Panasonic EX-10 Series Bedienungsanleitung

2013.10 http://panasonic.net/id/pidsx/global

Amplier Built-in Ultra-slim

Photoelectric sensor

EX-10 Series

USER’S MANUAL

WUME-EX10-4

[email protected] www.digiparts.ch

Ihr Schweizer Industriepartner

Contents

1. Safety precaution ······································································· 3

2. Part Description ········································································· 4

3. Mounting ····················································································· 6

3-1 Mounting of the sensor··························································6

3-2 Mounting interval···································································7

4. I/O Circuit Diagram ··································································13

5. Stability Indicator ····································································· 14

6. Beam alignment ······································································· 14

7. Option ·······················································································15

7-1

Slit Mask

(optional)······························································15

7-2 Sensor mounting bracket

(optional)·····································15

8. Specications ··········································································· 16

8-1 Standard-beam type····························································16

8-2 Narrow-beam type·······························································18

9. Dimentions ···············································································19

[email protected] www.digiparts.ch

Ihr Schweizer Industriepartner

1. Safety precaution

WARNING

●Never use this product as a sensing device for personnel protection.

●In case of using devices for personnel protection, use products which meet laws and

standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in

each region or country.

●This product has been developed / produced for industrial use only.

●The narrow beam type EX-1□S□ emits a narrow light beam, so it is difcult to align the beam. Use

the instrument with the emitter and the receiver facing each other in a straight line. Note that if

screws or other parts become loose due to vibration, for example, the beam axis may drift.

●Sensor mounting baracket (optional) MS-EX-10-□is an object for satandard-beam type.

It cannot be used for narrow-beam type.

● For the convergent reective type EX-14□, if there is a reective object (e.g., a conveyor, etc.) in

the background of the sensing object, since it may affect the sensing, use by keeping enough dis-

tance from the reective object.

●The thin cable 0.1mm2is used for this product. Thus, take care that if the cable is pulled with ex-

cessive force, it may cause cable break.

●Extension up to total 50m (each emitter and receiver of thru-beam type), or less, is possible with

0.3mm2, or more of conductor area cable. However,the extension of a power supply line and the

output line of less than 10m is acceptable in case using this product as conforming to S-mark.

●Make sure that stress by forcible bend or pulling is not applied directly to the sensor cable joint.

●Make sure to carry out wiring in the power supply off condition.

●Take care that wrong wiring will damage the sensor.

●Verify that the supply voltage variation is within the rating.

●If power is supplied from a commercial switching regulator, ensure that the frame ground (F.G.)

terminal of the power supply is connected to an actual ground.

●In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity

of this product, connect the frame ground (F.G.) terminal of the equipment to an actual ground.

●Do not run the wires together with high-voltage lines or power lines, or put them in the same race-

way.

● Take care that the sensor is not directly exposed to uorescent lamp from a rapid-starter lamp, a

high frequency lighting device or sunlight etc., as it may affect the sensing performance.

●Do not use during the initial transient time (EX-15□, EX-15E□, EX-17□, EX-17E□: 100ms / others:

50ms) after the power supply is switched ON.

●This sensor is suitable for indoor use only.

●Do not use this sensor in places having excessive vapor, dust, etc., or where it may come in con-

tact with corrosive gas, etc.

●Take care that the product does not come in contact with oil, grease, organic solvents such as

thinner, etc., strong acid or alkaline.

● This product cannot be used in an environment containing inammable or explosive gasses.

●Never disassemble or modify the product.

●Since the cable end is not waterproof, do not use the sensor in the application where water may

seep in from the cable end.

[email protected] www.digiparts.ch

Ihr Schweizer Industriepartner

2. Part Description

Thru-beam front sensing type: EX-11□ , EX-13□ , EX-19□,

EX-11S□ , EX-13S□ , EX-19S□

Thru-beam side sensing type: EX-11E□ , EX-13E□ , EX-19E□

EX-11SE□ , EX-13SE□ ,

Convergent reective front sensing type: EX-14□

Mounting

hole

Beam

emitting

part

Beam

receiving

part

Operation indicator

(Orange)

Stability indicator

(Green)

Mounting hole

Mounting hole

Beam

emitting

part

Operation indicator

(Orange)

Stability indicator

(Green)

Beam

receiving part

Mounting

hole

Beam receiving part

Beam emitting part

Mounting hole

Operation indicator

(Orange)

Stability indicator

(Green)

[email protected] www.digiparts.ch

Ihr Schweizer Industriepartner

Switch position Operation Description

Light-ON Light-ON mode is set when the switch is turned fully clockwise (L side).

Dark-ON Dark-ON mode is set when the switch is turned fully counterclockwise

(D side).

Thru-beam front sensing type with

operation mode switch on bifurcation:

EX-15, EX-17

Thru-beam side sensing type with

operation mode switch on bifurcation:

EX-15E, EX-17E

Operation mode switch

L: Light-ON

D: Dark-ON

Operation indicator (Orange)

Light up when the output is ON.

Operation mode switch

Operation indicator

(Orange)

Mounting

hole

Beam

receiving

part

Beam

emitting

part

Mounting

hole

Stability indicator (Green)

Operation indicator(Orange)

Mounting

hole

Mounting

hole

Beam

emitting

part

Beam

receiving

part Stability indicator

(Green)

Operation mode switch

Operation indicator

(Orange)

Operation indicator

(Orange)

[email protected] www.digiparts.ch

Ihr Schweizer Industriepartner

3. Mounting

3-1 Mounting of the sensor

●The tightening torque should be 0.2 N·m or less.

●The narrow beam type EX-1□S□ emits a narrow light beam, so it is difcult to align the beam.

Note that if screws or other parts become loose due to vibration, for example, the beam axis may

drift.

●In case of mounting on tapped holes (Unit: mm)

●In case of using attached screws and nuts (Unit: mm)

●In case of using mounting bracket (optional)

The sensor bracket is an object for satandard-beam type. It cannot be used for narrow-

beam type.

MS-EX-10-2 MS-EX-10-3

MS-EX-10-1

MS-EX-10-11 MS-EX-10-12 MS-EX-10-13

Side sensingFront sensing

M2 × 0.4

tapped, 7 deep

Sensing

direction

M2 screw

[length 8

(accessory)

]

Sensing

direction

M2 × 0.4

tapped, 6 deep

Thickness of mounting

plate: 2.5 or less

Flat washers

(accessory)

Nuts

(accessory)

Spring washers

(accessory)

Front sensing

Sensing

direction

M2 screw

[length 8

(accessory)

]

Side sensing

Thickness of mounting

plate: 2 or less

Flat washers

(accessory)

Nuts

(accessory)

Spring washers

(accessory)

Sensing

direction

Material: SPCC (Uni-chrome plated)

Two M2 (length 4 mm) pan

head screws (Accessory)

Material: SPCC (Uni-chrome plated)

Two M2 (length 8 mm) pan

head screws (Accessory)

Material: SPCC (Uni-chrome plated)

Two M2 (length 4 mm) pan head screws

Two M2 (length 8 mm) pan head screws

Accessory: 2 pan head screws each

Material: SUS304

Two M2 (length 4 mm) pan

head screws (Accessory)

Material: SUS304

Two M2 (length 8 mm) pan

head screws (Accessory)

Material: SUS304

Two M2 (length 4 mm) pan head screws

SUS304

Two M2 (length 8 mm) pan head screws

SUS304

Accessory: 2 pan head screws each

M2 screw

[length 10

(accessory)

]

M2 screw

[length 10

(accessory)

]

[email protected] www.digiparts.ch

Ihr Schweizer Industriepartner

3-2 Mounting interval

●This product does not incorporate auto interference function. In case mounting two sets

or more of the this product close together, please mount them as drawing below indi-

cates (typical example)

● Find out the operating point ℓ on the parallel deviation diagram for the setting distance L.

Separate sensors by 2 × ℓ or more.

In case using at sensing distance (L1) 150mm, the op-

eration point (ℓ1) is approx. 23.4mm according to dia-

gram above.

The installation interval is

Approx. 23.4mm × 2 = approx. 46.8mm

Thus, install approx.46.8mm or more away.

In case using at sensing distance (L2) 150mm, the

operation point (ℓ2) is approx. 15mm according to dia-

gram above.

The installation interval is

Approx. 15mm × 2 = approx. 30mm

Thus, install approx. 30mm or more away.

Thru-beam type: EX-11E□, EX-15E□, parallel deviation diagram (typical)

(ℓ2)

200

150

100

(L2)

Thru-beam type: EX-11□, EX-15□, parallel deviation diagram (typical)

100

(ℓ1)

50 0 50 100

200

150

100

(L1)

100 50 0 50 100

Sensing distance L (mm)

CenterLeft Right

Operating point ℓ (mm)

100 50 0 50 100

Sensing distance L (mm)

CenterLeft Right

Operating point ℓ(mm)

EX-11E□,EX-15E□: Approx. 30mm or more

150mm

Emitter Receiver

EX-11□,EX-15□: Approx. 46.8mm or more

150mm

EX-11□,EX-15□: Approx. 46.8mm or more

Emitter Receiver

[email protected] www.digiparts.ch

Ihr Schweizer Industriepartner

In case using at sensing distance (L3) 500mm, the

operation point (ℓ3) is approx. 76.6mm according to

diagram above.

The installation interval is

Approx. 76.6mm × 2 = approx. 153.2mm

Thus, install approx. 153.2mm or more away

In case using at sensing distance (L4) 500mm, the

operation point (ℓ4) is approx. 50mm according to dia-

gram above.

The installation interval is

Approx. 50mm × 2 = approx. 100mm

Thus, install approx. 100mm or more away.

EX-13E□,EX-17E□: approx. 100mm or more

500mm

Emitter Receiver

Thru-beam type: EX-13□, EX-17□ parallel deviation diagram (typical)

100 50 0 50 100

(ℓ3)

(L3)

800

400

600

200

Thru-beam type: EX-13E□, EX-17E□ parallel deviation diagram (typical)

100 50 0 50 100

(ℓ4)

(L4)

800

400

600

200

Sensing distance L (mm)

CenterLeft Right

Operating point ℓ (mm)

Sensing distance L (mm)

CenterLeft Right

Operating point ℓ(mm)

EX-13□,EX-17□ approx. 153.2mm or more

500mm

EX-13□,EX-17□ approx. 153.2mm or more

Emitter Receiver

[email protected] www.digiparts.ch

Ihr Schweizer Industriepartner

Thru-beam type: EX-19□, parallel deviation diagram (typical)

(ℓ5)

(L5)

200 100 0 100 200

0.5

Sensing distance L (m)

CenterLeft Right

Operating point ℓ(mm)

In case using at sensing distance (L5) 1m,

the operation point (ℓ5) is approx. 128.6mm

according to diagram above.

The installation interval is

Approx. 128.6mm × 2 = approx. 257.2mm

Thus, install approx. 257.2 or more away.

Emitter Receiver

EX-19□: approx. 257.2mm or more

Thru-beam type: EX-19E□, parallel deviation diagram (typical)

(ℓ6)

(L6)

200 100 0 100 200

0.5

Sensing distance L (m)

CenterLeft Right

Operating point ℓ(mm)

In case using at sensing distance (L6) 1m,

the operation point (ℓ6) is approx. 71.1mm

according to diagram above.

The installation interval is

Approx. 71.1mm × 2 = approx. 142.2mm

Thus, install approx.142.2 or more away.

EX-19E□：approx.142.2mm or more

Emitter Receiver

[email protected] www.digiparts.ch

Ihr Schweizer Industriepartner

Thru-beam type: EX-11S□, parallel deviation diagram (typical)

CenterLeft Right

Operating point ℓ(mm)

Sensing distance L (mm)

50 25 0 25 50

200

150

100

(ℓ7)

(L7)

In case using at sensing distance (L7)

150mm, the operation point (ℓ7) is approx.

10.8mm according to diagram above.

The installation interval is

Approx. 10.8mm × 2 = approx. 21.6mm

Thus, install approx.21.6 or more away.

Emitter Receiver

EX-11S□: approx. 21.6mm or more

150mm

EX-11S□: approx. 21.6mm or more

Thru-beam type: EX-11SE□, parallel deviation diagram (typical)

50 25 0 25 50

200

150

100

(L8)

(ℓ8)

CenterLeft Right

Operating point ℓ(mm)

Sensing distance L (mm)

In case using at sensing distance (L8)

150mm, the operation point (ℓ8) is approx.

6.2mm according to diagram above.

The installation interval is

Approx. 6.2mm × 2 = approx. 12.4mm

Thus, install approx.12.4 or more away.

EX-11SE□: approx. 12.4mm or more

150mm

Emitter Receiver

EX-11SE□: approx. 12.4mm or more

[email protected] www.digiparts.ch

Ihr Schweizer Industriepartner

Andere Handbücher für EX-10 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Zubehör Handbücher

Panasonic

Panasonic MA24D52 Bedienungsanleitung

Panasonic

Panasonic AKHBU931P - CCU FOR AKHC931 Bedienungsanleitung

Panasonic

Panasonic PM2 Series Bedienungsanleitung

Panasonic

Panasonic MA4ZD03 Bedienungsanleitung

Panasonic

Panasonic LS-H Series Bedienungsanleitung

Panasonic

Panasonic HL-C211F5-MK Bedienungsanleitung

Panasonic

Panasonic MA3S781D Bedienungsanleitung

Panasonic

Panasonic MAZ9xxxH Series Bedienungsanleitung

Panasonic

Panasonic EX-L200 Series Bedienungsanleitung

Panasonic

Panasonic MCO-230AIC Bedienungsanleitung

Panasonic

Panasonic PAW-DEWPOINTSENSOR Bedienungsanleitung

Panasonic

Panasonic LNJ216C8ARA Bedienungsanleitung

Panasonic

Panasonic MQ-W3A-DC12-24VEM Bedienungsanleitung

Panasonic

Panasonic DP-00 Series Bedienungsanleitung

Panasonic

Panasonic MALT062H Bedienungsanleitung

Panasonic

Panasonic Digital Fiber Sensor FX-301 Bedienungsanleitung

Panasonic

Panasonic KX-HNS103 Bedienungsanleitung

Panasonic

Panasonic MA3SD29F Bedienungsanleitung

Panasonic

Panasonic Light Emitting Diodes LN360GPX Bedienungsanleitung

Panasonic

Panasonic DP-100 series Bedienungsanleitung

Panasonic

Panasonic MA3X748 (MA748) Bedienungsanleitung

Panasonic

Panasonic WV-TW370 Betriebsanleitung

Panasonic

Panasonic MA3Z7920G Bedienungsanleitung

Panasonic

Panasonic MA5J002E Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Bedienungsanleitung