ParaBody 701 Bedienungsanleitung

701

PARABODY525 PEC DEC OPTION

PRODUCT ASSEMBLY

INSTRUCTIONS SHEETS

t t t ATTENTION t ~t

.e~,~ ~~

~F O~NE ~

_ONE(1) L 0 CK.~ NUT,

BOLT,

WASH~

,ux r~t~tl ~z~ fist, IJtst~ AI 1. AbbENIIgL¥ PARTS LIST (/~EVEL 1,)

SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSE1VII3LY

ITEM NAME/DESCRIPTION QTY

10.

I1.

12.

13.

14.

I/2x4-I/2IN.BOLT.............................................................................................................. 2

318X2IN.BOLT.................................................................................................................... 2

3/4IN.WASHER...................................................................................................................... 4

1/2IN.WASHER.................................................................................................................... 4

318IN.WASHER................................................................................................................... 2

l/2IN.LOCKNUT............................................................................................................... 2

3/8IN.LOCKNUT................................................................................................................ 2

COTTERLESSHITCHPIN....................................................................................................

CABLERETAFNINGCLIP..................................................................................................... 2

3/4I.D.STARLOCKCOLLAR.............................................................................................

3/4 IN. FLANGEBEARING................ ¯................................................................................. 2

KNOB..................................................................................................................................... 2

CARRIAGEGUIDE............................................................................................................... 6

2IN.SQ.ENDCAP.................................. : ...........................................................................

VCELDMENTS/PARTS:

ITEM NAME/DESCRIPTION

BEARINGHOUSING.................................................... (6352701).................................... :.... I

CENTERPULLEYBRACKET...................................... (6352401)....................................... I

RIGHTPECDECARM................................................. (6354101)....................................... I

LEFT PEC DEC ARM (6354201)........ 7"2".......................... 1

""................................................... -. .,-" .<. o ~.... [1

RIGHTARMADVANCE.............................................. (63~2101-)...... : ............................

~¢;S~t~_tN4t.,- . :..:.,.~ I ,.,/ l

LEFTARMADVANCE................................................ , ....... , ......................................

4 X12ROLLERPAD..................................................... (6176201)....................................... 2

4-t~X1 IN.PULLEY............................................. ,...(3116101)....................................... 2

NOTE: BOLT LENGTH IS MEASUREDFROM THE UNDERSIDE OF THE HEAD OF THE BOLT.

BOLT LENGTH

BOLT LENGTH RULER:

701 FACTOR525 PEC DEC ATT. ASSEMBLYPARTS LIST (LEVEL 2)

SORT AND COUNTALL PARTS BEFOREBEGINNINGASSE/VIBLY

ITEM NAME/DESCRIPTION QTY

I. ~/~x2rs.BOLT

3/8 IN. WASHER...................................

4. I/4I~.WASH~-R..............................

2..........

2.....................................................................

25. ~z~r~.LOCKNut..........................

22.2222222222222.222222222222222222"222222......

22........................

6. ~/8rs.LOW~*G~rLOCK~................................

2..22..22.2.2...222.2222222.22222222222222222222222

~. ,/~-2~~N.NUT......................

222222522522222222222222252222222"222"2"2"2.....

"2"2""2......................................

10. PULLEYB~CKET......................... "..................................................................... 1

l 1. SWIVEL................................................................................... 1

~ELDMENTS~ARTS:

ITEM NAME~ESCRIPTION Q~

L~K CABLE ................................................................. (6371801)....................................... l

LOOPCABLE................................................................ (637I101)....................................... I

SHOCK CO~ ............................................................... (6271801)..................................... 1

4-I/2 X 1 IN. PULLEY " "

................................................... (311610I)....................................... 3

BOLT LENGTH IS MEASUREDFROM THE UNDERSIDE OF THE HEAD OF THE BOLT.

NOTE:

BOLT LENGTH RULER:

0123

COTERLESSHITCH PIN (2)----------_.~

LEFT PEC DEC .

2 SQ. END CAP

RIGHT PEC DEC ,~

EY BRACKET

3/4 IN. WASHER

LEFT ARM ADVANCE

RIGHT ARM ADVANCE~

"-...4 X PAD --~

.‘ ~ I..2 ROLLER

(2)

"-.. ~’ /-- CAM STOR

CARRIAGEGUIDES (2)

-’-~’-

HO°’-ING

-’’’’" ""’~ BEARING u~

/¯l /

//’ !.. TAR’ CK COLOR 2

/s/~ D S ~o ( )

~2 SQ. END C~~ (2) ~d~ P~BODY ~C.

~AS~ INSL 701101

701 FACTOR525 PEC DEC ATT. ASSEMBLYINSTRUCTIONS

NOTE:

(LEVEL1)

IF THE SHROUDIS ASSEMBLEDTO THE FACI’OR 525, IT WILLNEEDTO BE REPdOVED

TO ASSEMBLETHE PEG DEC ATTACHMENT.PLEASE REMOVETHE SHROUDAT THIS

TIME BY CAREFULLYREMOVINGTIIE FOURTEEN(14) SHROUDFASTENEFKg.

10.

Insert two (2) 2 IN. SQ. ENDCAPSinto both ends of the BEARINGHOUSING,as shownon drawing.

SECURELYassemble the BEARINGHOUSINGand the CENTERPULLEYBRACKETto the

FRONTUPRIGHTas shownon drawing, using p, vo (2) I/’2 X4-1/2 IN. BOLTS,four (4) I~

WASHERS,and two (2) I/2. IN. LOCKNUTS. (TttE CONNECTORPLATESON THEBEARING

HOUSING AND THE CENTER PULLEY BRACKET HAVE SLOTTED HOLES. SHIFT THE

BEARING HOUSING DOWNAND THE CENTER PULLEY BRACKET UP AS FAR AS

POSSIBLE) ¢°

Insert four (4) 2 IN. SQ. ENDCAPSinto BOTHENDSof the LEFT, and RIGHTPECDECARMS

shownon drawing.

Assemble one (1) 3/4 IN: WASHER,and the LEFTARM.a DVANCEto the LEFTPEC DECARM

shownon drawing. Also Assembleone (1) 3/4 IN. WASIl[’2t~., :,,td the RIGHTARMADVANCEto the

RIGHT PEC DEC ARMas shown.

Insert four (4) 3/4 IN. FLANGEBEARINGSinto {he BUSHINGSof the BEARINGHOUSING,

shownon drawing.

Insert the LEFTand RIGHTPECDECARMSthrough the 3/4 IN. FLANGEBEARINGSin the

BEARINGHOUSINGon their respective sides as shown on drawing, ~d SECUREthem in place with

two (2) 3/d I.D. STARLOCKCOLLARS.

Slide two (2) 4 X 12 ROLLERPADSonto the LEFTand RIGHTPECDECARMS,until the

ROLLERPADis FLUSHwith the bottom or’the ARMS.(IF A LUBRICANTIS REQUIRED,COAT

THE INSIDE OF THE ROLLER PAD WITII RUBIJINC ALCOIIOL. ALSO, ROTATING THE

PAD WHILE PUSHINGUP ’,VILL I lELP TO EASE ASSEMBLY)

Assemble t~vo (2) KNOBSto two (2) COTTERLESSHITCHPINSas shown on drawing. Insert the

(2) co’r-FERLESS HITCHPINS through the BUSHINGSon the CAMSof the RIGHTand LEFTPEC

DEC ARMS,and into the holes on the PEC ARMADVANCES.SEE DRAWING.

Attach two (2) CAP.RIAGEGUll)USto the CA~ISTOPo,~ the IIEARINGI1OUSINGwhere the

ARMADVANCESmakes contact with the CANt STOP.

LOOSELYassemble txvo (2) 4-1/2_ X IN. PULLEYS and ~wo (2 ) CABLE RETAINING CLIPS to the

CENTERPULLEYBRACKETas shownon drawing, using two (2) 3/8 X 2 IN. BOLTS,four (4) 3/8

WASHERS,and two (2) 3/8 IN. LOCKNUTS. (NOTE: THIS CONNECTIONWILL

TIGHTENED AFTER THE CABLE ttAS BEEN ROUTED)

THIS CONCLUDES THE ASSFMBLY OF (LEVEL

4o "

’7.

FACTOR525 PEC DEC ATT. ASSEMBLYINSTRUCTIONS(LEVEL 2) __

LOOSENthe 3/8 X4 1N. BOLTthat ~ssembles the two (2) PULLEYS,and two (2) I/2 IN. SPACERS

the BASEdirectly behind the FRONTUPRIGHT.Removethe 3/8 IN. LOCKNUT,and the 3/8 IN.

WASHER..Slide the BOLTout enoughto removethe two (2) 1/2 IN. SPACERS.Replace if.it I/2 IN.

SPACERSwith one (I) .~-I~ X I IN. PULLEY,as shownin (VIEWB-B). Slide BOLTback

Replace the 3/8 IN. WASHER.,and 3/8 IN. NUT. TIGHTENCONNECTIONSECURELY.

SECURELYassemble one (I) 4-I/2 X 1 IN. PULLEYto the single hole in the BASEdirectly behind the

FRONTUPRIGHTas shown in (VIEWB-B) on drawing, using one (I) 3/8 XI-3/4 IN. BOLT,two

3/8 IN. WASHERS,and one (1) 3/8 IN. LOCKNUT.

To assemble the LOOPCABLE,follow the cable routing diagram on drawing, and use the following

steps:

Assemble one end of the LOOPCABLEto the LEFTARMADVANCEand the other cad ofthe

LOOP CABLE to the RIGHT ARMADVANCE(MAKE SURE THAT LOOP CABI3E IS

ROUTED BETWEENTHE AB CRUNCHCABLE AND THE FRONT UPRIGHT) as shown

on drawing, using~.wo (2) 318 IN. NUT,four (4) 3/8 IN. WASHERS,and two (2) 3/8 IN.

HEIGItT LOCK NUT. (TIGHTEN THE CONNECTION ENOUGHTO REMOVE’rile

PLAY, YET AL].,OWING THE LOOP TO MOVEFREELY)

¯Drape the CABLEover the both PULLEYSon the CENTERPULLEYBI~.CKET. (THIS

WILL FORM A LOOP IN THE CENTER OF THE CABLE)

¯Position CABLERETAININGCLIPS in a 45 DEGREEposition over the PULLEYSand

CABLES,and tighten the two (2) PULLEYconnections SECURELY.SEE DRA’~/ING.

To assemble the LINKCABLE,follow the cable routing diagram on drawing, and use the iblt~wing steps:

®LOOSELYassemble the PULLt:YBRACKETto the LINKCABLEas shown in (DE’.[’AIL E)

drawing, using two (2) I/4 IN. WASI-tER,and two (2) 1/4-28 IN. NUTS.(LOCATEPULLEY

BRACKET HALF WAY UP ONTItETItREADSOFTHELINKCABLE" DO NOT

TIGHTEN NUTS AT TItlS TIME)

,, Slip one (1) 4-1/2 X I IN. PULLEYinto the LOOPofthe LOOPCABLEcreated from routing

STEP3. (VIEWD-D) While holding fl~at PULLEYin the LOOP,SECURELYassemble the

PULLEYBtL4.CKETover the PULLEYas shown in (DETAILE) on drawing, using one (1) 318

2 IN. BOLT,two (2) 3,’8 IN. \VASI-I~RS,and one (I) 3~8 IN. LOCK

¯Route the LINKCABLEas shown on drawing. (ALSOSEE VIEWB-B)

oRunthe LINKCABLEthrough the pre-deterrnined hole of ~he D-RINGas shownin (’.DETAILA)

and attach one (I) D-RINGCABLECLIParound the ball end of the LINKCABLE.

Attach one (I) SHOCKCORDto the D-RINGCABLECLIP on the end of the LINKCABLEas shovrn

in (DETAILA).

Route the SHOCKCORDup and around the: pro-determined 2 IN. PULLEYabove the D-RINGas shown

in (VIEWC-C). and down~o the BASE.

Attach one (1) SWIVELto the end of the SHOCKCORD.Slip ti;e end of the SWIVELover the L-PIN

on the BASE,and position the SWIVELdirectl: over the FIRSTPULLEYas shown in (VIEWB-B)

drawing.

701 FACTOR525 PEC DEC ATT. ASSEMBLYINSTRUCTIONS(LEVEL 2)

The D-lUNGCABLECLIPon the end of the LINKCABLEshouid restljust above the D-RING.If the

LINKCABLEseemsto be pulling on the D-RINGor is resting too far above the D-RING,adjust it by

raising or lowering the two (2) 1/4-2~ IN. NUTSthat attaches the LINKCABLEto the PULLEY

BRACKET.Whenthe correct height is obtained SECURELYtightea the two (2) 1/4-28 NUTStogether

around the PULLEYBRACKET.

9. To adjust the pre-streteh on the PECDECARMS:

¯Pull up on the COTTERLESSHITCHPIN.

Swivel the ARMforward or backward.

Let the PIN drop downinto one of the two holes in the PECARMADVANCES.

¯Or let the PIN drop behind the PECARMADVANCES.

NOTE: IF ASSEMBLING THE LEG PRESS ATTACHMENTNEXT, STOP HERE AND REFER TO

THOSE ASSEMBLY INSTRUCTIONS. IF ONLY ASSEMBLING TIIE PEC DEC ATTACHMENT

TO BASE UNIT, .CONTINUE ON WITH THESE ASSEMBLYINSTRUCTIONS.

I0. Wrapthe SHROUDaround the C/’,BLES that route to the D-RING,and assemble the SHROUDto

BOTHSIDESof’the/VIIDDLEU, PRIGHTas shownin (VIEWF-F) on drawing, using the fourteen (I-t)

SHROUDFASTENERS. "

THIS CONCLUDESTHE ASSE~,IBLY OF (LEVEL 2), AND

THE ASSEMBLY OF THE PEC DEC ATTACHMENT FOR

THE FACTOR525 BASE UNIT.

.!!

o ;

L-PIN

--~

FRON’FOFMACHINE

SEE VIEW C-C

/-_D-R~NG

DETAILA

~S__HR__C,UD(’SEEVIEW

j-t.INK CABL[

x 2

PULL-

LINKCA-

CD-RING

MIDDLEUPRIGHT

Vl~ F-F

VIEW B-B

FRONTOF MACHINE

DETAIL C-C

VIEW D-D

FASTENERS04)

Andere Handbücher für 701

Dieses Handbuch passt für folgende Modelle

Andere ParaBody Heim-Fitnessstudio Handbücher

ParaBody

ParaBody 445104 Bedienungsanleitung

ParaBody

ParaBody 897104 Bedienungsanleitung

ParaBody

ParaBody PBF065 Bedienungsanleitung

ParaBody

ParaBody PBF203B Kurzanleitung

ParaBody

ParaBody 874 Bedienungsanleitung

ParaBody

ParaBody Serious Steel 812102 Bedienungsanleitung

ParaBody

ParaBody 458 Bedienungsanleitung

ParaBody

ParaBody ex 350 Bedienungsanleitung

ParaBody

ParaBody 841101 Bedienungsanleitung

ParaBody

ParaBody 400102 Bedienungsanleitung

ParaBody

ParaBody 359101 Bedienungsanleitung

ParaBody

ParaBody 893103 Bedienungsanleitung

ParaBody

ParaBody 911101 Bedienungsanleitung

ParaBody

ParaBody LP5 Bedienungsanleitung

ParaBody

ParaBody PBF206 Installationsanleitung

ParaBody

ParaBody 221 Bedienungsanleitung

ParaBody

ParaBody Serious Steel 425103 Bedienungsanleitung

ParaBody

ParaBody FACTOR 625 Bedienungsanleitung

ParaBody

ParaBody 662101 Installationsanleitung

ParaBody

ParaBody 425103 Bedienungsanleitung

ParaBody

ParaBody 440 Bedienungsanleitung

ParaBody

ParaBody 435103 Bedienungsanleitung

ParaBody

ParaBody 829 Bedienungsanleitung

ParaBody

ParaBody 462 Bedienungsanleitung

Beliebte Heim-Fitnessstudio Handbücher anderer Marken

Horizon Fitness

Horizon Fitness OXFORD 6 Bedienungsanleitung

Energetics

Energetics Multi Trainer 5.1 Bedienungsanleitung

Matrix

Matrix MG-PL Series Bedienungsanleitung

Reebok

Reebok Tbr2i Bedienungs- und Wartungshandbuch

Weider

Weider 8300 Hard Drive Bedienungsanleitung

Pure Fitness

Pure Fitness 8526HE Bedienungsanleitung

Weider

Weider 8700 I Kurzanleitung

Bowflex

Bowflex Sport 001-6961 Bedienungsanleitung

NordicTrack

NordicTrack E8200 Competition Bench Kurzanleitung

Weider

Weider WEMC10161 Bedienungsanleitung

Body Solid

Body Solid GHYP-345 Bedienungsanleitung

Evo

Evo TAHOE 5105 Bedienungsanleitung

JLL

JLL Ventus Pro Air Power Bedienungsanleitung

Trojan

Trojan Colorado 370 Bedienungsanleitung

Octane Fitness

Octane Fitness xRide xR650 Bedienungsanleitung

Precor

Precor Discovery Series Bedienungsanleitung

Insportline

Insportline RW600 Bedienungsanleitung

Stamina

Stamina 55-1532 Bedienungsanleitung