Omron DRT1-ID Bedienungsanleitung

Transistor Remote Terminal DRT1-ID/OD

Compact 8-point and 16-point

Transistorized Terminals

Compact

(8-point models: 125 x 40 x 50 mm (W x H x D);

16-point models: 150 x 40 x 50 mm (W x H x D))

Two independent power supplies can be used

because the I/O terminals are insulated from the

internal circuits.

DIN track mounting and screw mounting are

available.

Ordering Information

I/O classification Internal I/O

circuit common I/O points Terminal Rated voltage I/O rated voltage Model

Input NPN (+ common) 8 Screw terminal 24 VDC 24 VDC DRT1-ID08

Output NPN (– common) DRT1-OD08

Input NPN (+ common) 16 DRT1-ID16

Output NPN (– common) DRT1-OD16

Specifications

Ratings

Input

Item DRT1-ID

Input current 10 mA max./point

ON delay time 1.5 ms max.

OFF delay time 1.5 ms max.

ON voltage 15 VDC min. between each input terminal and V

OFF voltage 5 VDC max. between each input terminal and V

OFF current 1 mA max.

Insulation method Photocoupler

Input indicators LED (yellow)

Output

Item DRT1-OD

Rated output current 0.3 A/point (see note)

Residual voltage 1.2 V max.

Leakage current 0.1 mA max.

Insulation method Photocoupler

Output indicators LED (yellow)

Note: Do not connect the DRT1-OD16 to loads consuming a total current exceeding 2.4 A.

DRT1-ID/OD DRT1-ID/OD

Characteristics

Communications power supply

voltage 11 to 25 VDC (supplied from the communications connector)

Internal power supply voltage 24 VDC +10%/–15%

I/O power supply voltage 24 VDC +10%/–15%

Current consumption (see note) Communications: 60 mA max. at 24 VDC

Internal circuit: 60 mA max. at 24 VDC

Dielectric strength 500 VAC for 1 min (1-mA sensing current between insulated circuits)

Noise immunity Power supply normal: ±600 V for 10 minutes with a pulse width of 100 ns to 1 µs

Power supply common: ±1,500 V for 10 minutes with a pulse width of 100 ns to 1 µs

Vibration resistance 10 to 55 Hz, 1.5-mm double amplitude

Shock resistance Malfunction: 200 m/s2(approx. 20G)

Destruction: 300 m/s2(approx. 30G)

Mounting strength No damage when 50 N (approx. 5 kgf) pull load was applied for 10 s in all directions (10 N min.

(approx. 1 kgf) in the DIN Track direction)

Terminal strength No damage when 50 N (approx. 5 kgf) pull load was applied for 10 s

Screw tightening torque 0.6 to 1.18 N Sm (6.2 to 12 kgf Scm)

Ambient temperature Operating: 0°C to 55°C (with no icing or condensation)

Storage: –20°C to 65°C (with no icing or condensation)

Ambient humidity Operating: 35% to 85%

Weight 8-point model: Approx. 135 g max.

16-point model: Approx. 170 g max.

Note: The above current consumption is a value with all 8 and 16 points turned ON excluding the current consumption of the external sensor

connected to the input Remote Terminal and the current consumption of the load connected to the output Remote Terminal.

Nomenclature

Communications

connector

DRT1-jD08

DRT1-jD16 MS

Indicators

0 to 15

DRT1-ID/OD DRT1-ID/OD

Indicators

Indicator Display Color Meaning

MS Lit Green The Unit is normal.

Flashes No node number has been set.

Lit Red The Unit has a fatal error.

Flashes The Unit has a nonfatal error.

Not lit No power is supplied to the Unit.

NS Lit Green The communications path is complete.

Flashes The communications path is incomplete.

Lit Red A fatal communications error has occurred.

Flashes Red A nonfatal communications error has occurred.

Not lit The communications power supply is OFF.

0 to 15

(t)

Lit Yellow The corresponding I/O signal is ON.

(see note) Not lit The corresponding I/O signal is OFF.

Note: The DRT1-D08 does not have indicators 8 to 15.

I/O Terminals

DIP Switch

Used for node number setting, baud rate set-

tings, and holding or clearing outputs for com-

munications error. Note: 1. Always turn OFF the Unit and the commu-

nications power supply before changing

DIP switch settings.

2. Pin 9 is not used. Always set pin 9 to OFF.

I/O Device Power Supply Terminals

Connected internally to the I/O power supply terminals.

Internal Circuit Power Supply Terminals

Connect a 24-VDC power supply.

I/O Power Supply Terminals

Connect a 24-VDC power supply.

Supply a maximum of 2 A at 24 VDC.

Baud Rate Setting

Node Number Settings

Output

HOLD/

CLEAR Mode

Baud Rate Settings

Pin 8 Pin 7

125,000 bps OFF OFF

250,000 bps OFF ON

500,000 bps ON OFF

Note: 1. Setting both pins 7 and 8 to OFF is not allowed.

2. Pins 7 and 8 are factory-set to OFF.

Output HOLD/CLEAR Mode

Mode Pin 10

HOLD ON

CLEAR OFF

Note: 1. Pin 9 is NC.

2. Pin 10 of the DRT1-ID08 or DRT1-ID16 is not used.

3. Pin 10 is factory-set to OFF.

DRT1-ID/OD DRT1-ID/OD

Node Number Settings

Node

Pin 6 Pin 5 Pin 4 Pin 3 Pin 2 Pin 1 Node

Pin 6 Pin 5 Pin 4 Pin 3 Pin 2 Pin 1

number 32 16 8 4 2 1 number 32 16 8 4 2 1

0 OFF OFF OFF OFF OFF OFF 32 ON OFF OFF OFF OFF OFF

1 OFF OFF OFF OFF OFF ON 33 ON OFF OFF OFF OFF ON

2 OFF OFF OFF OFF ON OFF 34 ON OFF OFF OFF ON OFF

3 OFF OFF OFF OFF ON ON 35 ON OFF OFF OFF ON ON

4 OFF OFF OFF ON OFF OFF 36 ON OFF OFF ON OFF OFF

5 OFF OFF OFF ON OFF ON 37 ON OFF OFF ON OFF ON

6 OFF OFF OFF ON ON OFF 38 ON OFF OFF ON ON OFF

7 OFF OFF OFF ON ON ON 39 ON OFF OFF ON ON ON

8 OFF OFF ON OFF OFF OFF 40 ON OFF ON OFF OFF OFF

9 OFF OFF ON OFF OFF ON 41 ON OFF ON OFF OFF ON

10 OFF OFF ON OFF ON OFF 42 ON OFF ON OFF ON OFF

11 OFF OFF ON OFF ON ON 43 ON OFF ON OFF ON ON

12 OFF OFF ON ON OFF OFF 44 ON OFF ON ON OFF OFF

13 OFF OFF ON ON OFF ON 45 ON OFF ON ON OFF ON

14 OFF OFF ON ON ON OFF 46 ON OFF ON ON ON OFF

15 OFF OFF ON ON ON ON 47 ON OFF ON ON ON ON

16 OFF ON OFF OFF OFF OFF 48 ON ON OFF OFF OFF OFF

17 OFF ON OFF OFF OFF ON 49 ON ON OFF OFF OFF ON

18 OFF ON OFF OFF ON OFF 50 ON ON OFF OFF ON OFF

19 OFF ON OFF OFF ON ON 51 ON ON OFF OFF ON ON

20 OFF ON OFF ON OFF OFF 52 ON ON OFF ON OFF OFF

21 OFF ON OFF ON OFF ON 53 ON ON OFF ON OFF ON

22 OFF ON OFF ON ON OFF 54 ON ON OFF ON ON OFF

23 OFF ON OFF ON ON ON 55 ON ON OFF ON ON ON

24 OFF ON ON OFF OFF OFF 56 ON ON ON OFF OFF OFF

25 OFF ON ON OFF OFF ON 57 ON ON ON OFF OFF ON

26 OFF ON ON OFF ON OFF 58 ON ON ON OFF ON OFF

27 OFF ON ON OFF ON ON 59 ON ON ON OFF ON ON

28 OFF ON ON ON OFF OFF 60 ON ON ON ON OFF OFF

29 OFF ON ON ON OFF ON 61 ON ON ON ON OFF ON

30 OFF ON ON ON ON OFF 62 ON ON ON ON ON OFF

31 OFF ON ON ON ON ON 63 ON ON ON ON ON ON

Note: The node number is factory-set to 0.

DRT1-ID/OD DRT1-ID/OD

Dimensions

Note: All units are in millimeters unless otherwise indicated.

DRT1-ID08

DRT1-OD08 Mounting Holes

Two, 4.2 dia. or M4

50 max.

40 max.

125 max.

Two, 4.2 dia. or M4

50 max.

40 max.

150 max.

Mounting Holes

DRT1-ID16

DRT1-OD16

Fourteen, M3

Twenty-two, M3

DRT1-ID/OD DRT1-ID/OD

Installation

Internal Circuit Configuration

DRT1-ID08

DRT1-ID16

DRT1-OD08

DRT1-OD16

Input

terminals

DC–DC

converter

(insulated)

24 VDC

DC–DC

converter

(insulated)

24 VDC

Output

terminals

Communications

connector

Power supply for

internal circuitry

Communications

connector

Power supply for

internal circuitry

Physi-

cal lay-

Physi-

cal lay-

Internal circuit

Photo-

coupler

Photo-

coupler Photo-

coupler

Photo-

coupler

Photo-

coupler

Photo-

coupler

Photo-

coupler

Photo-

coupler

Voltage step-down

Wiring

Input

DRT1-ID08

DRT1-ID16

Three-wired Sensors (NPN Output) Two-wired Sensors

Brown

Black

Blue

Brown

Sensor 1

Brown

Black

Blue

Sensor 2

Blue

Sensor 1

Brown

Blue

Sensor 2 L1 L1

Output

DRT1-OD08

DRT1-OD16

DRT1-ID/OD DRT1-ID/OD

Terminal Arrangement and I/O Device Connection Example

Input

DRT1-ID08 DRT1-ID16

Output

DRT1-OD08 DRT1-OD16

Photoelectric sensor or

proximity sensor (three-

wired sensor with a built-in

amplifier)

Limit switch

(two-wired

sensor)

Internal

circuit

power

supply

Blue

Brown

Blue

Black

Brown

Internal

circuit

power

supply

I/O

power

supply

I/O power

supply

Solenoid, etc. Valve, etc.

Brown

Black

Blue

Internal

circuit

power

supply

I/O power

supply

Internal

circuit

power

supply

Shield

Blue (communications data L)

Black (communications power supply –)

White (communications data H)

Red (communications power supply +)

I/O

power

supply

Solenoid, etc. Valve, etc.

Photoelectric sensor or

proximity sensor (three-

wired sensor with a built-in

amplifier)

Limit switch

(two-wired

sensor)

Shield

Blue (communications data L)

Black (communications power supply –)

White (communications data H)

Red (communications power supply +)

Shield

Blue (communications data L)

Black (communications power supply –)

White (communications data H)

Red (communications power supply +)

Shield

Blue (communications data L)

Black (communications power supply –)

White (communications data H)

Red (communications power supply +)

DRT1-ID/OD DRT1-ID/OD

Specifications subject to change without notice. Printed in U.S.A.

Precautions

Refertothe

CompoBus/DOperationManual(W267)

before usingthe

Unit.

These precautions are also for the DRT1-ID16X/OD16X.

General Safety Precautions

Wiring

TurnOFF the Unitbeforewiring the Unitand do notremovethe termi-

nalblockcoverortouchtheterminalblock whiletheUnitis turnedON,

otherwisean electric shock may occur.

Do not impose any voltage other than the rated voltage on the input

terminal.DoingsomayresultindamagetotheUnitorcausetheUnitto

malfunction.

Do not connect the Unit to loads consuming a total current exceeding

the rated output current of the Unit. Doing so may damage the output

elementand a short- or open-circuit malfunction may result.

If the Unit is connected to a DC inductive load, connect a diode to the

Unit to protect the Unit from counter-electromotive voltage, otherwise

the counter-electromotive voltage may damage the output element

and a short- or open-circuit malfunction may result.

Correct Use

Cable Locks

BeforeturningontheUnit,makesurethattheconnectorofeachcable

connectedto the Unit is locked.

Do not connect or disconnect the connectors while the Unit is turned

ON. Doing so may cause the Unit to malfunction.

Installation Environment

Do not install the Unit in the following places. Doing so may result in

damage to the Unit or cause the Unit to malfunction.

•Places with direct sunlight.

•Places with ambient temperature ranges not within 0°C to 55°C.

•Places with rapid temperature changes resulting in condensation

or relative humidity ranges not within 10% to 90%.

•Places with corrosive or inflammable gas.

•Places with excessive dust, salinity, or metal powder.

•Places with vibration or shock affecting the Unit.

•Places with water, oil, or chemical sprayed on the Unit.

Screw Tightening Torques

Tightenall screws of the Unit properly, otherwise the Unit may mal-

function.

•Tighteneach terminal screw to a torque of 0.6 to 1.18 N m (6.2 to

12.0kgf cm).

•Tighteneachmountingscrewtoatorqueof0.6to0.98Nm(6.2to

10.0kgf cm) if the Unit is mounted to a panel.

Cleaning

Use alcohol or benzine to clean the surface of the Unit. Do not use

paintthinner to clean the surface, otherwise the surface will be dam-

agedor discolored.

Handling

Donot dropthe Unitor shockor vibratethe Unitexcessively. Doingso

may result in damage to the Unit or cause the Unit to malfunction.

Disassembling, Repairing, and Modifying

Do not disassemble, repair, or modify the Unit, otherwise an electric

shock may occur or the Unit may malfunction.

Omron Europe B.V. EMA-ISD, tel:+31 23 5681390, fax:+31 23 5681397, http://www.eu.omron.com/ema

NOTE: ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. TO CONVERT MILLIMETERS TO INCHES DIVIDE BY 25.4.



Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Omron Touch-Terminal Handbücher

Omron

Omron NT612G Series Bedienungsanleitung

Omron

Omron Programmable Terminals NT631 Installationshandbuch

Omron

Omron ns series Benutzerhandbuch

Omron

Omron NS - Benutzerhandbuch

Omron

Omron NS - Betriebsanleitung

Omron

Omron NT2S-SF123B-E - Gebrauchsanweisung

Omron

Omron NT31C Series Bedienungsanleitung

Omron

Omron NXR-ILM08C-ECT Bedienungsanleitung

Omron

Omron Programmable Terminals NT31 NT31C Benutzerhandbuch

Omron

Omron NA-series Gebrauchsanweisung

Omron

Omron NP Series Bedienungsanleitung

Omron

Omron NT11S Bedienungsanleitung

Omron

Omron NV Series Betriebsanleitung

Omron

Omron NT30 Bedienungsanleitung

Omron

Omron NA-series Benutzerhandbuch

Omron

Omron NA5-12W series Gebrauchsanweisung

Omron

Omron NT31 Series Benutzerhandbuch

Omron

Omron NT11 - 01-2004 Bedienungsanleitung

Omron

Omron NV3Q Series Gebrauchsanweisung

Omron

Omron DEVICENET#05-2003 Bedienungsanleitung

Omron

Omron NV Series Benutzerhandbuch

Omron

Omron NS - Gebrauchsanweisung

Omron

Omron NA-series Gebrauchsanweisung

Omron

Omron NT31 Series Installationshandbuch

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung