PEERLESS A100IWBMOUNT Leitfaden

ISSUED:08-08-08 SHEET#:055-9094-1

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

1 of 16

Installation and Assembly: Wallmount for CPA100 and

Whiteboard

Model: A100IWBMOUNT

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

Maximum Load Capacity for Screen: 53 lb (24 kg)

Maximum Load Capacity for Projector : 13.5 lb (6 kg)

ISSUED:08-08-08 SHEET#:055-9094-1

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

2 of 16

NOTE: Read entire instruction sheet before you start installation and assembly.

• DonotbegintoinstallyourPeerlessproductuntilyouhavereadandunderstoodtheinstructionsandwarnings

containedinthisInstallationSheet.Ifyouhaveanyquestionsregardinganyoftheinstructionsorwarnings,please

callPeerlesscustomercareat1-800-865-2112.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Makesure that the supporting surface will safely support the combined load of the equipment and all attached hard-

wareandcomponents.

• NeverexceedtheMaximumLoadCapacity. See pageone.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an

"edgetoedge"studfinderishighlyrecommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tightenscrewsfirmly,butdonotovertighten.Overtighteningcandamage the items, greatly reducing theirholding

power.

• Carriageboxhasover100lbs(43kg)ofpressure.Becarefulnottopinchfingers.

• Thisproductis intended for indoor use only.Useof this product outdoorscouldleadtoproductfailureandpersonal

injury.

• Thisproductwasdesignedandintendedtobemountedtothe following supporting surfaces checked below with the

hardware included in this product as specified in the installation sheet.To mount this product to an alternative support-

ing surface, contact Peerless customer care at 1 800 865-2112.

• This product was designed to be installed on the following wall construction only;

WALLCONSTRUCTION ADDITIONALHARDWARE REQUIRED

xWoodStud None

WoodBeam None

xSolidConcrete None

xCinderBlock None

xMetalStud Do not attach except with Peerless accessory kit for metal studs;

Contact Customer Service for Peerless accessory kit for metal studs.

Brick ContactCustomerService

Otherorunsure? ContactCustomer Service

WARNING

Tools Needed for Assembly

•studfinder ("edge to edge" stud finder is recommended)

•phillipsscrewdriver

•drill

•1/4" bit for concrete and cinder block wall

•1/2" bit for metal stud wall

•5/32" bit for metal or wood stud wall

•level

ISSUED:08-08-08 SHEET#:055-9094-1

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

3 of 16

Description Qty. Part #

Awall mount assembly 1 055-1841

Bprojector tube 1 055-1839

Cprojector arm 1 055-1830

Dadapter plate 1 055-1828

Ehook bracket 2 055-1840

Fvertical handle 2 055-1834

Ghorizontal handle 1 055-1835

Hprojector adapter plate 1 055-1822

Islide plate 1 055-1821

Jprojector mount 1 PRG-1

K#10-32 x 0.375" phillips screw 18 520-1130

LM6 x 12 mm serrated washer head socket pin screw 8 510-1050

M0.25"ID spacer 4 590-1050

N1/4-20 x 1.0" hex head screw 2 520-1606

O#10-32 x 3/8" serrated washer head socket pin screw 2 520-1151

P0.25" ID nylon washer 4 540-9460

Q#14 x 2.5" wood screw 6 5S1-015-C03

Racorn nut 2 530-1049

Splug 1 590-1303

T#10-32 x 1-3/8" socket pin screw 2 510-1098

Ualligator anchor 6 590-0097

V5/32" (4 mm) security allen wrench 1 560-9646

W#10-32 x 1/4" socket pin screw 1 520-1196

Xflanged bushing 1 590-1271

Yretainer bushing 1 055-1836

Parts List

Beforeyoubegin,makesureallpartsshownareincludedwithyourproduct. B

H J

MNOPQ

EF I

CARRIAGE

RST

Partsmayappearslightlydifferentthanillustrated.

ISSUED:08-08-08 SHEET#:055-9094-1

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

4 of 16

fig. 1.1

Make sure that wall mount assembly (A) is level, use it as a template to mark the top two mouting holes.

Alternatively, the top two screws can be fastened 16" apart as detailed in step 2 while making sure that they are

level. In order to set the desired height of bottom of screen in the lowest position, refer to dimension X from the chart

below.

FLOOR

PROJECTOR

SCREEN

Parts List Continued

BOTTOMOF

SCREEN

WX Y

TOP

MOUNTING

HOLES

Screen Size Dimension X

63" 36"

77'' 42"

CHART

ISSUED:08-08-08 SHEET#:055-9094-1

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

5 of 16

Make sure that the mounting holes are on the stud centerline. Drill six 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep.

Fasten two #14 x 2.5" wood screws (Q) into top mounting holes leaving a .25" of exposed thread as shown. Hook

wall mount assembly (A) onto #14 x 2.5" wood screws (Q) as shown in fig. 2.1.

Fasten four #14 x 2.5" wood screws (Q) into wall mount assembly (A) as shown in fig. 2.2. Make sure that the wall

mount assembly (A) is level, tighten all six #14 x 2.5" wood screws (Q).

Skip to step 3.

Installation to Wood Stud Wall

• Installermustverifythatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattached

hardwareandcomponents.

• Tightenwoodscrewssothatwallplateisfirmlyattached,butdonot overtighten. Overtightening can damage the

screws,greatlyreducingtheirholdingpower.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is

highlyrecommended.

• Hardwareprovidedisforattachmentofmountthroughstandard thickness drywall or plaster into woodstuds.Installers

areresponsibletoprovidehardwarefor other typesofmountingsituations.

WARNING

fig. 2.1

fig. 2.2

CARRIAGE

.25"

ISSUED:08-08-08 SHEET#:055-9094-1

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

6 of 16

CORRECT

wallplate concrete

plaster/

drywall

Installation to Solid Concrete or Cinder Block

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifications.

It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid

breakingoutthebackoftheholewhenenteringavoidorcavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Makesure that the supporting surface will safely support the combined load of the equipment and all attached hard-

wareandcomponents.

WARNING

CUTAWAYVIEW

• Tighten screws so that wall mount is firmly attached,

butdonotovertighten.Overtightening candamage

screws,greatlyreducingtheirholdingpower.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

SOLID

CONCRETE

CINDERBLOCK

• Always attach concrete anchors directly to load-

bearingconcrete.

• Neverattachconcreteanchorsto concrete covered

withplaster,drywall,orotherfinishingmaterial.If

mountingtoconcretesurfacescoveredwitha finishing

surfaceisunavoidable,thefinishingsurfacemust be

counterboredasshownbelow.Besureconcrete

anchorsdonotpullawayfromconcretewhentighten-

ing screws. If plaster/drywall is thicker than 5/8",

custom fasteners must be supplied by installer.

WARNING

2concrete

surface

Drill holes and insert anchors (U).

Place wall mount assembly (A)over anchors (U) and

secure with screws (Q).

Tighten all fasteners.

CARRIAGE

fig. 2.3

Use wall mount assembly (A) as a template to mark

mouting holes. Drill six 5/32" (4 mm) dia. holes to a

minimum depth of 2.5" (65 mm). Insert six anchors (U) in

holes flush with wall as shown (right). Fasten two #14 x

2.5" wood screws (Q) into top anchors (U) leaving a .25" of

exposed thread for each screw (Q) as shown. Hook wall

mount assembly (A) onto #14 x 2.5" wood screws (Q) as

shown in fig. 2.3. Fasten four #14 x 2.5" wood screws (Q)

into wall mount assembly (A) as shown. Make sure that the

wall mount assembly (A) is level, tighten all six #14 x 2.5"

woodscrews(Q).

Skip to step 3.

INCORRECT

wallplate

plaster/

drywall

concrete

.25"

ISSUED:08-08-08 SHEET#:055-9094-1

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

7 of 16

Drill six 1/2" holes through drywall and metal studs. NOTE: It may be necessary to drill 5/32" pilot holes prior to

drilling 1/2" holes.

Refer to instruction sheet included with Peerless accessory kit ACC 615 for metal studs to install togglers.

Fasten two 1/4-20 x 2-1/2" screws into top mounting holes leaving a .25" of exposed thread on each as shown in

fig. 2.4. Hook wall mount assembly (A) onto 1/4-20 x 2-1/2" screws.

Fasten four 1/4-20 x 2-1/2" screws into wall mount assembly (A) as shown in fig. 2.5. Make sure that the wall mount

assembly (A) is level, tighten all six 1/4-20 x 2-1/2" screws.

• Drywall must be 1/2" or thicker, and metal stud must be 24 gauge or thicker.

• Installermustverifythatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattached

hardwareandcomponents.

