Olympus BX3-URA Bedienungsanleitung

INSTRUCTIONS

This instruction manual is for the Olympus Reflected Fluorescence System. To ensure the safety,

obtain optimum performance and to familiarize yourself fully with the use of this system, we

recommend that you study this manual thoroughly before operating the microscope. Retain this

instruction manual in an easily accessible place near the work desk for future reference.

A X 7 8 8 8

BX3-URA

BX3-RFAS

U-LH100HGAPO

U-LH100HG

U-RFL-T

U-AN-2

BX3-25ND6

BX3-25ND25

REFLECTED

FLUORESCENCE

SYSTEM

This device complies with the requirements of both directive 2004/108/EC concerning

electromagnetic compatibility and directive 2006/95/EC concerning low voltage. The CE marking

indicates compliance with the above directives.

CONTENTS

Correct assembly and adjustments are critical for the reflected fluorescence system to exhibit its full performance. If you are

going to assemble the reflected fluorescence system yourself, please carefully read section 8, “ASSEMBLY” (pages 24 to 27)

IMPORTANT -- Be sure to read this section for safe use of the equipment. -- 1-3

4-6

7,8

20-22

9-19

24-27

1 NOMENCLATURE

5 TROUBLESHOOTING GUIDE

4 SIMULTANEOUS FLUORESCENCE OBSERVATIONS

8 ASSEMBLY -- See this section for the replacement of the light bulb. --

9 LAMP HOUSING INSPECTION SHEET

· BX3-RFAS

· BX3-URA

1General Precautions for Observation....................................................................................................................... 9

2Selecting the Fluorescence Mirror Unit................................................................................................................. 9

3Turning the Power Supply Unit On..............................................................................................................................11

4Centering the Field Iris Diaphragm.............................................................................................................................11

5Centering the Aperture Iris Diaphragm.................................................................................................................12

6Centering the Mercury Burner ...........................................................................................................................................13

Simultaneous Reflected Fluorescence and Phase Contrast Observations

...........................18

8-1 Assembly Diagram.......................................................................................................................................................................... 24

8-2 Detailed Assembly Procedures..................................................................................................................................... 25

7Mounting the ND Filters..............................................................................................................................................................16

8Attaching the Light Shield Sheet ...................................................................................................................................17

nPROPER SELECTION OF THE POWER SUPPLY CORD.......................................................... 29,30

REFLECTED FLUORESCENCE OBSERVATION PROCEDURE

3 USING THE CONTROLS

6 SPECTRAL CHARACTERISTICS OF FILTERS

7 SPECIFICATIONS

Simultaneous Reflected Fluorescence and Transmitted Light Nomarski

Differential Interference Contrast (DIC) Observations

......................................................................................18

SAFETY PRECAUTIONS

IMPORTANT

1. This system is composed of precision instruments. Handle it with care and avoid subjecting it to sudden or severe

impact.

2. The ultrahigh-pressure mercury burner used should be the USH-103OL that is a DC mercury burner manufactured and

supplied by Olympus.

3. Make sure that a mercury burner is attached and that cables are plugged in firmly.

4. The inside of the lamp housing is very hot and hazardous during lighting and for about 10 minutes after turning off. Do

not open the lamp housing in this period. (Page 11)

5. Do not apply excessive force to the stoppers which are provided for some functions. Otherwise, the stopper or equipment

may be damaged.

6. Do not attempt to open, disassemble or modify the power supply unit because it includes high voltage parts inside.

7. Always use the power cord provided by Olympus. If no power cord is provided, please select the proper power cord by

referring to the section “PROPER SELECTION OF THE POWER SUPPLY CORD” at the end of this instruction manual. If

the proper power cord is not used, product safety and performance cannot be guaranteed.

Before plugging the power cord to the power outlet, make sure that the main switch of the power supply unit is set to

“ ” (OFF).

8. To ensure safety, be sure to ground the power supply unit. Otherwise, Olympus can no longer warrant the electrical safety

performance of the system.

9. Before opening the lamp housing for replacement of the burner or any other internal part, set the main switch to “ ”

(OFF), then unplug the lamp housing connection cable from the power supply unit, and wait for more than 10 minutes

until the lamp housing cools down.

This system employs a UIS2 (Universal Infinity System 2) optical design, and should be used only with

UIS2 microscopes, eyepieces, objectives and condensers for the BX3 series. (Some of the objectives/

eyepieces for the UIS series are also usable. For details, please consult Olympus or the catalogues.)

Less than optimum performance may result if inappropriate accessories are used.

Please also read the separately attached instruction manuals listed below to obtain comprehensive understanding of the

system operating procedures.

Manual name Main contents

Reflected Fluorescence System

(This manual)

Reflected fluorescence observation procedure using the BX3-URA or BX3-RFAS vertical

illuminator and the reflected light observation procedure using the BX3-URA.

Information Readout System

(U-CBS)

Management of information acquired from the BX3-RFAS cube and U-D7RES

objective.

Microscope

(BX43, BX53) Operating procedures of each microscope.

Power Supply Unit

(U-RFL-T)

Operating procedures of the power supply unit for the lamp housing for mercury

burner.

10. The top panel of the lamp housing becomes very hot during operation. To prevent fire hazard, do not block the ventilation

through the top panel.

11. The standard service life of the lamp housing is eight (8) years of use or 20,000 hours of total power ON period, whichever

is the shorter period.

For details, see Inspection Sheet on page 28.

Safety Symbols

The following symbols are found on the microscope. Study the meaning of the symbols and always use the equipment

in the safest possible manner.

Symbol Explanation

Indicates the presence of high voltage (1 kV or more). Take caution to guard against electric

shock.

Indicates that the surface becomes hot, and should not be touched with bare hands.

Indicates a non-specific general hazard. Follow the description given after this symbol or in

instruction manual.

Indicates that the main switch is ON.

Indicates that the main switch is OFF.

Caution indications

Caution indications are placed at parts where special precaution is required when handling and using the System. Always

heed the warnings.

Caution indication

position

· Lamp housing for mercury burner

(U-LH100HG, U-LH100HGAPO)

· Illuminator

(BX3-URA, BX3-RFAS)

· ND filter high voltage]

(BX3-25ND6, BX3-25ND25)

· ND filter slider

(provided with BX3-RFAS)

· Power supply unit

(U-RFL-T)

[Caution against

high temperature]

[Caution against

high voltage]

1 Getting Ready

1. This manual pertains only to the reflected fluorescence system. Before using this system together with the BX3 microscope

and associated options, make sure that you have carefully read and understood their manuals, and understand how the

system should be operated together.

2. The reflected fluorescence system is composed of precision instruments. Handle it with care and avoid subjecting it to

sudden or severe impact.

3. Do not use the system where it is subjected to direct sunlight, high temperature and humidity, dust or vibrations.

4. To allow heat from the unit to dissipate well, reserve clearances of at least 10 cm around the lamp housing and power

supply unit.

5. The power cord can also be used to cut the power supply in case of emergency. To make this possible, the power supply

unit should be installed so that the power cord connector (on the rear of the power supply unit) or the power outlet is

easily accessible for unplugging in case of emergency.

6. Before igniting the burner, make sure that a mercury burner is attached and the cords are connected properly.

7. Avoid turning the lamp on-off repeatedly as this reduces the burner life considerably. The average service life of a mercury

burner is about 300 hours (USH103OL) with operating cycles of 2-hour ON and 30-minute OFF.

2 Maintenance and Storage

1. To clean the lenses and other glass components, simply blow dirty away using a commercially available blower and

wipe gently using a piece of cleaning paper (or clean gauze).

If a lens is stained with fingerprints or oil smudges, wipe it gauze slightly moistened with commercially available absolute

alcohol.

Since the absolute alcohol is highly flammable, it must be handled carefully.

Be sure to keep it away from open flames or potential sources of electrical sparks --- for example, electrical

equipment that is being switched on or off.

Also remember to always use it only in a well-ventilated room.

2. With any part of the system other than glass components gets dirty, do not use organic solvents but wipe it with a clean

cloth. If the part is extremely dirty, use a lint-free, soft cloth slightly moistened with a diluted neutral detergent.

3. Do not disassemble or modify the parts of the system unless when instructed to do so in this manual. Otherwise,

malfunction, reduced performance or accident may result.

4. The mercury burner has a service life period of 300 hours (USH-103OL, HBO103W/2). When the hour counter on the power

supply unit indicates this value, set the main switch to “ ” (OFF) and wait for more than 10 minutes before replacing

the mercury burner (Page 26). Unlike electric bulbs, the mercury burner seals high-pressure gas inside. If it continues to

be used after the service life has expired, the glass tube may eventually explode due to accumulated distortion.

5. When not using the microscope, be sure set the main switch to “ ” (OFF). After confirming that the lamp housing has

cooled down sufficiently, cover the microscope with the dust cover for storage.

6. When disposing of the system, always follow your local regulations and rules. If you have any question, contact

Olympus.

3 Caution

If the system is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition, the

system equipment may also be damaged. Always use the system as outlined in this instruction manual.

The following symbols are used to set off text in this instruction manual.

: Indicates a potentially hazardous situation which, if not avoided, may result in minor

or moderate injury or damage to the equipment or other property. It may also be used

to alert against unsafe practices.

} : Indicates commentary (for ease of operation and maintenance).

CAUTION

1NOMENCLATURE

Mirror unit turret

Universal Reflected Illuminator

BX3-URA

Apo Lamp Housing for 100 W Mercury Burner U-LH100HGAPO

Lamp Housing for 100 W Mercury Burner U-LH100HG

Mirror unit inscription

pocket (Page 25)

Shutter knobs

(Provided on both sides.)

(Page 11)

\: Shutter OPEN

{: Shutter CLOSE

Field iris diaphragm knob (Page 11)

Analyzer insertion slot (Page 18)

Field iris diaphragm centering screws (Page 11)

x2 screws.

Collector lens focusing knob (Page 13,14)

Burner centering knobs

(Page 13,14)

Mirror focusing screw

(Page 15)

On the rear of the

lamp housing.

ND filter insertion slots (Page 16)

Provided on both sides.

Aperture iris diaphragm

centering screws (Page 12)

x2 screws

Aperture iris diaphragm knob

(Page 12)

Coded Fluorescence Illuminator

BX3-RFAS

Lamp Housing for 100 W Mercury Burner

U-LH100HGAPO

U-LH100HG

Mirror unit inscription

pockets (Page 25)

Mirror unit turret

Shutter knobs (Provided on both sides.)

(Page 11)

\: Shutter OPEN

{: Shutter CLOSE

ND filter slider insertion slot

(Page 16)

Insertion from right side.

Aperture iris diaphragm knob

(Page 12)

Field iris diaphragm knob (Page 11)

Field iris diaphragm centering screws (Page 11)

Analyzer inlet

Stopper

ND filter slider for BX3-RFAS

Engaged filter name inscription

Stopper

Collector lens focusing knob Burner centering knobs

Mirror focusing screw

(On the rear of the lamp housing.)

Fluorescence Mirror Units

Indicator sheets

}Up to eight fluorescence mirror units can be mounted on the BX3-URA

or BX3-RFAS.

}It is recommended that you use the U-FF dummy mirror unit (which does

not contain a filter) when making your original fluorescence mirror unit

(page 27).

Blank indicator sheets provided with the illuminator can be used to write

the names of original fluorescence mirror units.

Power Supply Unit

U-RFL-T/U-RX-T

ND Filters

BX3-25ND6, BX3-25ND25

Centering Target

U-CST

}For details, see the instruction manual provided with the U-RFL-T/U-RX-T.

}Use the U-RFL-T when the light source is a mercury burner or use the U-RX-T when the light

source is a xenon burner.

Hour counter

Lamp ON LED

Main switch

I : ON

: OFF

Lamp housing connector

Power cord connector

REFLECTED FLUORESCENCE OBSERVATION PROCEDURE

Preparation

Set the main switch to “ I ” (ON) and wait for the

lamp brightness to stabilize (5 to 10 minutes

after ignition).

Engage the fluorescence mirror unit matching

the specimen in the light path.

Engage the objective in the light path and focus

on the specimen

Adjust so that the

entire field is uniform

and brightest.

Adjust the brightness

as required.

Engage an ND filter in the

light path as required.

Place the specimen on the stage.

}If you need simultaneous observation of reflected fluorescence observation with the phase contrast observation or

transmitted light Nomarski Differential Interference Contrast (DIC) observation, please read Chapter 4, “SIMULTANEOUS

FLUORESCENCE OBSERVATION”. (Page 18)

(Controls Used) (Page)

· Attach the fluorescence mirror unit and objective matching the observation method. (Pages 9 to 10)

· Center the mercury burner. (Pages 13 to 15)

Adjust the field iris diaphragm.

Adjust the aperture iris

diaphragm.

Observation

@Main switch (P.11)

2Slide holder

3X-/Y-axis knobs

4Mirror unit turret

5Revolving nosepiece

6Coarse/fine adjustment knobs

7ND filter (P.16)

8Collector lens focusing knob (P.13,14)

9Field iris diaphragm knob (P.11)

aAperture iris diaphragm knob (P.12)

bShutter knob (P.11)

BX3-URA BX3-RFAS

}Engage the shutter if you interrupt observation for a short time.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Olympus Mikroskop Handbücher

Olympus

Olympus BHA-P Bedienungsanleitung

Olympus

Olympus SZX10 Bedienungsanleitung

Olympus

Olympus BX53-P Bedienungsanleitung

Olympus

Olympus U-UVF248A Bedienungsanleitung

Olympus

Olympus K Betriebsanleitung

Olympus

Olympus SZ2-ILA Bedienungsanleitung

Olympus

Olympus SZX16 Bedienungsanleitung

Olympus

Olympus X-Tr Betriebsanleitung

Olympus

Olympus SLIDEVIEW VS200 Bedienungsanleitung

Olympus

Olympus VM Series Bedienungsanleitung

Olympus

Olympus CHA-P Bedienungsanleitung

Olympus

Olympus SZ61 Bedienungsanleitung

Olympus

Olympus POS Bedienungsanleitung

Olympus

Olympus DP73 Bedienungsanleitung

Olympus

Olympus CX31 Bedienungsanleitung

Olympus

Olympus BX53 Bedienungsanleitung

Olympus

Olympus U-CBS Bedienungsanleitung

Olympus

Olympus CK2 Bedienungsanleitung

Olympus

Olympus BHSU Montageanleitung

Olympus

Olympus CH2 Series Betriebsanleitung

Olympus

Olympus IX71 Bedienungsanleitung

Olympus

Olympus U-D7RES Bedienungsanleitung

Olympus

Olympus VANOX Betriebsanleitung

Olympus

Olympus BHTU-112 Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Leica

Leica FL560 Bedienungsanleitung