Panasonic MC-CG467-ZU21 Bedienungsanleitung
© 2007 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and distribu-
tion is a violation of law.
Order No VCB0704007CE
Vacuum Cleaner
MC-CG467-ZU21
Product color Z)Sherbet blue
Destination : USA
TABLE OF CONTENTS
PAGE PAGE
1 Specifications ----------------------------------------------------- 2
2 Location of Controls and Components ------------------- 3
3 Troubleshooting Guide ----------------------------------------- 5
4 Disassembly and Assembly Instructions ---------------- 6
4.1. Dust box cover assembly removal -------------------- 6
4.2. Separate the upper and lower body units ----------- 6
4.3. Printed Circuit Board A Unit (P.C.B A Unit)
removal------------------------------------------------------- 7
4.4. Motor removal ---------------------------------------------- 8
4.5. Cord reel partition unit replacement ------------------ 9
4.6. Rail base U replacement -------------------------------- 9
4.7. Spring-loaded cord reel pre-winding------------------ 9
4.8. How to disassemble the turbine nozzle ------------10
5 Wiring Connection Diagram ---------------------------------11
6 Exploded View and Replacement Parts List -----------12
6.1. EXPLODED VIEW (ATTACHMENTS) --------------12
6.2. PARTS LIST (ATTACHMENTS) ----------------------13
6.3. EXPLODED VIEW (BODY UNIT)-------------------- 14
6.4. PARTS LIST (BODY UNIT)---------------------------- 15
6.5. PACKING INSTRUCTIONS --------------------------- 16
6.6. PACKING LIST ------------------------------------------- 17
2
1 Specifications
Model No. MC-CG467-ZU21
Power source AC120V ~ 60Hz
Current 11Amps
Automatic cord rewind YES
Dust bag Paper
Dust capacity 3.0 L
Extension wand Metal telescopic
Floor nozzle 3-in-1 Turbo brush
Dimensions (WxLxH)mm 280x425x260
Cord length 5.0m
Net weight 4.5kg
Cleaning tools Crevice nozzle / Dusting brush
3
2 Location of Controls and Components
4
5
3 Troubleshooting Guide
CONDITION CHECKPOINT METHOD OF INSPECTION CAUSE / REMEDY
Motor fails to rotate
(no noise is heard at all)
Power supply cord Check power supply cord continu-
ity.
If there is no continuity, replace the
cord reel patition unit.
Fuse
(125V, 15A)
Check fuse continuity. If there is no continuity, replace Rail
Base unit.
Motor continuity Check the conduction between the
terminals of the motor.
If there is no continuity, replace the
motor.
ON/OFF Switch Check continuity across switch
connections
At switch ON, if there is no continu-
ity, replace P.C.B A Unit.
P.C.B A Unit Check the internal parts for any-
thing unusual. (burn-out, melt-
down, etc.)
If anything is found unusual,
replace the P.C.B A Unit with new
one.
Motor runs but there is no suction Hose or Suction inlet Check if there is any blockage in
the hose or suction inlet.
If there is any blockage, remove it.
Dust bog / Secondary filter Check if dust bag is full or Second-
ary filter is choked up.
If dust bag is full, replace with a
new one. If Secondary filter is
choked up, remove and clean it out
or replace.
Noise or vibration Motor fan Check dust accumulated in motor
fan (it could happen if the vacuum
cleaner has been used without cen-
tral filter).
If there is dust accumulated in the
motor fan, replace the motor and
check filter condition. (never try to
dismantle the motor fan)
Motor does not change power
(runs always at full speed)
Power control Adjust the power control and check
whether or not the resistance var-
ies.
If the resistance does not vary, then
replace the P.C.B A Unit.
P.C.B A Unit Examine the triac in the P.C.B A
Unit and check whether or not T1
and T2 are short-circuited.
If they are short-circuited, then
replace the P.C.B A Unit.
6
4 Disassembly and Assembly Instructions
Important notice: Before replacing any components, make sure to turn OFF the vacuum cleaner.
Remove the power plug from the outlet.
4.1. Dust box cover assembly
removal
1. Open the dust box cover assembly at an angle of approx.
45°. Insert a flat-blade screwdriver between the upper
body and the dust box cover assembly and move it in the
direction of the arrow mark to remove the dust box cover
assembly from its right side.
4.2. Separate the upper and lower
body units
1. Remove the five screws fixing the upper body U and
lower body U.
2. Remove the screw fixing the upper body U from the rear
side.
7
3. Lift the upper body U to separate it from the lower body U.
4.3. Printed Circuit Board A Unit
(P.C.B A Unit) removal
1. Remove the Control knob U and switch cover U.
2. Figure 7 illustrates the main body with the control knob U
and switch cover U removed.
3. Remove the P.C.B. AU from the P.C.B holder and discon-
nect the fast-on terminal on the lead wire connected to
the P.C.B. A Unit
Caution: Disconnect the fast-on terminal straight so
that lateral forces are not applied to the terminal fitted
to the P.C.B. AUnit.
8
4.4. Motor removal
1. Remove the dust box lid assembly. (Refer to paragraph
4.1 on P.6)
2. Remove the upper body from the lower body. (Refer to
paragraph 4.2 on P.6)
3. Remove the P.C.B A Unit. (Refer to paragraph 4.3 on P.7)
4. Remove the two screws fixing the P.C.B holder and pull it
out from the lower body.
5. Lift the motor set section from the lower body U.
6. Remove all components fitted to the motor.
a. Remove the motor support rubber (front).
b. Remove the motor support rubber (rear).
c. Remove the motor support.
d. Remove the noise suppressor U.
e. Remove all lead wires.
9
4.5. Cord reel partition unit replace-
ment
1. Increase the gap width between the cord reel and the
lower body with a screwdriver. While removing the cord
reel shaft from the side of the lower body, lift the cord reel
partition unit.
* For easy removal, pull out the cord slightly, and
then lift the cord reel.
4.6. Rail base U replacement
1. Remove the screw fixing the rail base U onto the cord reel
partition U.
2. Remove the rail base U from the cord reel partition U.
4.7. Spring-loaded cord reel pre-
winding
1. The cord reel partition U has a spring that pre-winds the
cord reel.
If the cord is not wound, then press the brake arm, and
the cord pre-winding will be loosened.
If you wish to apply pre-winding again, then wind the cord
three turns in the direction of the arrow mark.
* If you wish to release the pre-winding, then make
sure to hold the cord plug.
10
4.8. How to disassemble the
turbine nozzle
4.8.1. Agitator ass'y
1. Rotate the Lock on the brush cover to unlock and remove
the brush cover U.
2. Pull up the agitator ass’y and remove the belt and agitator
ass’y (complete). (Fig.16)
4.8.2. Separation of the floor nozzle
upper U from the floor nozzle
lower U
1. Remove the four screws fixing the floor nozzle lower U.
(Fig.17)
2. Remove the floor nozzle lower U.
4.8.3. Turbine Ass’y
1. Pull up the floor nozzle wand U and remove the turbine
ass’y. (Fig.18)
4.8.4. Removal of the floor nozzle brush
CU.DU.EU.FU
1. Turn the floor nozzle lower unit over. Insert the tip of a
flat-blade screwdriver into the ditch in the brush installa-
tion part, then remove the brush.(Fig.19)
Inhaltsverzeichnis
Andere Panasonic Staubsauger Handbücher
Panasonic
Panasonic MCE583 - UPRIGHT VAC.-PLAT Bedienungsanleitung
Panasonic
Panasonic MC-UL915 Bedienungsanleitung
Panasonic
Panasonic QuickDraw MC-V7375 Bedienungsanleitung
Panasonic
Panasonic MCUG589 - PLATINUM UPRIGHT VACUUM Bedienungsanleitung
Panasonic
Panasonic MC-CG882-SC79 Bedienungsanleitung
Panasonic
Panasonic MC-CG524 Bedienungsanleitung
Panasonic
Panasonic MC-CL779 Bedienungsanleitung
Panasonic
Panasonic MCUL671 - UPRIGHT VAC - MULTI LANGUAGE Bedienungsanleitung
Panasonic
Panasonic MC-UL955 Bedienungsanleitung
Panasonic
Panasonic MC-V414 Bedienungsanleitung
Panasonic
Panasonic MC-CG525 Bedienungsanleitung
Panasonic
Panasonic MC-CG881K Bedienungsanleitung
Panasonic
Panasonic MCV5706 - UPRIGHT VACUUM Bedienungsanleitung
Panasonic
Panasonic QuickDraw MC-V7357 Bedienungsanleitung
Panasonic
Panasonic MC-CL675-ZC79 Bedienungsanleitung
Panasonic
Panasonic MC-E4061-00 Bedienungsanleitung
Panasonic
Panasonic MC-CG881C-SC79 Bedienungsanleitung
Panasonic
Panasonic MCV5271 - UPRIGHT VACUUM PLAT Bedienungsanleitung
Panasonic
Panasonic MCUG581 - PLATINUM UPRIGHT VAC Bedienungsanleitung
Panasonic
Panasonic MCV215 - COMMERCIAL VACUUM Bedienungsanleitung
