any change in the BIOS) or installation of any other applications are covered by

the quality assurance of Olympus.

When there is only a small amount of free space in the computer’s hard disk drive

this may make the data processing take longer or even cause errors. Delete

unneeded data files regularly. For how to delete data files, refer to the operating

system manual.

NEVER delete or rename any folders already included on the hard disk drive of the

computer in the configuration at the set up. Otherwise, the software may become no

longer usable.

PV6088-F4E017

SAFETY PRECAUTIONS

About safety

If this product is used in a way that is not described in this document, safety is not

guaranteed, in addition to the risk of failure. Always adhere to the instructions given here.

Description of Symbols and Terms Used in This Instruction Manual

The following symbols and terms are introduced in connection with possibly hazardous

operations and practices according to the importance of the involved hazards. Pay utmost

attention to these symbols and terms to ensure the safe use of the device.

Symbols denoting prohibition (prohibited actions)

Symbols denoting obligation (mandatory actions)

Symbols denoting caution

Failure to follow the instructions associated with this symbol could

cause an accident, such as fire, electric shock, etc., which could

result in serious injury to the user or death.

Failure to follow the instructions associated with this symbol could

result in an accident, such as electric shock which could cause

injury to the eyes or body of the user, or result in damage to the

device.

Mandatory

Unplugged

PV6088-F4E017

Symbols relating to safety

Lens Spectral Reflectivity Measurement USPM3-100/USPM3-200 contains the following

symbols.

Handle the product safely, keeping in mind the significance of these marks.

Symbols on the package

The package has the following symbols:

Indicates this side up.

Indicates that the box should be protected from rain.

Indicates that the items inside are fragile and that the package should be

handled with care.

Indicates the compatibility with China RoHS.

Symbols

Description

Avoid touching the surface since it is hot.

There is a risk of burns.

Indicates an unspecified, common danger. Follow the instruction in

the operation manual or that shown with the mark.

An inter-switching push button turns on/off the main switch.

PV6088-F4E017

Do not install the device in a location that is frequently exposed to dust,

moisture, oily fumes, or steam.

If the device is installed in any of aforementioned environments, fire or

electric shock hazards may result. To install the device, avoid a location

exposed to direct sunlight, location at an unusually high temperature, such

as near a space heater, heating unit, etc., or at a very low temperature, or a

location with high humidity, heavy dirt or dust.

Do not introduce water or a foreign object into the device.

Introducing water or a foreign object into the device will result in a fire or

electric shock hazard. If water or a foreign object is found to have been

accidentally introduced into the device, immediately switch off the device.

Unplug the power cord. Then contact the vendor from whom the device was

purchased.

Do not modify or disassemble the part.

Unauthorized disassembling or modifying of the system might cause fire,

electric chock, or injury. If any abnormality occurs as a result of

unauthorized modification of the system, such as the failure of the piezo

element, inactivation of the computer display, inactivation of the computer,

blown fuse, development of unusual odor and sounds, etc., power off the

system instantly. Remove the power cord from the wall outlet. Contact our

sales department for repair. Troubleshooting by an unauthorized person,

which is very dangerous, is strictly prohibited.

Do not block the ventilation hole for heat radiation of the light source!

The light source (U-LH100L-3) becomes very hot while the lamp is on. Be

careful not to block the ventilation hole for heat radiation. If the lamp is

turned on with the ventilation hole blocked, it may lead to fire.

Set up the main body 10cm or more apart from walls!

The light source (U-LH100L-3) becomes very hot while the lamp is on. Set it

up with the main body and the wall 10cm or more apart. It may lead to fire.

If the following cautions are not observed, there

may be a possibility of fire, electric shock, etc.,

which could result in serious injury to the user or

death.

PV6088-F4E017

Do not touch on the light source. Moreover, do not put the thing.

The light source (U-LH100L-3) becomes very hot while the lamp is on. Do

not touch on the light source. Moreover, do not put the thing. It may lead to

the burn and a fire.

Do not cover with the vinyl cover etc. until the light source gets cold.

The light source (U-LH100L-3) becomes very hot while the lamp is on. Do

not cover with the vinyl cover etc. until the light source gets cold. It may lead

to a fire.

Do not handle the device with wet hands.

If the user handles the device with wet hands, or plugs or unplugs the power

cord using wet hands, severe electric shock could result.

Operate the device with the specified power!

Input voltage of the Control Box is configured to 100–120 V or 220–240 V,

depending on the shipment destination. There is a nameplate indicating the

voltage setting on the back surface. Use this product within the voltage

range. Otherwise there is a risk of damage or fire. Make sure to contact our

service department when you move it into a place having a different voltage

range.

Ground the unit securely!

Connect the earth terminal of a three-terminal outlet to the ground for safety.

Imperfect grounding may cause electric shocks. Without grounding, the

intended electrical safety is not achieved.

Always use the supplied cables.

Always usee supplied cables. Using any cables other than those supplied

may cause malfunctions due to internal and/or external noise.

PV6088-F4E017

Always use the supplied power cord.

Employing any other cables than those supplied may cause failures due to

internal and/or external noises.

The supplied cables are not usable with any other devices.

When no power cord is attached to the product, refer to the “Precautions for

proper use of the power cord”to choose a proper power code for the unit.

Replacement of fuses

Before replacing a fuse, turn off the power and unplug the power cord so as

to avoid electric shocks.

Rating of the fuse: 250 V AC, 3.15 A

Type of the fuse: Time lag , High breaking capacity type

Size of the fuse: φ5.2 mm 20 mm

Replacement of the lamp

Use the specified lamp for replacement. Otherwise there is a risk of damage

or fire.

Compatible lamp: 12 V 100 W (7023 from PHILIPS)

Do not install the device in an unstable location.

If the device is installed on an unstable platform, an inclined floor, or a floor

lacking sufficient rigidity, the device could fall or collapse, which might cause

bodily injury to the user or others in the area. Prior to installation, thoroughly

check the rigidity and flatness of the place where the device is to be

installed.

Do not change the lamp outright after turning it off!

To change the lamp because it was burnt out, or for any other reason, wait

till after it has cooled down enough, because it is very hot immediately after

switched off.

Failure to conform to the following cautions may cause injury or

physical damage to peripheral devices.

PV6088-F4E017

Exert good caution in focusing!

When bringing the reflection sample surface into focus, use good caution

not to allow the objective to inadvertently hit the sample surface.

Measure the sample at a normal temperature

If the sample temperature is higher than normal, the sample may transform

or give damaged to the stage..

FCC Warning

If the user changes or modifies a device without first receiving permission

from the entity responsible for ensuring the device complies with FCC rules,

the user forfeits the right to operate the device.

PV6088-F4E017

Position of the warning label

Warning labels

The lamp house, which becomes hot, has a warning label (back of the unit).

Make sure to adhere to the instructions. If the label is missing, or it gets dirty

or starts to peel, contact your supplier for a replacement.



Confirm that a lamp turns off the light!

Please confirm that a lamp turns off the light by all means before excluding

a lamp house

Indicates precautions about

replacement of lamps.

Warning label

This product corresponds to RISK GROUP2 in a UV range (200-400nm) and a blue light

range (300-700nm) based on IEC62471-2.

In addition, this product corresponds to RISK GROUP1 in the IR range (780-3000nm).

PV6088-F4E017

TABLE OF CONTENTS

1. PURPOSES AND FEATURES ·····························11

2. CARRYING AND INSTALLATION·························12

3. NAMES AND FUNCTIONS OF COMPONENT

PARTS ····························································15

4. ASSEMBLING AND CABLING ·····························22

5. MEASURING METHOD·····································25

6. PRINCIPLE OF MEASUREMENT·························28

7. REPLACEMENT OF FUSES································29

8. REPLACEMENT OF LAMP································30

9. SPECIFICATIONS ·············································31

10. LAWS AND REGULATIONS ······························33

11. QUALITY ASSURANCE (WARRANTY SHEET)·····35

APPENDIX·····························································37

○Precautions for proper use of the power cord

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Olympus Messgerät Handbücher

Olympus

Olympus U-GAN Bedienungsanleitung

Olympus

Olympus DS-3000 Bedienungsanleitung

Olympus

Olympus CIX100 Bedienungsanleitung

Olympus

Olympus OmniScan MX Bedienungsanleitung

Olympus

Olympus USPM-RU-W Series Bedienungsanleitung

Olympus

Olympus TERRA II Bedienungsanleitung

Olympus

Olympus OMCL-AC200TN-C3 Bedienungsanleitung

Olympus

Olympus 37DL PLUS Bedienungsanleitung

Olympus

Olympus Vanta L Series Bedienungsanleitung

Olympus

Olympus USPM-RU-W Series Bedienungsanleitung

Olympus

Olympus OMCL-AC240TS-R3 Bedienungsanleitung

Olympus

Olympus 27MG Bedienungsanleitung

Olympus

Olympus BTX III Bedienungsanleitung

Olympus

Olympus EPOCH 650 Bedienungsanleitung

Olympus

Olympus BIX III Bedienungsanleitung

Olympus

Olympus DELTA 50 Bedienungsanleitung

Olympus

Olympus Magna-Mike 8600 Bedienungsanleitung

Olympus

Olympus STM7-AF Bedienungsanleitung

Olympus

Olympus Vanta iX Series Bedienungsanleitung

Olympus

Olympus WS 100 - 64 MB Digital Voice Recorder Bedienungsanleitung

Olympus

Olympus Vanta L Series Bedienungsanleitung

Olympus

Olympus 45MG Bedienungsanleitung

Olympus

Olympus ORBEYE OME-V200 Bedienungsanleitung

Olympus

Olympus OMCL-AC240TN-C3 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung