Paradyne MIM-4000F Bedienungsanleitung

MIM4-A2-GZ40-00 December 2004 1

MIM-4000F

Installation Instructions

Document Number MIM4-A2-GZ40-00

December 2004

Contents

Software and Firmware License Agreement ...................................................... 1

Product Documentation Online .......................................................................... 3

Unpacking and Inspecting the Equipment ......................................................... 3

Installing the MIM-4000F ................................................................................... 3

Installing and Cabling SFP Transceivers ........................................................... 4

Managing the MIM-4000F .................................................................................. 4

LED Indicators ................................................................................................... 5

Regulatory Notices ............................................................................................ 5

Warranty, Sales, Service, and Training Information ........................................... 6

Software and Firmware License Agreement

The terms and conditions of this License Agreement (the “Agreement”) will apply

to the software and/or firmware (individually or collectively the “Software”)

incorporated into the Paradyne product (the “Product”) purchased by you and any

derivatives obtained from the Software, including any copy of either. If you have

executed a separate written agreement covering the Software supplied to you

under this purchase, such separate written agreement shall govern.

Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to

accept a personal, non-transferable, non-exclusive, right (without the right to

sublicense) to use the Software, solely as it is intended and solely as incorporated

ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS

TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED

INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU

SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS

LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS

ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE

LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE

LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU

WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT

PURCHASED BY YOU.

2December 2004 MIM4-A2-GZ40-00

in the Product purchased from Paradyne or its authorized distributor or reseller

under the following terms and conditions:

1. Ownership: The Software is the sole property of Paradyne and/or its licensors.

The Licensee acquires no title, right or interest in the Software other than the

license granted under this Agreement.

2. Licensee shall not use the Software in any country other than the country in

which the Product was rightfully purchased except upon prior written notice to

Paradyne and an agreement in writing to additional terms.

3. The Licensee shall not reverse engineer, decompile or disassemble the

Software in whole or in part.

4. The Licensee shall not copy the Software except for a single archival copy.

5. Except for the Product warranty contained in the manual, the Software is

provided “AS IS” and in its present state and condition and Paradyne makes

no other warranty whatsoever with respect to the Product purchased by you.

THIS AGREEMENT EXPRESSLY EXCLUDES ALL OTHER WARRANTIES,

WHETHER EXPRESS OR IMPLIED, OR ORAL OR WRITTEN, INCLUDING

WITHOUT LIMITATION:

a. Any warranty that the Software is error-free, will operate uninterrupted in

your operating environment, or is compatible with any equipment or

software configurations; and

b. ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT

LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS

FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.

Some states or other jurisdictions do not allow the exclusion of implied

warranties on limitations on how long an implied warranty lasts, so the above

limitations may not apply to you. This warranty gives you specific legal rights,

and you may also have other rights which vary from one state or jurisdiction to

another.

6. In no event will Paradyne be liable to Licensee for any consequential,

incidental, punitive or special damages, including any lost profits or lost

savings, loss of business information or business interruption or other

pecuniary loss arising out of the use or inability to use the Software, whether

based on contract, tort, warranty or other legal or equitable grounds, even if

Paradyne has been advised of the possibility of such damages, or for any

claim by any third party.

7. The rights granted under this Agreement may not be assigned, sublicensed or

otherwise transferred by the Licensee to any third party without the prior

written consent of Paradyne.

8. This Agreement and the license granted under this Agreement shall be

terminated in the event of breach by the Licensee of any provisions of this

Agreement.

9. Upon such termination, the Licensee shall refrain from any further use of the

Software and destroy the original and all copies of the Software in the

possession of Licensee together with all documentation and related materials.

10. This Agreement shall be governed by the laws of the State of Florida, without

regard to its provisions concerning conflicts of laws.

MIM4-A2-GZ40-00 December 2004 3

Product Documentation Online

Complete documentation for Paradyne products is available at

www.paradyne.com. Select Support →Technical Manuals.

To order a paper copy of a Paradyne document, or to speak with a sales representative,

please call 1-727-530-2000.

Unpacking and Inspecting the Equipment

HANDLING PRECAUTIONS FOR

STATIC-SENSITIVE DEVICES

This product is designed to protect sensitive components from damage

due to electrostatic discharge (ESD) during normal operation. When

performing installation procedures, however, take proper static control

precautions to prevent damage to equipment. If you are not sure of the

proper static control precautions, contact your nearest sales or service

representative.

If there is any visible damage, do not attempt to install the MIM-4000F; contact

your sales representative.

Installing the MIM-4000F

The MIM-4000F Micro Interface Module provides additional uplink ports for the

BSX8000-5 Broadband Services Switch.

All MIMs are hot swappable, although removal of a MIM disengages the upstream

network connection for the DSLAM.

To install the MIM-4000F:

Procedure

1. Using a flat-blade screwdriver to loosen the fastening screws, remove the

cover plate from the MIM port on the front of your BSX8000.

CAUTION: The cover plate should be stored for possible future use: if the MIM

is removed from your BSX8000, it must be replaced with either another MIM or

a cover plate. Do not operate a BSX8000 with an open MIM port.

2. Align the MIM-4000F with the module guides inside the MIM port.

LADLADLADLAD

MIM-4000F

04-17599

4December 2004 MIM4-A2-GZ40-00

3. Slide the MIM-4000F firmly into place. Do not use excessive force.

4. Secure the MIM-4000F by tightening the fastening screws on the MIM

faceplate with a flat-blade screwdriver.

Installing and Cabling SFP Transceivers

The following SFP transceivers are available for installation in the MIM-4000F:

SFP-MMF – Gbe SFP Multimode Fiber Optic Transceiver, Short Reach

SFP-SMF10 – Gbe SFP Single Mode Fiber Optic Transceiver, 10Km Reach

SFP-SMF40 – Gbe SFP Single Mode Fiber Optic Transceiver, 40Km Reach

SFP-SMF80 – Gbe SFP Single Mode Fiber Optic Transceiver, 80Km Reach

To install SFP transceivers in the MIM-4000F:

Procedure

1. Insert an SFP transceiver into an SFP socket on the MIM-4000F.

2. Insert the LC connector of your fiber optic cable into the SFP transceiver.

3. Observing the minimum bend radius for your cable, fasten it in such a way that

it will not be kinked or snagged in the course of other cabling. If you do not

know the specifications for your cable, maintain a radius of at least ten times

the cable diameter.

4. Repeat for all the sockets you intend to use.

Managing the MIM-4000F

The configuration and monitoring of the integrated switch on the MIM-4000F is

performed through the management screens of the BSX8000 that hosts this

module.

04-17600

LAD

MIM-4000F

MIM4-A2-GZ40-00 December 2004 5

LED Indicators

Each of ports 1–4 is associated with three LEDs: L (Link), A (Active), and

D(Duplex):

Regulatory Notices

UNITED STATES – EMI NOTICE:

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC rules. These limits

are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

The authority to operate this equipment is conditioned by the

requirements that no modifications will be made to the equipment

unless the changes or modifications are expressly approved by

Paradyne Corporation.

CANADA – EMI NOTICE:

This Class A digital apparatus meets all requirements of the Canadian

interference-causing equipment regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du

règlement sur le matérial brouilleur du Canada.

Table 1. Front Panel LEDs

LED State Indication

L (Link) Solid green Connection is established

No illumination Connection is not established

A (Active) No illumination No data activity on the circuit

Pulsing amber Data is flowing through the circuit

D (Duplex) Green Full duplex mode

Amber Half duplex mode

6December 2004 MIM4-A2-GZ40-00

EUROPEAN REGULATORY COMPLIANCE

The following regulatory compliance information applies to the

MIM-4000F as installed in the BSX8000-5:

This Class A product complies with European Norm EN55022.

Warning: In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate

measures to correct the situation.

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor

directly for any help needed. For additional information concerning warranty, sales,

service, repair, installation, documentation, training, distributor locations, or

Paradyne worldwide office locations, use one of the following methods:

Internet: Visit the Paradyne World Wide Web site at www.paradyne.com.

(Be sure to register your warranty at www.paradyne.com/warranty.)

Telephone: Call our automated system to receive current information by fax or

to speak with a company representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A., call 1-727-530-2340

!!.

*MIM4-A2-GZ40-00*

Inhaltsverzeichnis

Andere Paradyne Netzwerk-Hardware Handbücher

Paradyne

Paradyne 8310 MVLt Bedienungsanleitung

Paradyne

Paradyne MIM-2E1 Bedienungsanleitung

Paradyne

Paradyne COMSPHERE 3610 Bedienungsanleitung

Paradyne

Paradyne GranDSLAM 4200 Bedienungsanleitung

Paradyne

Paradyne COMSPHERE 3610 Handbuch

Paradyne

Paradyne COMSPHERE 3610 Bedienungs- und Wartungshandbuch

Paradyne

Paradyne Application Module 9109 OCU-DP Bedienungsanleitung

Paradyne

Paradyne Comsphere 3510 Bedienungsanleitung

Paradyne

Paradyne 4300 Bedienungsanleitung

Paradyne

Paradyne COMSPHERE 6700 Series Bedienungsanleitung

Paradyne

Paradyne FrameSaver NP 64+ Bedienungsanleitung

Paradyne

Paradyne FrameSaver NP 100 Bedienungsanleitung

Paradyne

Paradyne 7915-A1 E1 SDSL Bedienungsanleitung

Paradyne

Paradyne Jetstream CPX-1000 Bedienungsanleitung

Paradyne

Paradyne COMSPHERE 3610 Stücklistenhandbuch

Paradyne

Paradyne FrameSaver NP 100 Bedienungsanleitung

Paradyne

Paradyne COMSPHERE 6700 Series Bedienungsanleitung

Paradyne

Paradyne JetFusion Integrated Access Device Bedienungsanleitung

Paradyne

Paradyne ACCULINK 3160 Handbuch

Paradyne

Paradyne HotWire 7924 Bedienungsanleitung

Paradyne

Paradyne COMSPHERE 3550 Series Bedienungsanleitung

Paradyne

Paradyne Hotwire 6210 Original Betriebsanleitung

Paradyne

Paradyne COMSPHERE 6700 Series Bedienungsanleitung

Paradyne

Paradyne BitStorm 2600 IP DSLAM Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung