Olympus BX63 Bedienungsanleitung

INSTRUCTIONS

BX63

INTELLIGENT MICROSCOPE

This instruction manual is for the Olympus Intelligent Microscope Model BX63.

To ensure the safety, obtain optimum performance and to familiarize yourself fully with the use

of this microscope, we recommend that you study this manual thoroughly before operating the

microscope.

Retain this instruction manual in an easily accessible place near the work desk for future reference.

A X 7 9 3 3

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

In accordance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment,

this symbol indicates that the product must not be disposed of as unsorted municipal waste, but

should be collected separately.

Refer to your local Olympus distributor in EU for return and/or collection systems available in your

country.

CALIFORNIA USA ONLY

The touch panel controller of this product uses a Lithium Battery which contains Perchlorate Material -

special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate.

CONTENTS

Correct assembly and adjustments are critical for the microscope to exhibit its full performance. If you are going to assemble

the microscope yourself, please read section 9, “ASSEMBLY” (pages 39 to 44) carefully.

IMPORTANT -- Be sure to read this section for safe use of the equipment. -- 1-5

1 MODULE NOMENCLATURE 6

2 CONTROLS 7- 11

3 FLOW OF BRIGHTFIELD OBSERVATION 12,13

4 USING THE CONTROLS 14-32

4-2 Base............................................................................................................................................................................................................. 20,21

4-4 Stage (for the IX-SVL2)....................................................................................................................................................... 25,26

4-5 Observation Tube.................................................................................................................................................................... 27-29

4-6 Condenser.......................................................................................................................................................................................... 30,31

4-7 Immersion Objectives................................................................................................................................................................. 32

4-3 Stage (for the BX Series).............................................................................................................................................. 22-24

4-1 Touch Panel Controller.......................................................................................................................................................14-19

BX63

4-8 Objectives with Correction Collar.............................................................................................................................. 32

2Moving the Specimen

2Adjusting the Diopter

1Placing the Specimen

1Adjusting the Interpupillary Distance

1Centering the Condenser 2Compatibility of Objectives and

Condensers

Using the Filters

3Setting the Grounding

5Using the Light Shielding Sheet

3Using the Eye Shades 4Mounting the Eyepiece Micrometer

Disk

6Adjusting the Tilt

4Adjusting the X-Axis/Y-Axis Knob

Rotation Tension

5Selecting the Light Path of the

Trinocular Tube

2Using the Auxiliary Slide Holder

2Starting the System

Placing the Slide-Glass Specimen

1Basic Operations of Touch Panel

Controller

3Placing the 35 mm Dish Specimen

3System Setting

4Adjusting the X/Y-Axis Knob Rotation

Tension

4Selecting the Mode

1Using Immersion Objectives

5 CAMERA RECORDING 33

6 TROUBLESHOOTING GUIDE 34,35

7 SPECIFICATIONS 36,37

10 HALOGEN LAMP HOUSING INSPECTION SHEET 45

8 OPTICAL CHARACTERISTICS (UIS2 Series) 38

9 ASSEMBLY --

See this section for the replacement of the halogen light bulb.

-- 39-44

11 SET TYPE LIST 46-48

nPROPER SELECTION OF THE POWER SUPPLY CORD.......................................................... 49,50

2Selecting the Camera Adapter

Magnification

1System Chart

9-1 Assembly Diagram............................................................................................................................................................... 39-42

9-2 Detailed Assembly Procedures............................................................................................................................ 43,44

BX63

SAFETY PRECAUTIONS (Fig. 1)

1. If potentially infectious samples may be observed, use protective gloves or

other protective means to prevent the skin from contacting with samples

directly.

After observation, be sure to clean the portion contacted with samples.

· Moving this product is accompanied with the risk of dropping the

sample. Be sure to remove the sample before moving this product.

· In case the sample is damaged by erroneous operation, promptly take

the infection prevention measures.

· Follow the procedures described in Chapter “Getting Ready” (see

page 4) prior to using the accessories of this product. Otherwise, the

stability of the device will be lost and the dropped sample will cause

the possibility of infection.

· When you maintain the device which may have contacted with

potentially-infectious reagents, be sure to wear the protectors such as

gloves, or clean the device prior to operation.

· Before disposing of device contacted with potentially infectious samples,

be sure to follow the regulations and rules of your local government.

2 Be careful not to have your finger or hand caught by the space between

the revolving nosepiece arm @ and observation tube mount 2(Fig. 1).

3. Install the microscope on a sturdy, level table or bench.

4. Be careful not to tilt the microscope too much. Otherwise, the mobile

parts such as the light path selector knob may move.

5. Never insert metallic objects into the air vents of the microscope frame

as this could result in electrical shock, personal injury and equipment

damage.

6. Always use the power cord provided by Olympus. If no power cord is

provided, please select the proper power cord by referring to the section

“PROPER SELECTION OF THE POWER SUPPLY CORD” at the end of this

instruction manual. If the proper power cord is not used, product safety

performance cannot be warranted.

7. Always ensure that the grounding terminal of the microscope and that of

the wall outlet are properly connected. If the equipment is not grounded,

Olympus can no longer warrant the electrical safety performance of the

equipment.

This microscope employs a UIS2 (Universal Infinity System) optical design, and should be used only with

modules designed for the BX3-series and with UIS2 objectives/eyepieces.

For the applicable modules, please consult Olympus or the catalogues.) Less than optimum performance

may result if inappropriate accessories are used.

Configuration of Instruction Manuals

Since this microscope is expandable to a variety of systems, separate instruction manuals are prepared so

that the user has to read only the manuals according to the user’s own system.

Manual name Main contents

BX63 Transmitted light brightfield observation and touch panel

controller

BX3-CBH/U-MCZ Functions of the Control Box (incorporating power supply) and

the Controller

BX3-RFAA Motorized fluorescence illuminator

BX3-UCD8A Motorized universal condenser

BX3-SSU Scanning stage with ultrasonic

IMPORTANT

Fig. 1

Fig. 2

Operation Using the LED Lamp

Operation Using the Halogen Bulb

1. The surfaces of the lamp housing on the rear of the microscope will

become extremely hot during operation. When installing the microscope,

make sure to allow ample free space (10 cm or more) around and in

particular above the lamp housing for halogen bulb.

2. When installing the microscope, route the power cord away from the

lamp housing. Should the power cord come in contact with the hot lamp

housing, the power cord could melt and cause electric shock.

3. The standard service life of the lamp housing is eight (8) years of use or

20,000 hours of total power ON period, whichever is the shorter period.

For details, see Inspection Sheet on page 45.

4. To avoid potential shock hazards and burns when replacing the halogen

bulb, set the main switch 3to “ ” (OFF) and allow the lamp housing

| and bulb to cool before touching them (Fig. 2).

Designated halogen bulb 12V100WHAL-L (PHILIPS 7724)

Safety note on LED (Light Emitting Diode)

The LED incorporated in the LED lamp housing is a class 1 LED

product. The light emitted by LED is basically safe, but do not look at

the illumination light directly for an extended period to prevent your eye

from being injured

CLASS 1 LED PRODUCT

BX63

Safety Symbols

The following symbols are found on the microscope. Study the meaning of the symbols and always use the equipment

in the safest possible manner.

Symbol Explanation

Indicates that the surface becomes hot, and should not be touched with bare hands.

Indicates a non-specific general hazard. Follow the description given after this symbol or in

instruction manual.

Indicates that care is required against your finger or hand being caught.

Indicates that the main switch is ON.

Indicates that the main switch is OFF.

Caution indications

Caution labels are placed at parts where special precaution is required when handling and using the microscope. Always

heed the cautions.

Caution label

positions

Lamp housing

[Caution against high temperature]

Revolving nosepiece arm

[Caution against finger or hand being caught]

If a caution label is dirty or peeled off, contact Olympus for the replacement or other inquiry.

1 Getting Ready (Fig. 3)

Fig. 3

1. A microscope is a precision instrument. Handle it with care and avoid

subjecting it to sudden or severe impact. Also note that the microscope

does not have a waterproof construction.

2. Do not use the microscope where it is subjected to direct sunlight, high

temperature and humidity, dust or vibrations. (For the operating conditions,

refer to section 7, “SPECIFICATIONS”.)

3. When moving the microscope, carry it by holding the grasping part on the

rear of the arm and the front part of the base as shown in Fig. 3 (Weight:

Approx. 19 kg).

· Do not hold the rear cover plate because it is fragile.

· Before carrying, be sure to remove the dummy cover on the front

of the base as well as the specimen, eyepieces and filters so

that they will not drop during movement.

Also remove the modules from the microscope frame to reduce

the risk of heavy burden (Frame weight: Approx. 12 kg)

· To prevent damage to the microscope, never hold it by the stage,

stage fixing pillar or binocular tube, etc.

4. When the accessories of this product such as an intermediate attachment

are used, make sure that the system height does not exceed 1 meter (to

prevent the system from tipping over).

5. When the microscope needs to be packaged for forwarding to a

remote location, contact Olympus (to obtain advice for guaranteeing the

performance).

CAUTION

2 Maintenance and Storage

1. To clean the lenses and other glass components, simply blow dirt away using a commercially available blower and wipe

gently using a piece of cleaning paper (or with clean gauze).

If a lens is stained with fingerprints or oil smudges, wipe it gauze slightly moistened with commercially available absolute

alcohol.

Since the absolute alcohol is highly flammable, it must be handled carefully.

Be sure to keep it away from open flames or potential sources of electrical sparks --- for example, electrical

equipment that is being switched on or off, which could cause ignition of a fire.

Also remember to always use absolute alcohol only in a well-ventilated room.

2. Do not use organic solvents to clean the microscope components other than the glass components. To clean them, use

a lint-free, soft cloth slightly moistened with a diluted neutral detergent.

3. Do not disassemble any part of the microscope except for the parts that are specified to be disassembled in this manual,

as this could result in malfunction or reduced performance.

4. After using the microscope, set the main switch to “ ” (OFF), wait for the lamp housing to cool down sufficiently, and

keep it covered with a dust cover during storage.

5. Before disposing of this product, be sure to follow the regulations and rules of your local government.

CAUTION

BX63

This product complies with the requirements of directive 98/79/EC concerning in vitro diagnostic

medical devices. CE marking means the conformity to the directive.

4 Caution

If the microscope is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition,

the equipment may also be damaged. Always use the equipment as outlined in this instruction manual.

The following symbols are used to set off text in this instruction manual.

: Indicates a potentially hazardous situation which, if not avoided, may result in minor

or moderate injury or damage to the equipment or other property. It may also be used

to alert against unsafe practices.

} : Indicates commentary (for ease of operation and maintenance).

CAUTION

3 Intended use

This product has been designed to be used to observe magnified images of specimens in various routine work and

research applications.

Do not use this product for any purpose other than its intended use.

This product is considered a medical device in the following country: US.

Safety and EMC Precautions

· This product complies with the emission and immunity requirements described in IEC61326 series.

· The electromagnetic environment should be evaluated prior to operation of this product. Do not use this product in

close proximity to the sources of strong electromagnetic radiation to prevent interference with the proper operation.

· Use only power cord which OLYMPUS specifies. Otherwise the safety and EMC perfomance of the product can not

be assured.

· Be sure to ground the product. Otherwise our intended electric safety and EMC perfomance of the product can not

be assured.

Use in domestic area

EN61326-1 defines two categories according to the location for use.

Class A: Equipment suitable for use in establishments other than domestic, and those directly connected to a low voltage

power supply network which supplies buildings used for domestic purposes.

Class B: Equipment for use in domestic establishments, and in establishments directly connected to a low voltage power

supply network which supplies buildings used for domestic purposes.

This product is applied Class A. Some interference may occur if this system is used in domestic location.

1MODULE NOMENCLATURE

}The modules mentioned below show only the typical product names. As there are some products that are not mentioned

but also applicable to this microscope, check the latest catalogues or consult Olympus.

The control of motorized modules is possible from the touch panel controller, the U-MCZ controller or a PC (commercially

available).

For the modules marked “*”, also read their instruction manuals.

Observation tube

· U-BI30-2

· U-TBI3-CLI

· U-TR30-2

· U-TTR-2

Eyepieces

· WHN10X

· WHN10X-H

Motorized 7 position

nosepiece/Coded 7

position nosepiece

· U-D7REA

· U-D7RES

Stage

· BX3-SSU*

BX3-STAD + Stage for BX

· IX-SVL2

Motorized fluorescence illuminator/Coded

fluorescence illuminator/Standard arm

· BX3-RFAA*

· BX3-RFAS*

· BX3-ARM

Microscope frame

BX63F

Controller

U-MCZ*

XY controller*

Lamp housing

· U-LHLEDC

· U-LH100ADP + U-LH100

Control box

(for BX3-SSU)

Touch panel controller

(Provided with the BX63F)

Condenser

· BX3-UCD8A*

· U-SC3

· U-AAC

Control box

BX3-CBH*

Inhaltsverzeichnis

Andere Olympus Mikroskop Handbücher

Olympus

Olympus IMT-2 Bedienungsanleitung

Olympus

Olympus KHC Bedienungsanleitung

Olympus

Olympus CX31 Bedienungsanleitung

Olympus

Olympus DP21 Bedienungsanleitung

Olympus

Olympus BX3M-CB Bedienungsanleitung

Olympus

Olympus BH2 Series Betriebsanleitung

Olympus

Olympus U-D7RES Bedienungsanleitung

Olympus

Olympus U-UVF248 Bedienungsanleitung

Olympus

Olympus DP26 Bedienungsanleitung

Olympus

Olympus X-Tr Betriebsanleitung

Olympus

Olympus U-AW Bedienungsanleitung

Olympus

Olympus BX61 Bedienungsanleitung

Olympus

Olympus SZX16 Bedienungsanleitung

Olympus

Olympus BX43 Bedienungsanleitung

Olympus

Olympus BH2 Series Montageanleitung

Olympus

Olympus U-MDOB3 Bedienungsanleitung

Olympus

Olympus BX51WI Bedienungsanleitung

Olympus

Olympus VS120 Betriebsanleitung

Olympus

Olympus U-D7RES Bedienungsanleitung

Olympus

Olympus BHSU Montageanleitung

Olympus

Olympus BX51 Bedienungsanleitung

Olympus

Olympus CH30 Bedienungsanleitung

Olympus

Olympus VS110 Fluorescence Bedienungsanleitung

Olympus

Olympus Fluoview FV1000 Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Leica

Leica FL560 Bedienungsanleitung