WARNING

Installation to Metal Stud Wall (Metal Stud Accessory Kit ACC 615 Required)

TOGGLER

Afig. 2.4

1/4-20X2-1/2"PHILLIPSSCREWS

.25"

fig. 2.5

CARRIAGE

1/4-20X2-1/2"PHILLIPSSCREWS

ISSUED:08-08-08 SHEET#:055-9094-1

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

8 of 16

CARRIAGE

77" SCREEN

CARRIAGE

63" SCREEN

Fasten three #10-32 x 0.375" phillips

screws(K)tocarriageleavingthree

threadsexposed.Attach retainer

bushing(Y)andflangedbushing(X)to

wall mount assembly (A) using two

#10-32 x 0.375" phillips screws (K).

Slide projector tube (B) into top of wall mount

assembly (A) and secure with two #10-32 x

0.375" phillips screws (K) as shown below.

NOTE: Usecorrectset of mounting holes for

the screen size as shown below.

THREETHREADS

EXPOSED

CARRIAGE

fig. 4.1

fig. 4.2

fig. 4.3

Hookadapterplate(D) onto three

#10-32 x 0.375" phillips screws (K)

as shown in fig. 4.2.

Fastenthree #10-32 x 0.375" phillips

screws (K) into adapter plate (D) as

shown in fig. 4.2. Securely tighten all

six #10-32 x 0.375" phillips

screws (K).

4-2

4-1

NOTE:Twist tube

into wall mount

assembly (A).

NOTE:Tube(B)

shouldwallmount

assembly(A)

ISSUED:08-08-08 SHEET#:055-9094-1

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

9 of 16

Fasten two #10-32 x 0.375" phillips screws (K) into adapter plate (D) leaving three threads exposed as shown in

detail 1. Hook each vertical handle (F) onto #10-32 x 0.375" phillips screw (K) as shown in fig 5.1. NOTE: Use top

slot for 77" screen or second slot from top for 63" screen. Fasten #10-32 x 0.375" phillips screws (K) through lower

slot of vertical handle (F) that lines up with the lower hole in adapter plate (D). Hole location for 77" screen is shown

in fig. 5.2. Securely tighten all four #10-32 x 0.375" phillips screws (K).

THREETHREADS

EXPOSED

DETAIL 1

fig. 5.1 fig. 5.2

63"SCREEN

77"SCREEN

Fastenhorizontalhandle(G)toverticalhandle(F) using four #10-32x0.375"phillips

screws (K) and two acorn nuts (R).Acorn nuts (R) go on below horizontal handle (G).

NOTE: 77"holelocation

shown. 63" will use second

frombottomholeonvertical

handle(F).

ISSUED:08-08-08 SHEET#:055-9094-1

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

10 of 16

Insert hook brackets into screen as shown in detail 2 and fig. 7.1. Secure each hook bracket (E) with M6 x 12 mm

serrated washer head socket pin screw (L) as shown in fig. 7.2 and detail 3.

DETAIL 3

fig. 7.2

SCREEN

fig. 7.1

77"SCREEN

63"SCREEN

DETAIL 2

SCREEN

BRACKET

Andere Handbücher für A100IWBMOUNT

Inhaltsverzeichnis

Andere PEERLESS Rack & Stand Handbücher

PEERLESS

PEERLESS Vision Point LCFS 100 Leitfaden

PEERLESS

PEERLESS PARAMOUNT PA730 Leitfaden

PEERLESS

PEERLESS PLT BLK Leitfaden

PEERLESS

PEERLESS AEC0609 Leitfaden

PEERLESS

PEERLESS WSP 420 Bedienungsanleitung

PEERLESS

PEERLESS A100IWBMOUNT Leitfaden

PEERLESS

PEERLESS RTPLA 50 Leitfaden

PEERLESS

PEERLESS HT642-002 Leitfaden

PEERLESS

PEERLESS DST360 Leitfaden

PEERLESS

PEERLESS Paramount PC930A Leitfaden

PEERLESS

PEERLESS LDS 1920U Leitfaden

PEERLESS

PEERLESS SmartMount ST 635 Leitfaden

PEERLESS

PEERLESS IBA1 Leitfaden

PEERLESS

PEERLESS PANA-85WM Leitfaden

PEERLESS

PEERLESS LCT Series Leitfaden

PEERLESS

PEERLESS PARAMOUNT PA740 Bedienungsanleitung

PEERLESS

PEERLESS Perfect Mount PMF2X2 Bedienungsanleitung

PEERLESS

PEERLESS HDS-S Leitfaden

PEERLESS

PEERLESS PLC Leitfaden

PEERLESS

PEERLESS COL 510P Leitfaden

PEERLESS

PEERLESS WBK100-W Leitfaden

PEERLESS

PEERLESS Solid-Point PS 1 Leitfaden

PEERLESS

PEERLESS IWB600-WB Leitfaden

PEERLESS

PEERLESS HCW201 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung