Omron NT2S-SF121B-E - Bedienungsanleitung

Version 1.03 Page 1

NT2S-SF121B-E

NT2S-SF122B-E

QUICK START GUIDE - V1.03

Version 1.03 Page 2

NT2ST QUICK START GUIDE

1. INTRODUCTION ............................................................................................................................................ 3

2. NT2S OPERATION OVERVIEW ................................................................................................................... 3

3. NT2ST SOFTWARE OVERVIEW..................................................................................................................4

4. ADD/REMOVE DRIVERS.............................................................................................................................. 5

5. CREATE NEW PROJECT...............................................................................................................................6

6. PROJECT SETUP............................................................................................................................................. 7

7. TAG DATABASE............................................................................................................................................8

8. EDIT – SCREENS..........................................................................................................................................10

9. NORMAL SCREEN....................................................................................................................................... 11

10. LINK SCREEN............................................................................................................................................... 15

11. SPECIAL SCREEN........................................................................................................................................16

12. FUNCTION SCREEN.................................................................................................................................... 18

13. SPECIAL PROGRAMMING NOTES ...........................................................................................................20

STR Control from a Function Key ...................................................................................................................... 20

STR Control from the PLC.................................................................................................................................. 20

Function Key Control Definitions....................................................................................................................... 20

Entering Text on Second Line of Display............................................................................................................ 21

14. COMMUNICATION CABLES SPECIFICATIONS..................................................................................... 22

Omron Cables....................................................................................................................................................22

Allen-Bradley Cables.......................................................................................................................................... 24

GE Micro Cables ................................................................................................................................................25

Modicon Cables.................................................................................................................................................. 26

Keyence Cables...................................................................................................................................................27

Toshiba Cables....................................................................................................................................................28

Koyo Cables........................................................................................................................................................ 29

15. NT2S SPECIFICATIONS ..............................................................................................................................30

Version 1.03 Page 3

1. INTRODUCTION

NT2ST is used with NT2S-SF121B-E and NT2S-SF122B-E products. These products are

compact but highly functional operator interfaces and NT2ST is designed to be extremely

flexible to take advantage of this functionality.

The bright LED back light and 2 x 16 character screen provide a highly visible display for

showing fixed or scrolling text messages, bit controlled text, and numerical data.

Special screen types exist for simplifying data entry. Navigation can be achieved using

programmed function keys, configuring a LINK screen, or chaining message screens that change

on a timer. Six function keys provide many options for operator control and data entry.

Function keys can be programmed locally for each screen, or globally for the project, to perform

tasks which include momentary, set on, set off, and toggle bit control, as well as numerous

numeric value control tasks.

The Windows based program, NT2ST, provides many tools to achieve flexible solutions. Follow

this quick start guide to gain an overall understanding of the layout of this software tool.

This document assumes the user is familiar with the operation of programs within Windows and

basic PLC concepts. Consult a technical resource for answers to basic PLC questions.

2. NT2S OPERATION OVERVIEW

The screens displayed on the NT2S are stored in the program memory of the unit. The NT2S

displays the screen number currently stored in the Screen Trigger Register (STR), which is a

PLC memory location. The NT2S remembers the last three STR values and will display them in

order when the current screen is finished displaying.

Numeric data is displayed by placing fields on a screen that reference PLC memory locations.

Up to six numeric fields can be placed on a single screen. Bit status can be displayed on the

screen using bit controlled text.

Navigation from screen to screen can be handled in several ways:

•Function keys can be programmed to change the STR. F1 can increment the STR by one,

and F2 can decrement the STR by 1. Function keys can also change the STR to a specified

number.

•Link screens can be created to navigate a series of screens specified by the user. A link

screen is a parent screen which displays a series of child screens. Link screens save

programming time because it automatically defaults to F1 being a NEXT key, and F2 being a

PREV key. Programmer does not have to set these functions up on each screen. Call the link

screen number in the STR to activate the link screen.

•Chained screens can be used to automatically cycle through a list of screens. When creating a

screen, specify to what screen number it is linked. During operation, the NT2S will continue

to change screens at the rate specified in the MIN TIME field of each screen. The screens

will loop until a STR number is called for a screen not in the chain.

Version 1.03 Page 4

3. NT2ST SOFTWARE OVERVIEW

It is recommended that programming steps be performed by accessing the Windows menu items

at the top of the program window. Deactivate the Tool Station (the Desktop cartoon image) by

selecting Options menu, Tool Station. The tool station should disappear.

Select Help at any point within NT2ST to view context sensitive help information. The help

document will provide a more thorough explanation than this document will for most functions.

The sections below are roughly in the order in which a project will be created.

Version 1.03 Page 5

4. ADD/REMOVE DRIVERS

Before beginning the first project, select Project and Add/Remove Drivers. This menu item is

not available once a project has been created.

A dialog will appear that allows additional PLC models to be added to the PLC selection menu.

Make sure that the PLC needed for the project is included in the list on the right.

Select OK to complete addition of drivers to the project.

Version 1.03 Page 6

5. CREATE NEW PROJECT

1. Select New from the Project menu.

2. In the dialog presented, select the PLC and PLC Model from the New project dialog and

select OK.

The PLC model can be changed at any time during the project. From the Project menu,

select, PLC Model, and select a new PLC model from the list. Accept the change by

clicking on OK. Care must be taken to verify that the tag addresses are valid for the new

PLC model.

(If the brand of PLC required for the project does not appear, refer to the ADD/REMOVE DRIVERS section

above.)

3. Select the NT2S hardware model that will be used for this project. Choose either NT2S-

SF121B-E or NT2S-SF122B-E and click the CLOSE button.

(If the incorrect NT2S model is selected, the project can be converted at anytime using the file conversion

utility located on the Project menu, and select Model type. Just open the project and select this menu item and

select OK.)

Version 1.03 Page 7

6. PROJECT SETUP

The Setup dialog is used to configure the NT2S operation parameters. Specify the LED register,

screen trigger register, power up screen, serial port settings, function key password, and real time

clock download time. The project setup dialog is accessed from the Edit menu, Setup menu

item.

Generally, there is no need to change the default settings. The only parameters that need to be

set by the user are Power up screen number and the function key password settings.

LED Register – This setting tells the NT2S which TAG to reference for the LED Register. Any TAG of the proper

type can be referenced for this setting. The default TAG is labeled “LED Register”.

STR – This setting tells the NT2S which TAG to reference for the Screen Trigger Register. Any TAG of the proper

type can be referenced for this setting. The default TAG is labeled “Screen Trigger Reg”.

Power Up Screen – Enter the screen number for the screen that should appear at system start-up. This screen

number is only referenced internally from the NT2S and is not written down to the STR in the PLC.

Serial Port settings: Set the serial port parameters for serial printer connection. The communication is Serial

RS232, Selectable 7 or 8 bit, Odd, Even or No Parity, No handshake, 300, 600, 1200, 2400, 4800, 9600 or 19200

Baud.

NOTE: Serial Communications specifications apply to the Unit - printer setup and do not affect PC to Unit

communications.

Function Key Password – This password will be applied to any function key that has the password activated. The

password will be used throughout the project.

RTC Download Time (NT2S-SF121B-E only) – Enter the time interval for downloading the RTC tags to the PLC

here. The values range from 0 to 600 ( seconds ). 0 means the values will be downloaded as fast as possible. Any

other interval will mean that NT2S will wait for the specific time interval before downloading the value into the

PLC.

Version 1.03 Page 8

7. TAG DATABASE

Once the project has been created, the very first step should be to define the TAG DATABASE.

The tag database is a list of names (tags) that reference PLC registers or coils (bits). When

programming screens, reference is made to this tag database. Users can choose to reference the

tags either by name or PLC address.

Tags will be referenced while creating the NT2S screens are created. Tags can always be edited

or modified later in the project.

New projects are created a set of default TAGS. For instance, NT2S-SF122B-E has the

following tags:

0001 LED Register |DM00001|

0002 Screen Trigger Reg |DM00000|

NT2S-SF121B-E projects are created with 8 tags. Tags 0003 through 0008 are associated with

the RTC and cannot be directly addressed in NT2ST. Their addresses are offset from the LED

0001 LED Register |DM00001|

0002 Screen Trigger Reg |DM00000|

0003 Date LED Register + 2 (Lower byte) ---- Date (DD)

0004 Month LED Register + 3 (Higher byte) ---- Month (MO)

0005 Year LED Register + 3 (Lower byte) ---- Year (YY)

0006 Hours LED Register + 1 (Higher byte) ---- Hours (HH)

0007 Minutes LED Register + 1 (Lower byte) ---- Minutes (MI)

0008 Seconds LED Register + 2 (Higher byte) ---- Minutes (MI)

Version 1.03 Page 9

CREATE A REGISTER

A tag can reference an entire word in PLC memory, called a register. Use the following steps to

create a tag for a register:

1. Select Tag Database from the Edit menu.

2. From the Tag Database editor dialog (shown above), choose NEW.

3. Select the Register button.

4. Choose the PLC memory location from the provided list box.

5. Select the specific register number in the address box provided.

6. Enter a tag name in the lower text box.

7. Select ADD button to complete the creation of the register tag.

CREATE A COIL

A tag can reference a bit in PLC memory, called a coil. Use the following steps to create a tag

for a coil:

1. Select Tag Database from the Edit menu.

2. From the Tag Database editor dialog, choose NEW.

3. Select the Coil button.

4. Choose the PLC memory location from the provided list box.

5. Select the specific register and bit number in the address box provided.

6. Enter a tag name in the lower text box.

7. Select ADD button to complete the creation of the coil tag.

Version 1.03 Page 10

8. EDIT – SCREENS

Launch Screen Editor from EDIT menu. Select SCREENS menu item.

1. From the Edit menu, select the Screens item.

2. Click on the new screen button !to launch the screen type selection dialog, New

Screen.

3. Four different types of screens can be selected from the New Screen dialog: Normal, Link,

Special, and Function. The following sections will discuss each type of screen. Choose a

screen type, enter a screen number, and select OK to launch the Editing Screen dialog.

Andere Handbücher für NT2S-SF121B-E -

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Omron Touch-Terminal Handbücher

Omron

Omron NS10-TV Series Bedienungsanleitung

Omron

Omron NA-series Gebrauchsanweisung

Omron

Omron NP3 Series Referenzhandbuch

Omron

Omron Programmable Terminals NT631 Benutzerhandbuch

Omron

Omron NT21 Bedienungsanleitung

Omron

Omron PRT1-COM Bedienungsanleitung

Omron

Omron NS10-TV Series Betriebsanleitung

Omron

Omron NV Series Betriebsanleitung

Omron

Omron NP Series Bedienungsanleitung

Omron

Omron NT11 - 01-2004 Bedienungsanleitung

Omron

Omron NA-series Bedienungsanleitung

Omron

Omron NT11S Bedienungsanleitung

Omron

Omron NT612G Series Bedienungsanleitung

Omron

Omron NXR-ILM08C-ECT Bedienungsanleitung

Omron

Omron NT2S-SF122B-E START V1.03 Gebrauchsanweisung

Omron

Omron NTXS Bedienungsanleitung

Omron

Omron NT11 - 01-2004 Bedienungsanleitung

Omron

Omron NS12-TS00 Series Benutzerhandbuch

Omron

Omron Programmable Terminals NT631 Installationshandbuch

Omron

Omron WT30 Bedienungsanleitung

Omron

Omron PC CONNECTION - 04-1997 Bedienungsanleitung

Omron

Omron NS - Gebrauchsanweisung

Omron

Omron NB3Q-TW**B series Installations- und Betriebshandbuch

Omron

Omron NT20S-ST121B-EV3 Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung